Panasonic EYFR03 Guida all'installazione
Panasonic
•Comparison Between Models……..………………………
•Inputs/Outputs Overview………………………………..…
•Run Screen………………………………………………....…
•Main Menu……………………………………….……….……
•Tools…………………………………………………………...
–Learn/Learn Open
–Replace/Edit/Forget (Unlearn)
•Programming Modes…………………………………….….
–Parameter Mode
–Group Mode
–Job Mode
•History………………………………………………………….
•Events………………………………………………………….
•Qualifier Settings…………………………………………….
•Protocols/Network Settings………………………………..
•Inputs/Outputs……………………………….……………….
•Update Firmware…………………………….……………….
•Check Firmware……………………………..……………….
•Assembly Manager………………………….........…………
–Connecting A PC
•Data Collection……………………………………………….
–Download Data To USB / Configuration To USB
–Upload Configuration From USB
–Create A .CSV File
Table Of Contents
Page 3
Page 4
Page 5
Page 6
Page 7
Page 9
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 27
EYFR03 Model Comparison Page 3
EYFR03 Inputs/Outputs Overview
Ethernet Connection (RJ45 Qty. 2)
Ethernet IP, Open Protocol, ToolsNet
(EYFR03A/B) Remote I/O (5 Pin Connector)
(For Future Use)–I/O Module
(Used in EYFR03A/B)
Discrete I/O (24 Pin Connector)
Used to connect directly to the assembly
line or a PLC.
8 Inputs/12 Outputs
(Used in EYFR03A)
OR
AND/
OR Socket
Tray
I/O Module
PLC
PLC
PLC
PC
Page 4
Tool Status Indicator
Unit Lock
Unit Radio Status
Network Status
Reset Batch History Status
Current
configurations
Menu
Access to setting
up the Qualifier
Password - 1011
Parameter Name &
Tool Name
Batch Count
EYFR03 Run Screen
Group View Screen Shot
Page 5
Groups
Select, View and Edit
Groups
Job
Select, View and Edit Jobs
Parameters
Select, View and Edit
Parameters
Qualifier Settings
View and Edit Global
Qualifier Settings
Events
View non-tightening events
such as programming and tool
changes, power ups, etc...
Lock & Exit
Exit and Lock Out Menu /
Returns to Run Screen
Exit
Exit Menu /
Returns to Run Screen
EYFR03 Menu Navigation
Network Settings
View and Edit General,
ACOP, ToolsNet and
EIP Network Settings
Tools
Learn and Edit Tools
Page 6
New
Menu Password
1011
Menu
(Enter)
Password
(1011 Enter)
Tools
(Enter)
Learn Tool
(Starts the learn sequence
for the highlighted tool slot)
Learn Open Tool
(Starts the learn sequence
for the first empty tool slot)
Exit Tool
(Returns to the Main Menu)
1. Remove/Replace
Battery, Pull tool
trigger for 2 seconds
2. Successful Learn -the
screen will
automatically returns
to the tool menu and
the box will turn green
3. To learn additional
tools return to the
Learn step above.
4. Exit (Returns to the
Main Menu)
1. Remove/Replace
Battery, Pull tool
trigger for 2 seconds
2. Successful Learn -the
screen will
automatically returns
to the tool menu and
the box will turn green
3. To learn additional
tools return to the
Learn step above.
4. Exit (Returns to the
Main Menu)
Tools -Learn/Learn Open
Main menu -Tools
Learn Tool Menu
Page 7
*In the case a tool can not be learned to a Qualifier, try these steps.
1. Check to see that the tools model or serial number contains an “R” which states it has a wireless card included.
2. Make sure to follow the directions on the screen –remove & replace battery then pull tool trigger and release.
3. Check the serial number to see if the tool was built on or after 15=2015/01=Jan (Ser# XXXXXXX1501XXXX),
if yes the wireless card may be disabled. To re-enable the wireless card, pull the tools trigger “7” times, each
trigger pull should show a bad fastenings (red light turns on). The tool should learn to the Qualifier.
Menu
(Enter)
Password
(1011 Enter)
Tools
(Enter)
Replace Tool
(Starts the learn sequence
for the highlighted tool slot)
Edit Tool
(Edit the highlighted tool)
Learn Open Tool
(Starts the learn sequence
for the first empty tool slot)
Exit Tool
(Returns to the Main Menu)
1. Remove/Replace
Battery, Pull tool
trigger for 2 seconds
2. Successful Learn -the
screen will
automatically returns
to the tool menu and
the box will turn green
3. To learn additional
tools return to the
Learn step above.
4. Exit (Returns to the
Main Menu)
1. Editable Fields
a. Tool Name
b. Serial Number
c. Last Calibration
d. Next Calibration
e. Last PM
f. Cycles before PM
2. Not Editable Fields
a. Radio Info
b. Cycles
1. Remove/Replace
Battery, Pull tool
trigger for 2 seconds
2. Successful Learn -the
screen will
automatically returns
to the tool menu and
the box will turn green
3. To learn additional
tools return to the
Learn step above.
4. Exit (Returns to the
Main Menu)
Save (Saves changes and
returns to the Tool Menu)
Forget (Removes tool from
Qualifier)
Cancel (Cancels changes and
returns to the Tool Menu)
Tools -Replace/Edit/Forget (Unlearn)
Main menu -Tools
Learn Tool Menu
Page 8
Parameter Mode –Select a single tool, from the learned tools, to run on an application.
•Use -When a single tool is required.
•Not to use -When a group or a sequence is required.
•Reports –Signals batch complete for each tool individually.
Group Mode –Select a group of tools, up to 16 tools, to run in any order or
simultaneously.
•Uses -When a group of tools are required with a group batch complete.
•Not to use -When a sequence is required.
•Reports -Signals batch complete once the group all fasteners are completed for each tool.
Free Run Mode –Each tool can run independently and report an independent batch complete for each tool.
•Uses -When a group of tools are required with individual tool batch complete.
•Not to use -When a sequence is required.
•Reports -Signals batch complete for each tool independently.
Job Mode –Select up to 16 tools and/or a group of tools to run in a sequence.
•Uses –When a specific sequence is required.
•Not to use –When a basic rundown is needed (such as parameter mode).
•Reports –Signals batch complete when all of the tools have completed their individual steps.
EYFR03 Programming Modes Page 9
Menu
(Enter)
Password
(1011 Enter)
Parameters
(Enter)
Select Parameter
(Arrow over to a Parameter to
Create/Edit (Enter))
Edit the
Parameter as
necessary.
Press “Save” and the
Qualifier returns to the
Choose Parameter Screen
Arrow over to the
Parameter to run,
Press “Select”
EYFR03 Create And Run A Parameter
The Run Screen should be
showing and is now ready
to run a Parameter
*When a tool is learned into the
Qualifier, a parameter is
automatically created and the tool
is automatically connected to the
corresponding parameter.
(ie. Tool1=Parameter1,
Tool2=Parameter2, …,
Tool16=Parameter16)
Main menu -Parameters Parameter Edit Screen
Page 10
Altri manuali per EYFR03
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Panasonic Controllori
Panasonic
Panasonic FP0H Series Manuale utente
Panasonic
Panasonic AWRP605P - MULTI FUNCTION CONTROLLER Manuale utente
Panasonic
Panasonic FP-XH Series Manuale utente
Panasonic
Panasonic MGSDB2 Series Manuale utente
Panasonic
Panasonic FV-WCCS1-W Manuale utente
Panasonic
Panasonic CZ-256ESMC2U Manuale utente
Panasonic
Panasonic CZ-ANC2 Manuale utente
Panasonic
Panasonic WRKT4504E Series Manuale utente
Panasonic
Panasonic EYFRZ01 Manuale utente
Panasonic
Panasonic FP7 Series Manuale utente
Panasonic
Panasonic FP2 -C1A Manuale utente
Panasonic
Panasonic AFPX-C30R Manuale utente
Panasonic
Panasonic FP E Series Manuale utente
Panasonic
Panasonic AW-RP60G Manuale utente
Panasonic
Panasonic CZ-256ESMC3 Manuale utente
Panasonic
Panasonic CZ-RE2C2 Manuale utente
Panasonic
Panasonic FP7 Series Manuale utente
Panasonic
Panasonic Minas A4 Series Manuale utente
Panasonic
Panasonic WVCU550C - SYSTEM CONTROLLER UNIT Manuale utente
Panasonic
Panasonic FP-I4C Manuale utente
