Panasonic SC-EN38GCS Manuale utente

AMPLIFIER SECTION

RMS

OUTPUT POWER both channel driven simultaneously

10%

total harmonic distortion (THD)

kHz 3 W per channel (6 Ω)

PMPO

Output Power 90 W

Input

Music Port

Sensitivity

100 mv, 15 kΩ

Terminal

Stereo, 3.5 mm jack

Output

Headphone

Terminal

Stereo, 3.5 mm jack

(16 Ωto 32 Ω)

Option

Port Version 1

TUNER SECTION

Frequency

range

87.50 MHz to 108.00 MHz

(50 kHz)

522 kHz to 1629 kHz (9 kHz)

520 kHz to 1630 kHz (10 kHz)

DISC SECTION

Disc

played [8cm or 12cm]

(1)

CD-Audio (CD-DA)

(2)

CD-R/RW (CD-DA, MP3)

(3)

MP3

Sampling

frequency

44.1 kHz

rights reserved. Unauthorized copying and

distribution is a violation of law.

SC-EN38GCS

Colour

(K)... Black Type

MP3 32 kHz, 44.1 kHz, 48 kHz

Bit rate

MP3 32 kbps to 384 kbps

Decoding 16/20/24 bit linear

Pick up

Wavelength 785 nm

Laser power CLASS 1

Audio Output (Disc)

Number of channels 2 channel

Audio performance

Frequency response (CD-Audio) 20 Hz to 20 kHz

Wow and flutter Below measurement limit

Digital filter 8

D/A converter MASH (1 bit DAC)

IUSB SECTION

Media file format support MP3 (*.mp3)

Power consumption in standby mode:

2.6 W (approx.)

ISPEAKER SECTION

Type 1 Way, 1 speaker system

(Bass reflex)

Speaker (s)

Full range 7 cm cone type

CD Stereo System

Specifications

ORDER NO. MD0804001CE

Impedance 6Ω

Input power (IEC) 3W(MAX)

Dimension (W x H x D) 120 mm x 202.8 mm x 133.5 mm

IGENERAL

Power supply AC 220 to 240 V, 50 Hz

Power consumption 30 W

Dimension (W x H X D) 252.5mm x 202.8mm x 133.5 mm

Mass

With speakers Approx. 3.20 kg

1 Safety Precautions 3

2 Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices 5

3 Precaution of Laser Diode 6

4 Handling Precautions For Traverse Deck 7

5 Handling the Lead free Solder 8

6 Accessories 9

7 Operation Procedures 10

8 Self diagnosis and special mode setting 14

9 Assembling and Disassembling 19

10 Service Fixture and Tools 46

Without speakers Approx. 1.90 kg

Operating temperature range 0°Cto+40°C

Operation humidity range 35% to 80% RH (no condensation)

Notes:

• Specifications are subject to change without notice.

• Total harmonic distortion is measured by the digital spectrum

analyzer.

ISystem : SC-EN38GCS-K Main Unit: SA-EN38GCS-K

Speaker: SB-EN38P-K

11 Service Position 47

12 Voltage Measurement & Waveform Chart 53

13 Wiring Connection Diagram 59

14 Block Diagram 61

15 Notes Of Schematic Diagram 65

16 Schematic Diagram 67

17 Printed Circuit Board 77

18 Illustration of IC’s, Transistors and Diodes 81

19 Terminal Function of IC’s 82

20 Exploded Views 85

21 Replacement Parts List 89

CONTENTS

Page Page

SC-EN38 GCS

1.1.2. Leakage Current Hot Check

1 Safety Precautions

1.1. General Guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

2. After servicing, ensure that all the protective devices such as insulation barriers, insulation papers shields are properly installed.

3. After servicing, check for leakage current checks to prevent from being exposed to shock hazards.

1.1.1. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Using an ohmmeter measure the resistance value, between the jumpered AC plug and each exposed metallic cabinet part on

the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the

chassis, the reading should be between 1MΩand 5.2Ω.

When the exposed metal does not have a return path to the chassis, the reading must be .

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a

good earth ground such as a water pipe, as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.

6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may

be used to make the hot checks, leakage current must not exceed 1/2 milliamp. should the measurement is outside of the limits

specified, there is a possibility of a shock hazard, and the equipment should be repaired and re-checked before it is returned

to the customer.

Fig. 1

SC-EN38 GCS

1.2. Before Repair and Adjustment

Disconnect AC power, discharge Power Supply Capacitors C501 through a 10Ω, 1W resistor to ground.

DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.

After repairs are completed, restore power gradually using a variac, to avoid overcurrent.

• Current consumption at AC 230-240 V, 50 Hz in NO SIGNAL mode should be ~300 mA.

1.3. Protection Circuitry

The protection circuitry may have operated if either of the following conditions are noticed:

• No sound is heard when the power is turned on.

• Sound stops during a performance.

The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are

"shorted", or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.

If this occurs, follow the procedure outlines below:

1. Turn off the power.

2. Determine the cause of the problem and correct it.

3. Turn on the power once again after one minute.

Note:

When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.

1.4. Safety Part Information

Safety Parts List:

There are special components used in this equipment which are important for safety.These parts are marked by in the

Schematic Diagrams & Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s

specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of manufacturer.

Table 1

Reference No. Part No. Part Name & Description Remarks

A2 K2CQ2CA00007 AC CORD [M]

A2 K2CP2CA00001 AC CORD [M]

JK600 K2AA2B000017 AC INLET [M]

T600 G4CYAYY00176 TRANSFORMER [M]

F1 K5D202BLA013 FUSE [M]

L600 ELF15N035AN LINE FILTER [M]

301 RAE0165T-V TRAVERSE UNIT (W/O CD SERVO

P.C.B)

[M] (RTL)

FP600 K5G302AA0002 FUSE PROTECTOR [M]

FP841 K5G251A00008 FUSE PROTECTOR [M]

R260 ERD2FCVG470T 47 1/4W [M]

PCB6 REPX0652F TRANSFORMER P.C.B [M] (RTL)

PCB7 REPX0652F AC INLET P.C.B [M] (RTL)

SC-EN38 GCS

2 Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage

caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equiped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equiped with ES devices, place the assembly on a conductive surface such as aluminium

foil, to prevent electrostatic charge build up or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder remover device. Some solder removal devices not classified as “anti-static (ESD protected)” can

generate electrical charge to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or

comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize body motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing

together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to

damage an ES device).

SC-EN38 GCS

3 Precaution of Laser Diode

Caution :

This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens.

Wavelength : 785 nm (CD)

Maximum output radiation power from pick up : 100 µW/VDE

Laser radiation from pick up unit is safety level, but be sure the followings:

1. Do not disassemble the optical pick up unit, since radiation from exposed laser diode is dangerous.

2. Do not adjust the variable resistor on the pick up unit. It was already adjusted.

3. Do not look at the focus lens using optical instruments.

4. Recommend not to look at pick up lens for a long time.

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

SC-EN38 GCS

The laser diode in the traverse deck (optical pickup) may break

down due to potential difference caused by static electricity of

clothes or human body.

So, be careful of electrostatic breakdown during repair of the

traverse deck (optical pickup).

GHandling of CD traverse deck (optical pickup)

1. Do not subject the traverse deck (optical pickup) to

static electricity as it is extremely sensitive to electrical

shock.

2. The short land between the No.4 (LD) and No.5 (GND)

pins on the flexible board (FFC) is shorted with a solder

build-up to prevent damage to the laser diode.

3. Take care not to apply excessive stress to the flexible

board (FFC board) (Fig 4.1).

4. Do not turn the variable resistor (laser power

adjustment). It has already been adjusted.

Fig 4.1

GGrounding for electrostatic breakdown prevention

1. Human body grounding (Fig 4.2)

Use the anti-static wrist strap to discharge the static

electricity from your body.

2. Work table grounding (Fig 4.2)

Put a conductive material (sheet) or steel sheet on the

area where the traverse deck (optical pickup) is placed,

and ground the sheet.

Caution :

The static electricity of your clothes will not be grounded

through the wrist strap. So, take care not to let your

clothes touch the traverse deck (optical pickup).

Fig 4.2

Caution when Replacing the Optical Pickup :

The traverse has a short point shorted with solder to protect

the laser diode against electrostatics breakdown. Be sure to

remove the solder from the short point before making

connections.

4 Handling Precautions For Traverse Deck

SC-EN38 GCS

5 Handling the Lead free Solder

5.1. General description about Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this

equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin

(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that

of the normal solder.

Definition of PCB Lead Free Solder being used

The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.

(See right figure)

Service caution for repair work using Lead Free Solder (PbF)

• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

• To put lead free solder, it should be well molten and mixed with the original lead free solder.

• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt

the lead free solder.

• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30

degrees C (662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01K-----------(0.3mm 100g Reel)

RFKZ06D01K-----------(0.6mm 100g Reel)

RFKZ10D01K-----------(1.0mm 100g Reel)

Note

* Ingredient: Tin (Sn), 96.5%, Silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

SC-EN38 GCS

Remote

control

AC cord

AC cord (For

Thailand only)

AM antenna

Support stand

AC Clamp

Filter

6 Accessories

Note : Refer to Packing Materials & Accessories (Section 21) for part number.

SC-EN38 GCS

7 Operation Procedures

7.1. Main Unit & Remote Control Key Buttons Operation

SC-EN38 GCS

Indice

Altri manuali Panasonic Impianto stereo

Panasonic

Panasonic RX-CT890 Manuale utente

Panasonic

Panasonic SC-EN37P Manuale utente

Panasonic

Panasonic SCPM71SD - MINI HES W/CD PLAYER Manuale utente

Panasonic

Panasonic SCAK220 - MINI HES W/CD PLAYER Manuale utente

Panasonic

Panasonic SC-PMX802 Manuale utente

Panasonic

Panasonic SC-VK650 Manuale utente

Panasonic

Panasonic SA-PMX3GN Manuale utente

Panasonic

Panasonic SH-FX85P Manuale utente

Panasonic

Panasonic SA-AK750GCP Manuale utente

Panasonic

Panasonic SC-EN38DB Manuale utente

Panasonic

Panasonic RXD15 - RADIO CASSETTE W/CD Manuale utente

Panasonic

Panasonic SC-HC395 Manuale utente

Panasonic

Panasonic SC-PM200 Manuale utente

Panasonic

Panasonic SC-CH72 Manuale utente

Panasonic

Panasonic SH-FX80 Manuale utente

Panasonic

Panasonic SC-CH150 Manuale utente

Panasonic

Panasonic SC-HC57 Manuale utente

Panasonic

Panasonic SC-AK403 Manuale utente

Panasonic

Panasonic SC-AK580 Manuale utente

Panasonic

Panasonic SCDV150 - MINISYS 5-D DVD CHGR Manuale utente

Panasonic

Panasonic SC-PM21 Manuale utente

Panasonic

Panasonic SC-TM760 Manuale utente

Panasonic

Panasonic SA-AK500P Manuale utente

Panasonic

Panasonic SCPM29 - MINI HES W/CD PLAYER Manuale utente

Manuali Impianto stereo popolari di altre marche

LG CM3330B Manuale utente

Sony

Sony SS-CEP50 Manuale utente

Cetacea Sound

Cetacea Sound CVS-II Manuale utente

Aiwa

Aiwa XR-H66MD Manuale utente

Denon

Denon UCD-250 Manuale utente

Sanyo

Sanyo DC-MX41i Manuale utente

Sharp

Sharp CD-ES600V Manuale utente

Exibel

Exibel BDX600-UK Manuale utente

Sanyo

Sanyo DC-F320 Manuale utente

Philips

Philips FWM583X Manuale utente

Sharp

Sharp CD-C462 Manuale utente

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Manuale utente

Aiwa

Aiwa XR-EM70 Manuale utente

Cyrus

Cyrus Lyric Manuale utente

Philips

Philips MCM159/98 Manuale utente

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Manuale utente

RCA

RCA RS3965SB Manuale utente

Sharp

Sharp XL-UH240 Manuale utente