Paradigm T560 Manuale utente
TREADMILL SERVICE MANUAL
T560/T561
Customer Support Services
SERVICE MANUAL
HS Consumer Treadmills
INTRODUCTION
OW TO USE SERVICE MANUAL AND CONTACT CUSTOMER SUPPORT SERVICES
This service manual is applicable to Treadmill T560,T561. Note: Information represents typical configuration and may
differ slightly from actual equipment. The ervice Manual provides recommendations of safe and efficient approaches
to various situations. This manual is separated into six sections.
INTRODUCTION
TABLE OF CONTENT
ection Ⅰ
TROUBLE HOOTING GUIDE
ection Ⅱ
OPERATING CON OLE
ection Ⅲ
“How To…” ERVICE AND REPAIR GUIDE
ection Ⅳ
ELECTRONIC OVERVIEW
WIRING BLOCK DIAGRAM
WIRING DIAGRAM AND PART LI T
ection Ⅴ
PART IDENTIFICATION
ection Ⅵ
MI CELLANEOU INFORMATION
Refer to TABLE OF CONTENTS for section topics.
When an operation problem occurs, refer to troubleshooting guide and diagnostic mode to isolate cause. When
applicable, guides are listed by problem symptom followed with suggestions of probable cause(s).
Once source of problem is identified, consult” How To…” guides for recommended repair procedures. “How To…”
sub-sections are organized by replacement part or assembly name. For convenience, sub-section lists recommended
“Tools Required” to complete specific function. Refer to PARTS IDENTIFICATION to identify proper name and number
of part to order for repair of equipment.
A reproducible FAX order claim form is given in COMMUNICATING BY TELEFAC IMILE for convenient ordering of
service parts.
To order, contact H Customer upport ervices.
Via FAX – 24 hrs/day, 7days/week.
Via telephone – Monday to Friday from 8:30 AM to 5:30 PM (GMT+8)
Via post – At address cited.
To speed H response to your needs, please provide the following information.
1. Model number
2. erial number
3. ymptom of problem
4. Part name and number to order (if known)
Before installing parts, review “How To…” and follow step by step procedures recommended to install parts safely and
efficiently. If you have questions or comments please telephone, FAX or write us. We are:
ealthstream Taiwan Inc. – CUSTOMER SUPPORT SERVICES
16-3, Zichiang 1st Road
Jhongli, Taoyuan 32063 Taiwan R.O.C.
HS Consumer Treadmill
TABLE OF CONTENTS
SECTION I TROUBLES OOTING GUIDE PAGE
MCB…………….…………..…………………………………….…………………………………….…………
2
CON OLE……………..…………………………………………………………………………..……………..
5
SECTION II OPERATING CONSOLE
T560 CON OLE…..……………………………….……………………...……………………………………..
2
T561 CON OLE…..……………………………….……………………...……………………………………..
7
ETUP AND DIAGNO TIC MODE
…………………………………………………………………….….
12
SECTION III OW TO…REPLACE
RUNNING BELT AND DECK……….…………..……………………………………………………………….
2
ADJU T RUNNING BELT TRACKING………………………………………………………………………...
4
ADJU T RUNNING BELT TEN ION…………………………………………………………………………..
5
MOTOR DRIVE BELT……………………………………………………………………………………………
6
DRIVE MOTOR…………………………………………………………………………………………………..
7
FRONT ROLLER…………………………………………………………………………………………………
8
REAR ROLLER…………………………………………………………………………………………………..
9
DECK CU HION ………………………………………………………………………………………………...
10
INCLINE MOTOR………………………………………………………………………………………………...
12
MOTOR CONTROLLER…………………………………………………………………………………………
15
MAIN FRAME MOVING WHEEL……………………………………………………………………………….
16
SECTION IV ELECTRONIC OVERVIEW AND WIRING DIAGRAMS
T560 CON OLE……………………………………………….………………………………….……………..
2
T560 MOTOR CONTROLLER PCB……………………………………………….…………….…………… 3
T560 BLOCK DIAGRAM….…………………………….……………………………………………………….
5
T560 WIRING DIAGRAM AND PART LI T (CE VER ION)………...………………………………...…….
6
T561 CON OLE……………………………………………….………………………………….……………..
8
T561 MOTOR CONTROLLER PCB……………………………………………….…………….…………… 9
T561 BLOCK DIAGRAM….…………………………….……………………………………………………….
11
T561 WIRING DIAGRAM AND PART LI T (CE VER ION)………...………………………………...…….
12
NOTE …………………………………………………………………………………………………………….
14
HS Consumer Treadmill
TABLE OF CONTENTS - Continued
SECTION V PARTS IDENTIFICATION
T560 LA/EXPLODED DRAWING.….………………………………………….……………………………….
2
T560/T561 LA/PART LI T…………………………………………………………………………..…….…… 3
NOTE …………………………………………………………………………………………………………….
6
SECTION VI MISCELLANEOUS INFORMATION
PREVENTIVE MAINTENANCE………………………………………………………………………………...
2
UNPACKAGING IN TRUCTION ……………………………………………………………………………..
3
IN TALLATION IN TRUCTION ……………………………………. ……………………………………… 4
T560/IN TALLATION IN TRUCTION ……………………………………………………………………….
5
LIFE FAX……….…………..……………………………………………………………………………………..
8
NOTE …………………………………………………………………………………………………………….
10
HS Consumer Treadmill
Section 1 1
Section I
SECTION I
TROUBLES OOTING GUIDE
HS Consumer Treadmill
TROUBLESHOOTING GUIDE
Section 1
2
(1)
MCB
Error
Code
Error category When it happens. Follow up and send the information to Healthstream R&D center
Safety key Check Safety key f it happens frequently.
Check safety key cable and switch. - Open the plastic and check.
Next check the signal cable between motor and console.
Change the console.
Er 01 Speed sensor Speed sensor is broken.
Main power relay is
broken(in the motor
controller).
Motor is broken or motor
wire is badly connected.
PWM circuit that is in
console is broken.
Main cable is damaged.
Turn off and on the power.
Push Start key to test the treadmill.
Warning : Do not step on the treadmill, it is very dangerous.
1) Check if motor is running for short time.
if NO.
Check motor wire connection, motor brush connection, motor itself.
Motor controller circuit or signal cable was broken.
PWM circuit that is in console was broken.
if YES
Speed sensor wire connection , or speed sensor was broken.
Speed sensor circuit that is in motor controller was broken.
Signal cable or console was broken.
HS Consumer Treadmill
TROUBLESHOOTING GUIDE
Section 1 3
Error
Code
Error category When it happens. Follow up and send the information to Healthstream R&D center
Er 02 Over speed When treadmill runs faster
than target speed. - Check
Power circuit.
When User kicks the
treadmill belt faster
intentionally.
Frequency is very low.
t usually happens during
workout(14Km/h to
16Km/H).
Turn off and on the power.
Start the treadmill and check if there are Error 41 or others.
Warning : Do not step on the treadmill, it is very dangerous.
Er 06 Memory EEPROM of console error,
eeprom problem or circuit
problem.
Frequency is very low.
Turn off and on again. f it happens continually , you have to change the
console.
Er 08 Angle switch Angle switch broken.
When the treadmill is
folded.
When Err 08 on the console, even if treadmill is not folded.
Check the cable connection first and then check the angle switch(motor
control board).
HS Consumer Treadmill
TROUBLESHOOTING GUIDE
Section 1
4
Error
Code
Error category When it happens. Follow up and send the information to Healthstream R&D center
Er 15 Under speed When treadmill runs
slower than target speed.
Motor is damaged.
AC input is lower than
normal value(lower than
210VAC), with heavy user.
Deck and belt condition is
not good.(Check silicone).
Turn off and on the power.
Push Start key to test the treadmill.
Warning : Do not step on the treadmill, it is very dangerous.
During testing, if motor makes electric howling noise.
Check the motor condition and motor wires are tightly connected.
Check the condition of deck and belt, if deck and belt are damaged
you have to change the deck and belt , and lubricate it with silicone.
Er 05
Er 51
Er 52
Er 53
Elevation Check incline sensor or
motor.
Err 51,Err 52,Err 53
happen during self test or
calibration.
Turn off and on the power.
Calibrate the elevation motor again and check the console value.
Push and hole 12%+ 6% keys together for 2seconds to calibrate the motor.
Then treadmill goes up and goes down to the bottom, please check the
value on the monitor.
t should be more than 190 at the top, and it should be less than 40 at the
bottom.
Check the error message.
Er 51, Er 52, Er 53 or no message.
Check the elevation motor runs or not, when you test it ?
Warning : Do not step on the treadmill, it is very dangerous.
f no error message,
Please send the value that is displayed of the LCD during calibration to
Healthstream R&D center.
You have to do calibration again, if you want to use the elevation function.
HS Consumer Treadmill
TROUBLESHOOTING GUIDE
Section 1 5
Error
Code
Error category When it happens. Follow up and send the information to Healthstream R&D center
Er 40
Er 41
Over
acceleration
Over
acceleration
Treadmill accelerates too
fast than normal.
t happens when the
speed is less than 8
Km/H.
Fatal error. Stop using
treadmill.
Power circuit could be
broken.
Same as Er 40,
but it happens at the
beginning of
workout.( During Start)
Turn off and on the power.
Start the treadmill and check the Error message again.
Check the motor runs or not , when you test it ?
Warning : Do not step on the treadmill, it is very dangerous.
HS Consumer Treadmill
TROUBLES OOTING GUIDE - Continued
Section 1
6
(2) TROUBLE S OOTING GUIDE
Problem
Potential cause Corrections
Treadmill
will not
start
1. Not plugged in
2. Safety tether key not
inserted
3. House circuit breaker
tripped
4. Treadmill circuit breaker
tripped
5. Switch on OFF
1. Plug into grounded outlet.
2. nsert safety tether key into console.
3. Reset or replace fuse.
4. Lubricate treadmill deck and reset.
5. Turn switch to ON
Running
belt slips
1. Running belt not tight
enough
2. Drive belt not tight enough
1. Adjust running belt tension
2. Adjust drive belt tension
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Paradigm Tapis roulant
