Panasonic TX-37LZ8F Manuale utente

Service Manual

Colour LCD Television

TX-37LZ8F

TX-37LZ8P

GLP23F Chassis

Specifications

Power Source: 220-240V AC, 50Hz

Power Consumption 162W

Stand-by Power Consumption: 0,8W

Aerial Impedance: 75Ωunbalanced, Coaxial Type

Receiving System: PAL-I/H, B/G, D/K,

SECAM B/G, D/K, L/L’

PAL-525/60 (AV only)

M.NTSC (AV only)

NTSC (AV input only)

Receiving Channels: VHF E2-E12 VHF H1-H2 (ITALY)

VHF A-H (ITALY) VHF R1-R2

VHF R3-R5 VHF R6-R12

UHF E21-E69 CATV (S01-S05)

CATV S1-S10 (M1-M10) CATV S11-S20 (U1-U10)

CATV S21-S41 (Hyperband)

Operating Conditions: Temperature: 0°C ÷35°C

Humidity: 20% − 80% RH (non condensing)

Scanning format: 480i(60Hz), 480p(60Hz), 576i(50Hz), 576p(50Hz), 720p(60Hz), 720p(50Hz), 1.080i(60Hz),

1.080i(50Hz), 1.080p(60Hz), 1.080p(50Hz), 1.080p(24Hz)

PC signals: VGA, WVGA, SVGA, XGA, WXGA (compressed)

Horizontal scanning frequency 31 – 69 kHz

Vertical scanning frequency 59 – 86 Hz

ORDER No. PCZ0810189CE

Unauthorized copying and distribu-

tion is a violation of law.

Intermediate Frequency:

Video/Audio

Video 38,9MHz, 33,9MHz

Audio 33,4MHz (B/G), 33,16MHz (A2)

33,05MHz (NICAM B/G, D/K, L)

32,4MHz (D/K), 32,66MHz (CZ STEREO)

40,4MHz (L’), 39,75MHz (L’NICAM)

Colour 34,47MHz (PAL)

34,5MHz, 34,65MHz (SECAM)

38,3MHz, 38,15MHz (SECAM L’)

Terminals:

AV1 IN Video (21 pin) 1V p-p 75Ω

Audio (21 pin) 500mV rms 10kΩ

RGB (21 pin) 0,7V p-p 75Ω

AV1 OUT Video (21 pin) 1V p-p 75Ω

Audio (21 pin) 500mV rms 1kΩ

AV2 IN Video (21 pin) 1V p-p 75Ω

Audio (21 pin) 500mV rms 10kΩ

RGB (21 pin) 0,7V p-p 75Ω

S-video IN (21-pin)Y: 1V p-p 75Ω

C:0,3V p-p 75Ω

AV2 OUT Video (21 pin) 1V p-p 75Ω

Audio (21 pin) 500mV rms 1kΩ

AV3 IN S-Video IN (4-pin) Y: 1V p-p 75Ω

C:0,286V p-p 75Ω

Audio (RCAx2) 500mV rms 10kΩ

Video (RCAx1) 1V p-p 75Ω

HDMI1, HDMI2 Type A Connector

COMPONENT Video (RCAx3) Y:1V p-p 75Ω(including synchronization)

Pb, Pr: ±0,35V p-p 75Ω

AUDIO IN Audio (RCAx2) 500mV rms 10kΩ(for HDMI1, COMPONENT-AUDIO)

AUDIO OUT Audio (RCAx2) 500mV rms 1kΩ(high impedance)

PC HIGH-DENSITY D_SUB 15PIN R,G,B: 700mV p-p 75Ω

HD,VD/TTL Level 2-5V p-p (high impedance)

LCD screen: L5EDD9T00008

1920 x 1080 XGA, 16:9

Visible Diagonal 940mm

Audio Output: 20W (2x10W)

Headphones: 3,5mm, 8ΩImpedance

Accessories supplied : Remote Control 2 x R6 (UM3) Batteries

Dimensions:

Height: Width: Depth:

Including TV stand 645mm 940mm 290mm

TV set only 605mm 940mm 110mm

Mass:

Including TV stand 21.0kg

TV set only 17.5kg

Specifications are subject to change without notice.

Mass and dimensions shown are approximate.

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not

contain warnings or cautions to advise non-technical individuals of potencial dangers in attempting to service a product. Products

powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the

product or products deal within this service information by anyone else could result in serious injury or death.

Warning

CONTENTS

SAFETY PRECAUTIONS........................................... 4

GENERAL GUIDE LINES...................................... 4

TOUCH – CURRENT CHECK............................... 4

PREVENTION OF ELECTROSTATIC DISCHARGE

(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)

DEVICES.................................................................... 5

ABOUT LEAD FREE SOLDER (PBF)......................... 6

SUGGESTED PB FREE SOLDER........................ 6

APPLICABLE SIGNALS.............................................. 7

SERVICE HINTS ........................................................ 8

CHASSIS BOARD LAYOUT....................................... 9

LOCATION OF LEAD WIRING………………………….9

SETTING INSPECTION............................................ 10

SELF-CHECK ........................................................... 11

ADJUSTMENT METHOD.......................................... 12

WIRING DIAGRAM................................................... 13

BLOCK DIAGRAMS.................................................. 14

PARTS LOCATION................................................... 17

REPLACEMENT PARTS LIST.................................. 19

SCHEMATIC DIAGRAMS......................................... 31

A-BOARD (1 OF 5) SCHEMATIC DIAGRAM...... 32

P-BOARD SCHEMATIC DIAGRAM .................... 36

G-BOARD SCHEMATIC DIAGRAM.................... 37

K-BOARD SCHEMATIC DIAGRAM .................... 38

V-BOARD SCHEMATIC DIAGRAM .................... 39

CONDUCTOR VIEWS .............................................. 40

Safety Precautions

General Guide Lines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated

or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

3. After servicing, make the following touch current checks to prevent the customer from being exposed to shock hazards.

4. Always ensure panel TKP0E16001 is correctly replaced before returning to customer (see Fig.1).

Touch-Current Check

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth

ground such as a water pipe, as shown in Fig. 2.

3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reserve the AC plug in the AC outlet and repeat each of the above measure.

6. The potential at any point (TOUCH CURRENT) expressed as voltage U1 and U2, does not exceed the following values:

For a. c.: U1 = 35 V (peak) and U2 = 0.35 V (peak);

For d. c.: U1 = 1.0 V,

Note:

The limit value of U2 = 0.35 V (peak) for a. c. and U1 = 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and

2.0 mA d. c.

The limit value U1 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100

kHz.

7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should

be repaired and rechecked before it is returned to the customer.

Fig. 2

APPLIANCES

EXPOSED

METAL PARTS

Resistance values in ohms (Ω)

R0=500

RS=1500

CS=0.22

10k

0.022

COLD

WATER PIPE

(EARTH GROUND)

V: Voltmetr or oscilloscope

(r.m.s. or peak reading)

Measuring network for TOUCH CURRENTS

Input resistance: ≥ 1M

Input capacitance: ≤ 200pF

Frequency range: 15Hz to 1MHz and d.c.respectively

NOTE – Appropriate measures should be taken to obtain the correct value in case of non-sinusoidal waveforms

U2(V)

Fig. 1

Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are

called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect

transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of

component damage caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on

your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD

wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge build up or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD

protected)" can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it.

(Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil

or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective

material to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity

(ESD) sufficient to damage an ES device).

There are special components used in this equipment which are important for safety.

These parts are marked by in schematic diagrams, exploded views and replacement parts list. It is essential that

these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do

not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work,

we’d suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol

stamped on the back of PCB.

Caution

•Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40°C)

higher. Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).

•Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before

applying Pb solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

•After applying PbF solder to double layered boards, please check the component side for excess solder which may

flow onto the opposite side. (see Fig.3)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.

However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used. (see Fig.4)

Fig.3

Fig.4

Applicable signals

Note:

•Signals other than above may not be displayed properly.

•The above signals are reformatted for optimal viewing on your display.

•Applicable input signal for PC is basically compatible to VESA standard timing.

•PC signal is magnified or compressed for display, so that it may not be possible to show fine detail

with sufficient clarity.

Signal name Horizontal frequency (kHz) Vertical frequency (Hz)

640 ×480 @70 Hz 31.47 70.07

640 ×480 @60 Hz 31.47 59.94

640 ×480 @75 Hz 37.50 75.00

800 ×600 @60 Hz 37.88 60.32

800 ×600 @75 Hz 46.88 75.00

800 ×600 @85 Hz 53.67 85.06

852 ×480 @60Hz 31.44 59.89

1,024 ×768 @60Hz 48.36 60.00

1,024 ×768 @70Hz 56.48 70.07

1,024 ×768 @75Hz 60.02 75.03

1,024 ×768 @85Hz 68.68 85.00

1,280 ×1024 @60Hz 63.98 60.02

1,366 ×768 @60Hz 48.39 60.04

Macintosh13” (640 ×480) 35.00 66.67

Macintosh16” (832 ×624) 49.73 74.55

Macintosh21” (1,152 ×870) 68.68 75.06

Signal name COMPONENT HDMI

525 (480) / 60i * *

525 (480) / 60p * *

625 (576) / 50i * *

625 (576) / 50p * *

750 (720) / 60p * *

750 (720) / 50p * *

1,125 (1,080) / 60i * *

1,125 (1,080) / 50i * *

1,125 (1,080) / 60p *

1,125 (1,080) / 50p *

1,125 (1,080) / 24p *

Component (Y, Pb, Pr), HDMI

PC (D-sub 15P)

Service Hints

How to remove the backcover

Remove the 14 fixing screws. (see Fig.5)

How to remove the Pedestal assembly

Lay the main unit face down. (see Fig.6)

Remove the 4 fixing screws and the pedestal assembly. (see Fig.7)

Fig.6

SCREWS SCREWS

Fig.5

Fig.7

SCREWS

Chassis Board Layout

Location of Lead Wiring

To find the Part Number of required wire in Replacement Parts List click on the wire name in red box.

Board Name Function

A-Board AV Terminal, Audio Video Processor, Speaker out, TV tuner,

HDMI, HDMI Receiver

G-Board Side AV Terminal

V-Board Remote Receiver, R&G LED, C.A.T.S.

K-Board Main Switch

P-Board Main Input, Power Supply, Power Supply Regulator

G-BOARD

A-BOARD P-BOARD

V-BOARD K-BOARD

A18

G51-A7

A5-SP

A8-V1

G51

TU101A

INVERTER

A5 P1

A18-Panel_LVDS

A16

A7 A8

A10

A16/P5-INVERTER

A4-K1

Setting Inspection

Voltage Confirmation

Confirm the following voltages:

A board

Description Test point Range

STBY1V TP1838 1,015-1,05V

STBY3,3V TP1840 3,14-3,47V

MAIN1V TP3832 1,0-1,05V

MAIN3,3V TP3833 3,13-3,47V

CORE1V TP1842 1,06-1,1V

MAIN2,5V TP1845 2,83-2,63V

MAIN1,8V TP1846 1,728-1,9V

MAIN1,25V TP1844 1,245-1,275V

MAIN5V TP3826 4,775-5,25V

STBY5V TP3813 4,9-5,4V

MAIN8V TP3823 7,6-8,4V

PANEL12V TP3824 11,97-12,81V

CEC3,8V TP3814 3,5-4,2V

TUNER30V TP3801 28-32V

TERMINATION TP3831 0,794-1,02

P board

Description Test point Normal condition Stand By

AUDIO VCC TP865 13,6V+/- 0,8V 0V

STB 5V6 TP853 5.65+/- 0,25V 5.65+/- 0,25V

24V IN TP856 24V+/- 1,5V 0V

Altri manuali per TX-37LZ8F

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Panasonic TV LCD

Panasonic

Panasonic TH-L32C3D Manuale utente

Panasonic

Panasonic VIERA TX-L65WT600B Manuale utente

Panasonic

Panasonic TX-32LX500M Manuale utente

Panasonic

Panasonic Viera TC-L32U22M Manuale utente

Panasonic

Panasonic TX-R32LX8 Manuale utente

Panasonic

Panasonic Viera TX-L32UX3E Manuale utente

Panasonic

Panasonic TX-23LX50M Manuale utente

Panasonic

Panasonic TX-L32DT35E Manuale utente

Panasonic

Panasonic TH-L42U30R Manuale utente

Panasonic

Panasonic TC-37LZ800 - 37" LCD TV Manuale utente

Panasonic

Panasonic Viera TC-L37C22 Manuale utente

Panasonic

Panasonic Viera TX-L32C20B Manuale utente

Panasonic

Panasonic Viera TX-L32U10B Manuale utente

Panasonic

Panasonic Viera TX-37LZD70F Manuale utente

Panasonic

Panasonic Viera TX-55AX902B Manuale utente

Panasonic

Panasonic Viera TH-L24X5A Manuale utente

Panasonic

Panasonic TC17LA1 - 17" LCD COLOR TV Manuale utente

Panasonic

Panasonic TC23LX60 - 23" LCD TV Manuale utente

Panasonic

Panasonic Viera TX-26LXD60A Manuale utente

Panasonic

Panasonic TX65CR730E Manuale utente

Panasonic

Panasonic TC-L32XM6L Manuale utente

Panasonic

Panasonic Viera TC-L55E50 Manuale utente

Panasonic

Panasonic TCL32U3 - 32" LCD TV Manuale di servizio

Panasonic

Panasonic Viera TC-L32C5 Manuale utente

Manuali TV LCD popolari di altre marche

LG 32LC4R* Manuale utente

ViewSonic

ViewSonic N4200w-1 VS10945-1M Manuale utente

Salora

Salora 22LED1600 Manuale utente

Samsung

Samsung LA32E420 Guida

Dell

Dell W1900 19 Istruzioni utente

Samsung

Samsung LN40C670M1F Manuale utente

Samsung

Samsung Series 4+ Manuale utente

Samsung

Samsung 5 Series Manuale utente

Grundig

Grundig 40 VLE 8230 BP Manuale utente

Philips

Philips 43PFL4901/F7 Manuale utente

Sony

Sony Bravia XBR-43X830C Manuale utente

LG 32LS350 Manuale utente

VIORE

VIORE LED32VF60 Manuale utente

Toshiba

Toshiba Regza 42HL167 Manuale utente

JVC

JVC LT-32A220 Manuale utente

Philips

Philips 20TA1000/93 Manuale utente

Philips

Philips 32PFL3158T/12 Manuale utente

Sony

Sony Bravia KDL-V32XBR2 Manuale utente