Paradox RTX3 Manuale utente
RTX3
Wireless Expansion
Module
V5.3
Reference and Installation Manual
Table of Contents
Specifications..........................................................................3
Hardware Compatibility...................................................... 3
Overview .................................................................................. 4
Description .............................................................................. 4
Features ................................................................................... 4
Installation .............................................................................. 6
Antenna Installation ............................................................ 7
System Reset ........................................................................... 7
LED Feedback ........................................................................ 8
Programming ......................................................................... 9
Programming RTX3 for Spectra SP Series Panels....... 9
Programming for EVO Series Panels...............................9
Programming Stand-Alone RTX3 Modules.................. 17
Firmware Upgrade................................................................ 20
Index .......................................................................................... 21
Specifications
Hardware Compatibility
Power input voltage: 12Vdc
Frequency: 433MHz or 868MHz
Sensitivity: -120 dBm
Current consumption: 50 mA
Dimensions and
Weight:
15cm x 16cm x 3cm (6in x 6.5in x 1.1in) / 24g
Operating
temperature:
0°C to 49°C (32°F to 120°F)
Humidity: 5 - 90%
PGM outputs: PGM1 and PGM2 - 150mA PGM transistor
outputs
PGM3 - form C relay output rated at 5A/28Vdc,
N.O./N.C. (PGM4 optional)
Range: Refer to the appropriate transmitter Instructions
Other: Di-pole antenna; Error Correction Algorithm
Approvals: EN50131-3: Security Grade 2, Environmental
Class II, Certification Body Intertek
For the latest information on product approvals,
visit our website at www.paradox.com
EVO Spectra SP Stand Alone
Zones 32 32 32
Remotes 32/96/999 32 32
Remote Control
Type
REM1
RAC1
REM2
RAC2
REM3
REM15
REM1
RAC1
REM2
RAC2
REM3
REM15
REM1
REM15
Wireless PGMs 8 16 -
Wireless Keypads - 8 -
Wireless Siren 8 4 -
Wireless Repeater - 2 -
PX8 Output Module - - 4
Page 4
Overview
This chapter provides an overview of the RTX3 Wireless Expansion Module
(“RTX3”), including the package contents provided with the RTX3, the
system features and an overview of the RTX3 components.
Description
The RTX3 is a 2-way, 32 zone
wireless expansion module which
enables EVO and Spectra SP Series
control panels to support wireless
hardware such as sirens, motion
detectors and remote controls.
Features
• Up to 32 wireless zones
• Support for REM1 / REM2 /
REM3/ REM15 / RAC1 / RAC2
remote controls
• Support for wireless PGMs
• Support for all Magellan
transmitters including 2WPGM
• Support for two RPT1 and eight
K32RF / K37 (SP Series only)
• Support for SR130 / SR150
Wireless Sirens and RPT1
Wireless Repeater (EVO and
SP Series)
• Support for PX8 Output Module
• In-field firmware upgrade
through BabyWare software via
serial or 4-wire connection
• RF jamming supervision
• Low battery, tamper and check-
in supervision
• Transmitter signal strength
display
• 3 PGM outputs and 1 optional
output
• Noise level test and indicator
Included Items
Antenna
Required/Optional Items
• Mounting hardware
• Optional 12Vdc external
power supply (PS17)
Compatibility
• EVO 192 / EVOHD control
panels
• Spectra SP series control
panels
Page 5
RTX3 Board and Connectors
The following graphic displays the RTX3 board and connectors.
Figure 1: RTX3 Board and Connectors
1. LED display (see LED
Feedback on page 8)
2. Firmware upgrade serial
connector (see Firmware
Upgrade on page 20)
3. Anti-tamper switch
4. PCB screw
5. Antenna
6. Mounting clips
7. Mode Programming button: Used
for programming Stand Alone
RTX3 modules (see Stand Alone
Programming on page 17 and
System Reset (see System Reset on
page 7)
8. Program connector: Connect the
keypad to the Program connector
to program in Stand Alone mode
9. Wiring slot
2
8
7
1
5
4
3
9
6
Page 6 Installation
Chapter 1: Installation
This section describes how to connect the RTX3.
The following diagram displays RTX3 installation.
Figure 2: RTX3 Installation
1. Control panel Digiplex connection.
Notes:
• When using the RTX3 as a stand-alone device: connect an external
12Vdc power supply to the RED and BLK terminals
• Battery backup is recommended
2. Use a relay if the current draw exceeds 150mA on PGM1 or PGM2.
Connect the RTX3’s RED connector to the relay’s RED connector, and the
RTX3’s PGM connector (PGM1 or PGM2) to the relay’s BLK connector.
3. Connect PGM3 and PGM4 to external power supplies if additional
power is required. A PS-817 is recommended. Connect the PGM’s N/O
connector to the external power supply’s “+” connection. Connect the
power supply’s “-” connector to the device’s “-” connector. Connect the
PGM’s COM connector to the device’s “+” connector.
Note: Write down the serial number of all wireless modules used with
the RTX3.
1
23
Installation Page 7
Antenna Installation
Secure the antenna to the ANT terminal connector as displayed below.
Note: A 433 MHz antenna is displayed.
Figure 3:Antenna Connection
System Reset
System Reset restores the RTX3 factory settings.
IMPORTANT: System Reset only functions during the first 30 seconds after
RTX3 power up.
To reset the system:
1. Press and hold the Programming button for 5 seconds.
The BUS RX LED flashes (see LED Feedback on page 8).
2. Release the button and press it again while the LED flashes to reset the
RTX3 default settings.
Page 8 Installation
LED Feedback
The following tables display LED feedback.
ERROR
Problem with the
module
BUS RX
Receiving from panel
BUS TX
Transmitting to panel
RF RX
Receiving wireless
RF TX
Transmitting wireless
R
G
G
G
Y
ERROR
BUS RX
BUS TX
Com fail: GRN/YEL
short / no data
R
ERROR
BUS RX
BUS TX
Com fail: too many
modules / wrong data
R
G
ERROR
BUS RX
BUS TX
Com fail: GRN/
YEL reversed
G
R
G
ERROR
BUS RX
BUS TX
Combus power
too low
R
Legend
R = Red
G = Green
Y = Yellow
= Off
= On
= Flashing
Programming Page 9
Chapter 2: Programming
This section describes how to program the RTX3 for Spectra SP series
control panels, EVO series control panels and for stand-alone installations.
Programming RTX3 for Spectra SP Series Panels
When connected to a Spectra SP Series control panel, RTX3 settings are
programmed through control panel programming sections. For detailed
instructions refer to the Spectra SP Series Programming Guide.
Notes:
• Programming for a Spectra SP series system requires K32 or K10V/H
keypads v2.0 or higher
• Only one RTX3 module can be connected to a Spectra SP Series panel
Programming for EVO Series Panels
Program RTX3 settings for EVO panels with either a keypad or BabyWare PC
software.
Programming RTX3 with a Keypad
When connected to an EVO panel, program RTX3 settings through the
keypad by entering Module Programming Mode.
To enter Module Programming mode:
1. Press and hold the [0] key.
2. Enter the [INSTALLER CODE].
3. Enter section [4003].
4. Enter the module [SERIAL NUMBER].
5. Enter the required [DATA].
Note:When used without a K641 or K641R keypad, enable EVO option [1]
in section [3029].
After Programming RTX3 for EVO Control Panels
Program the zones, PGMs, sirens and remote controls into the EVO panel.
Refer to EVO section [3034] and RTX3 section [001]*options [2] and [3] for
wireless transmitter supervision options. Requirement: Configure all
wireless sirens in an EVO system to a single RTX3.
Page 10 Programming
*For instructions on entering 3-digit RTX3 section numbers see RTX3
Programming Sections for EVO Panels on page 10.
RTX3 Programming Sections for EVO Panels
Section Feature Details
[001] Option
[1] Low battery
supervision
For RTX3 version 1.5 and higher, this
option is always on
ON: default
[2] Check-in
supervision OFF: default
[3]
Check-in
supervision time
interval
OFF: 24 hours (default)
ON: 80 minutes
[4] RF Jamming
supervision OFF: default
[5]
On-board
module tamper
supervision
OFF: default
[6] PGM1 initial
state
OFF: Normally Open (default)
ON: Normally Closed
[7] PGM2 initial
state
OFF: Normally Open (default)
ON: Normally Closed
[8] Transmit tamper
signal
OFF: RTX3 ignores tamper signal
(default)
ON: RTX3 reports tamper signal
[002] Remote Control Options
[1]
REM2 visual and
auditory
feedback
compatibility
options*
OFF: Old visual and auditory feedback
(Supported by REM2 v2.00 or
lower)
ON: New visual and auditory feedback
(default)
Note: Requires REM2 v2.01 and higher
Altri manuali per RTX3
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Paradox Hardware per computer
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
