Panasonic MC-E4051-00 Manuale utente

Order Number MAC0418001C2

Vacuum Cleaner

MC-E4051-00

Specifications are subject to change without notice for further improvement.

Matsushita Electric Industrial Co., Ltd

distribution is a violation of law.

1.2. Wire Management Drawing

NOTE:

For general servicing, it is necessary to eliminate pinching of any wire during reassembly. After servicing any electrical compo-

nent or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current leakage.

3 REPLACEMENT INSTRUCTIONS

3.1. Nozzle cover

3.1.1. Removal

1. Release the nozzle cover by rotating the nozzle cover

retainers to the UNLOCK position.

2. Rotate upward on the nozzle cover to remove it from the

nozzle base.

3.1.2. Installation

1. To replace the nozzle cover, make sure the nozzle cover

retainers are in the UNLOCK position.

2. Hook the front of the nozzle cover onto the nozzle base

and rotate downward.

3. Once inplace, rotate the nozzle cover retainers to the

LOCK position.

3.2. Beater Bar Assembly

Replacement

3.2.1. Removal

1. Remove the lower plate as outlined in the Nozzle cover

section.

2. Disconnect mains lead from electrical outlet. Press han-

dle release pedal and tilt the handle down so cleaner is

lying flat on the floor.

3. Position hands on beater bar. If the belt is still attached to

the beater bar, there will be tension on it.

4. Carefully lift the right end of the beater bar and then lift

the left end.

5. Remove the belt from the motor drive shaft.

3.2.2. Installation

1. Reinstall new belt if necessary.

2. To replace the beater bar assembly, place the belt around

the motor shaft.

3. Loop the other end of the belt over the belt pulley on the

beater bar.

4. Insert the beater bar by placing the rounded portion of the

end caps down into the slots in the nozzle base.

5. Press firmly, checking to see that each end is completely

inserted.

6. Check to see that the belt is centered on the belt pulley

and that the beater bar turns freely.

7. Replace nozzle cover.

3.3. Belt Replacement

3.3.1. Removal

1. Follow all of the removal instructions outlined in the

Beater Bar Assembly Replacement section.

3.3.2. Installation

1. Place the new belt around the motor shaft and follow the

installation instructions in the Beater Bar Assembly

Replacement section.

3.4. Handle Assembly Replacement

3.4.1. Removal

1. Insert the connector pipe into the tool holder.

2. Remove the dust cover.

3. Press the handle release button and rotate to the down

position.

4. Disconnect the wire leads, wire connectors, and wire tie,

if present.

5. Remove cord stopper.

6. Remove the handle retention clip.

7. Remove handle from body by twisting and pulling away

from unit.

3.4.2. Installation

1. Insert handle into body in the down position, make sure

handle release button is in proper position.

2. Reinstall handle retention clip.

3. Replace cord stopper.

NOTE: Never reuse a cord stopper. Always install a new

cord stopper whenever the old one is removed.

4. Reconnect wire leads, wire connectors and wire tie if

needed.

5. Reinstall dust cover. Care should be taken not to pinch

any wires.

NOTE: For general servicing, it is necessary to eliminate pinch-

ing of any wire during reassembly. After servicing any electrical

component or electrical enclosure, the unit should be reassem-

bled and checked for dielectric breakdown or current leakage.

3.5. Handle Release Assembly

Replacement

3.5.1. Removal

1. Remove handle from unit as describes above.

2. Separate the handle assembly by removing (14) fourteen

screws as illustrated in the Exploded View (Handle

Assembly)

3. Remove handle release button and spring.

3.5.2. Installation

1. Insert new button and spring if necessary. Make sure but-

ton is seated properly in grooves on Handle A.

2. Assemble handle by reversing order above.

3.6. Mains Lead Assembly Replace-

ment

3.6.1. Removal

1. Refer to Handle Assembly Replacement Section.

2. With handle removed from body disassemble handle by

removing fourteen (14) screws. Refer to Handle Assem-

bly Exploded View.

3. Remove handle release button and spring.

4. Remove damaged lead.

3.6.2. Installation

1. Replace damaged lead. carefully routing mains lead as

illustrated.

2. Reinstall handle as outlined in the handle installation sec-

tion.

3. Replace the cord stopper, the two (2) cord stopper screws

and the wire connectors.

NOTE: Never reuse a cord stopper. Always install a new cord

stopper whenever the old one is removed.

NOTE: For general servicing, it is necessary to eliminate pinch-

ing of any wire during reassembly. After servicing any electrical

component or electrical enclosure, the unit should be reassem-

bled and checked for dielectric breakdown or current leakage.

3.7. ON/OFF Switch Replacement

3.7.1. Removal

1. Remove the dust cover to expose the electrical connec-

tions of the ON/OFF switch.

2. Remove the insulated black wire lead from switch. Note

the location of the insulated lead when removing from

switch.

3. Remove uninsulated black wire from switch.

4. Remove the ON/OFF switch, (for ON/OFF switch replace-

ment) by depressing the switch retaining tabs while push-

ing up out of the dust compartment at the same time.

3.7.2. Installation

1. When re-connecting lead wires to ON/OFF switch make

sure the insulated lead is reconnected to its original loca-

tion as shown.

3.8. Motor Protector Replacement

3.8.1. Removal

1. Remove the dust cover.

2. Remove the motor protector cover, by releasing one of

the tabs that secure it to the dust compartment. Take care

not to break the tabs during removal.

3.8.2. Installation

1. Reinstall the motor protector and protector spring into the

dust compartment. Replace the motor protector cover by

applying pressure until both tabs snap into place.

NOTE: For general servicing, it is necessary to eliminate pinch-

ing of any wire during reassembly. After servicing any electrical

component or electrical enclosure, the unit should be reassem-

bled and checked for dielectric breakdown or current leakage.

3.9. Motor Assembly Replacement

3.9.1. Removal

1. Remove the dust cover by removing the eight (8) screws.

2. Remove the lower plate, beater bar assembly, belt, the

plastic shaft and the nozzle housing as instructed in the

respective removal sections.

3. Disconnect the motor leads and remove the motor.

Remove the motor support rubber (rear), noise suppres-

sor and the motor support rubber (front).

3.9.2. Installation

1. Place the motor back into the dust compartment with the

tabs on the motor support(rear)aligned parallel to the

front edge of the dust compartment.

2. Rewire per the Pictorial Wiring Diagram and Wiring Man-

agement Drawing.

3. Replace the dust cover and the eight (8) screws.

4. Replace the nozzle housing assembly, belt, beater bar-

beater bar assembly, and lower plate according to the

respective installation instructions.

Indice

Altri manuali Panasonic Aspirapolvere

Panasonic

Panasonic MC-CG985 Manuale utente

Panasonic

Panasonic MCV7721 - UPRIGHT VACUUM Manuale utente

Panasonic

Panasonic MC-CJ919 Manuale utente

Panasonic

Panasonic MCUG581 - PLATINUM UPRIGHT VAC Manuale utente

Panasonic

Panasonic MCV5744 - UPRIGHT VACUUM Manuale utente

Panasonic

Panasonic MC-CL575 Manuale utente

Panasonic

Panasonic MC-GG529-00 Manuale utente

Panasonic

Panasonic Quickdraw MC-V5725 Manuale utente

Panasonic

Panasonic MC-E4063K Manuale utente

Panasonic

Panasonic MC-UG223 Manuale utente

Panasonic

Panasonic MCV413 - COMMERCIAL VACUUM Manuale utente

Panasonic

Panasonic MC-BJ980 Manuale utente

Panasonic

Panasonic MC-CL575 Manuale utente

Panasonic

Panasonic MC-CG520 Manuale utente

Panasonic

Panasonic MC-GG233 Manuale utente

Panasonic

Panasonic MC-E3001-WP47 Manuale utente

Panasonic

Panasonic MCV7505 - UPRIGHT VACUUM Manuale utente

Panasonic

Panasonic MCGG773 - UPRIGHT VACUUM - MULTI LANGUAGE Manuale utente

Panasonic

Panasonic MC-YL623G147-AE Manuale utente

Panasonic

Panasonic MCUG728 Manuale utente

Panasonic

Panasonic MC-CG663 Manuale utente

Panasonic

Panasonic Ultra-Pro MC-V400 Manuale utente

Panasonic

Panasonic MC-UG614 Manuale utente

Panasonic

Panasonic MCV5330 - UPRIGHT VACUUM 12.0 Manuale utente

Manuali Aspirapolvere popolari di altre marche

Bissell

Bissell LittleGreen Proheat 1425 Series Manuale utente

NEFF

NEFF N17XH10 0 Series Manuale utente

LG A9 Series Manuale utente

Oreck

Oreck Cordless Captura BK51700 Series Manuale utente

Kogan

Kogan KAVACROBVWA Manuale utente

Kränzle

Kränzle VENTOS 50 ID Guida utente

EVVO

EVVO Ai35 Manuale utente

DeWalt

DeWalt DWH200D Manuale utente

Pontec

Pontec Pondomatic Vacuum Cleaner Manuale utente

Cleanmaxx

Cleanmaxx PC-P007E Manuale utente

Exido

Exido 240-114 Manuale utente

RIDGID

RIDGID WD1685AU0 Manuale utente

Ezviz

Ezviz RE4P Manuale utente

STG global

STG global TANVAC HDV3000 Manuale utente

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manuale utente

Factory

Factory M3340 Manuale utente

Shop-Vac

Shop-Vac VN92 SERIES Manuale utente

Nobles

Nobles 608669 Manuale del prodotto