Panasonic DVD-S42EE Manuale utente

ORDERNO.CHM0603009CE

DVDPlayer

DVD-S42EE / DVD-S42GC / DVD-S42GCA / DVD-S42GCS /

DVD-S42GCU / DVD-S42PL / DVD-S42PLA

DL4.1Mechanism Series

Color

(S).......................Silver Type

SPECIFICATIONS

Specifications

Power supply: AC230 V, 50 Hz

(DVD-S42EE)

AC110-240 V, 50/60 Hz

(DVD-S42GC/GCA/GCU/GCS/

PL)

AC120 V, 60 Hz

(DVD-S42PLA)

Power consumption: 11 W

Power consumption instandbymode:

1W(approx.)

Dimensions: 430 (W) × 251 (D) × 43 (H) mm

Mass: 2.2kg(approx.)

Signal system: PAL625/50, PAL525/60, NTSC

(DVD-S42EE/GC/GCA/GCS/

GCU)

NTSC

(DVD-S42PLA/PL)

Operating temperature range: + 5to+ 35 °C

Operating humidityrange: 5to90 %RH (no

condensation)

Discs played[8cm (3") or12 cm (5")]:

(1) DVD (DVD-Video, DivX*6,7)

(2) DVD-RAM (DVD-VR, JPEG*4,7, MPEG4*5,7, DivX*6,7,

MP3*2,7)

(3) DVD-R (DVD-Video, DVD-VR, JPEG*4,7, MP3*2,7, DivX*

6,7, MPEG4*5,7)

(4) DVD-R DL(DVD-Video, DVD-VR)

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

(5) DVD-RW(DVD-Video, DVD-VR, JPEG*4,7, MP3*2,7, DivX*

6,7, MPEG4*5,7)

(6) +R/+RW(Video)

(7) +R DL(Video)

(8) CD, CD-R / CD-RW(CD-DA, VideoCD, SVCD*1, MP3*2,7,

WMA*3,7, JPEG*4,7 , MPEG4*5,7, DivX*6,7,

HighMATLevel 2(Audioand Image))

*1 Conforming toIEC62107

*2 MPEG-1Layer 3, MPEG-2Layer 3

*3 WindowsMediaAudioVer.9.0L3

Not compatiblewithMultipleBit Rate(MBR)

*4 Exif Ver2.1JPEG Baselinefiles

Picture resolution: between160 × 120 and 6144 × 4096

pixels(Sub sampling is4:0:0, 4:2:2, 4:2:0, 4:4:4)

Extremelylong and slender pictures maynot be

displayed.

*5 MPEG4datarecordedwiththePanasonicSD multi

cameras orDVD videorecorders conforming toSD

VIDEO specifications(ASFstandard) /MPEG4(Simple

Profile) videosystem/G.726 audiosystem

*6 Playsall versionsof DivX video(including DivX 6)

with

standardplayback of DivX mediafiles. Certifiedto

theDivX

Home Theater Profile.

GMC (Global Motion Compensation) not supported.

*7 Thetotal combinedmaximumnumber of recognizable

audio, picture and videocontentsand groups: 4000

audio, picture and videocontentsand 400 groups.

Videooutput:

Output level: 1Vp-p(75 )

Output terminal: Pinjack (1system)/AV

(DVD-S42EE)

Pinjack (1system)

(DVD-S42GC/GCA/GCS/GCU/

PLA/PL)

S videooutput:

Y output level: 1Vp-p(75 )

C output level: NTSC: 0.286 Vp-p(75 )

PAL: 0.300 Vp-p(75 )

(DVD-S42EE/GC/GCA/GCS/

GCU)

NTSC: 0.286 Vp-p(75 )

(DVD-S42PL/PLA)

Output terminal: AV

(DVD-S42EE)

S terminal (1system)

(DVD-S42GC/GCA/GCS/GCU/

PLA/PL)

Component videooutput:

[NTSC: (480)p/(480)i,

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

PAL: (576)p/(576)i]

(DVD-S42EE/GC/GCA/GCS/GCU)

[NTSC: (480)p/(480)i]

(DVD-S42PL/PLA)

Y output level: 1Vp-p(75 )

P B output level: 0.7Vp-p(75 )

P R output level: 0.7Vp-p(75 )

Output terminal: Pinjack (Y: green, P B : blue,

P R : red)

Number of terminals: 1system

RGB videooutput: (DVD-S42EE)

R output level: 0.7Vp-p(75 )

G output level: 0.7Vp-p(75 )

B output level: 0.7Vp-p(75 )

Output terminal: AV

Videoperformance:

Horizontal resolution: More than500 lines

VideoS/N ratio: More than65dB

Audiooutput:

Output level: 2Vrms (1kHz, 0dB)

Output terminal: Pinjack/AV

(DVD-S42EE)

Pinjack

(DVD-S42GC/GCA/GCS/GCU/

PL/PLA)

Number of terminals:

2channel: 1system

Audioperformance:

(1) Frequencyresponse:

DVD (linear audio): 4Hz-22 kHz (48 kHz sampling)

4Hz-44 kHz (96 kHz sampling)

CD audio: 4Hz-20 kHz

(2) S / N ratio:

CD audio: 115 dB

(3) Dynamicrange:

DVD (linear audio): 102 dB

CD audio: 98 dB

(4) Total harmonic

distortion:

CD audio: 0.003 %

Digital audiooutput:

Coaxial digital output: Pinjack

Pickup

Wavelength: 662 nm/ 785 nm

Laser power: CLASS 2/ CLASS 3A

Note:

Specificationsare subject tochangewithout notice.

Mass and dimensionsare approximate.

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Solder:

Thismodel uses leadfree solder (PbF).

Unauthorized copying and distribution isaviolation of law.

1. IMPORTANT SERVICE INFORMATION

1.1. Notes

Whenyou replace EEPROM orexchange MODULE P.C.B., you have totake "Manual for

customer" tothe customerwithunit.

(alsointhe case of unit exchange)

Please take and use "Manual forcustomer" frombelow.

1. Come with MODULE P.C.B. or EEPROM(Service part).

2. Make aphotocopysection 1.3. "Manual for customer" on this

service manual.

“Manual forcustomer” has important information for"DivX Video-on-Demand Service" user.

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Please don't forget take it tothe customerwithunit!

1.2. About DivX

1.2.1. DivX

A videocompression format developedbyDivXNetworks, Inc. that compresses videofiles

without anyconsiderable loss of videoquality.

1.2.2. About DivX Video-on-Demand Content

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

1.3. Manual for Customer

2. SAFETY PRECAUTIONS

2.1. GENERALGUIDELINES

1. When servicing, observe the original lead dress. Ifashort circuit

isfound, replace all parts which have been overheated or

damaged bythe short circuit.

2. After servicing, see to itthat all the protective devices such as

insulation barriers, insulation papers shields are properly

installed.

3. After servicing, make the following leakage current checks to

prevent the customer from being exposed to shock hazards.

2.1.1. LEAKAGE CURRENTCOLD CHECK

1. Unplug the AC cord and connect ajumper between the two

prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the

jumpered AC plug and each exposed metalliccabinet part on the

equipment such as screwheads, connectors, control shafts, etc.

When the exposed metallicpart has areturn path to thechassis,

the reading shouldbe between 1M and 5.2M . / When the

exposed metal does not have areturn path to the chassis, the

reading must be . Figure 1

2.1.2. LEAKAGE CURRENTHOTCHECK (See Figure 1 .)

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

1. Plug the AC cord directlyinto the AC outlet. Donot use an

isolation transformer for thischeck.

2. Connect a1.5k , 10 watts resistor, inparallel with a0.15 F

capacitors, between each exposed metallicpart on the set and a

good earth ground such as awater pipe, as shownin Figure 1.

3. Use an AC voltmeter, with 1000 ohms/voltor more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallicpart, and measure the voltage at

each point.

5. Reverse the AC plug inthe AC outlet and repeat each of the above

measurements.

6. The potential at anypoint shouldnot exceed 0.75 volts RMS. A

leakage current tester (Simpson Model 229 or equivalent) maybe

used to make the hot checks, leakage current must not exceed 1/2

milliamp. Incase ameasurement isoutside of the limits specified,

there isapossibilityof ashock hazard, and the equipment should

be repaired and rechecked before itisreturned to the customer.

3. PREVENTION OF ELECTRO STATIC DISCHARGE

(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)

DEVICES

Some semiconductor(solidstate) devices canbe damagedeasilybystatic electricity. Such

components commonlyare calledElectrostaticallySensitive (ES) Devices. Examples of typical

ES devices are integratedcircuits and some field-effect transistorsand semiconductor"chip"

components. The following techniques shouldbe usedtohelpreduce the incidence of

component damage causedbyelectrostatic discharge (ESD).

1. Immediatelybefore handling anysemiconductor component or

semiconductor-equipped assembly, drainoff anyESDon your

bodybytouching aknownearth ground. Alternatively, obtainand

wear acommerciallyavailabledischarging ESDwrist strap, which

shouldbe removed for potential shock reasons prior to applying

power to the unitunder test.

2. After removing an electrical assemblyequipped with ES devices,

place the assemblyon aconductive surface such as alminum foil,

to prevent electrostaticcharge buildup or exposure of the

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

assembly.

3. Use onlyagrounded-tipsoldering iron to solder or unsolder ES

devices.

4. Use onlyan anti-staticsolder removal device. Some solder

removal devices not classified as "anti-static(ESDprotected)"

can generate electrical charge sufficient to damage ES devices.

5. Donot use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ES devices.

6. Donot remove areplacement ES device from its protective

package until immediatelybefore you are readyto install it. (Most

replacement ES devices are packaged with leads electrically

shorted together byconductive foam, alminum foil or

comparableconductive material).

7. Immediatelybefore removing the protective material from the

leads of areplacement ES device, touch the protective material to

the chassisor circuitassemblyinto which the device will be

installed.

Caution

Besure no power isapplied to the chassisor circuit, and observe

all other safetyprecautions.

8. Minimize bodilymotions when handling unpackaged replacement

ES devices. (Otherwise hamless motion such as the brushing

together of your clothes fabricor the lifting of your foot from a

carpeted floor can generate staticelectricity(ESD)sufficient

todamage an ES device).

4. PRECAUTION OF LASER DIODE

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

5. SERVICE CAUTION BASED ON LEGAL

RESTRICTIONS

5.1. General description about Lead Free Solder (PbF)

The leadfree solderhas beenusedinthe mounting process of all electrical components on the

printedcircuit boards usedforthis equipment inconsidering the globallyenvironmental

conservation.

The normal solderis the alloyof tin(Sn) and lead(Pb). Onthe otherhand, the leadfree solderis

the alloymainlyconsists of tin(Sn), silver(Ag) and Copper(Cu), and the melting point of the

leadfree solderis higherapprox.30°C (86°F) more thanthat of the normal solder.

Definition of PCB LeadFree Solderbeing used

Service caution forrepairwork using LeadFree Solder(PbF)

-The lead free solder has to be used when repairing the equipment

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Altri manuali per DVD-S42EE

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Panasonic Lettore DVD

Panasonic

Panasonic DVDRV60 - Manuale utente

Panasonic

Panasonic DVD-LS80P Manuale utente

Panasonic

Panasonic DVD-RV45 Manuale utente

Panasonic

Panasonic DVD-XV10 Manuale utente

Panasonic

Panasonic CX-DV1500PEN Manuale utente

Panasonic

Panasonic DVD-H1000 Manuale utente

Panasonic

Panasonic DVD-S29GCS Manuale utente

Panasonic

Panasonic DVDPA65 - PORTABLE DVD Manuale utente

Panasonic

Panasonic DVD-A115U Manuale utente

Panasonic

Panasonic DVD-RV20 Manuale utente

Panasonic

Panasonic DVD-K32GCS Manuale utente

Panasonic

Panasonic DVD-S42PC Manuale utente

Panasonic

Panasonic DVD-F84 Manuale utente

Panasonic

Panasonic DVD-F61 Manuale utente

Panasonic

Panasonic SA-PM91DEE Manuale utente

Panasonic

Panasonic DVD-S1EE Manuale utente

Panasonic

Panasonic DVD-S31 Manuale utente

Panasonic

Panasonic DVD-RP62K Operating Manuale utente

Panasonic

Panasonic DVD-CP67K Operating Manuale utente

Panasonic

Panasonic DVD-S35E Manuale utente

Panasonic

Panasonic DVD-RV80 Manuale utente

Panasonic

Panasonic DVDS53 - DVD/CD PLAYER Manuale utente

Panasonic

Panasonic DVDRV31 - DIG. VIDEO DISCPLAYE Manuale utente

Panasonic

Panasonic CQDVR592U - AUTO RADIO/CD/DVD PL Manuale utente

Manuali Lettore DVD popolari di altre marche

Sony

Sony DVP-F11 Manuale utente

Philips

Philips DVP3560K/F8 Manuale utente

LENCO

LENCO DVP-740 X2 Manuale utente

JVC

JVC XV-N650BEU Manuale utente

Aiwa

Aiwa XD-DV370 Manuale utente

MedeaWiz

MedeaWiz Sprite 4K DV-S4 Manuale utente

Denon

Denon DVM-1805 - DVD Changer Manuale utente

Toshiba

Toshiba SD-3815 Manuale utente

Tevion

Tevion 44330 Manuale utente

Samsung

Samsung DVD-HD860 Manuale utente

Sylvania

Sylvania DP170SL8 Manuale utente

Toshiba

Toshiba SD-P1200 Manuale utente

JVC

JVC XV-D9000E Manuale utente

Dolby Laboratories

Dolby Laboratories CP650 Manuale utente

Philips

Philips DVD737K/931 Manuale utente

Denon

Denon DVD-5900 Manuale utente

Philips

Philips DVD 951 Manuale utente

Philips

Philips DVDR3460 Manuale utente