Paradyne Compshere 3000 Series Manuale utente
1
3000-A2-GZ41-60 December 1999
Rear Connector Plate and Modular DSU V.35 Adapter
Installation Instructions
Document Number 3000-A2-GZ41-60
December 1999
Overview This document describes the installation procedure for the rear connector plate
(Feature Number 3000-F1-021) and the modular Data Service Unit (DSU) V.35
adapter.
A rear connector plate is used with a modular DSU or a COMSPHERE3800
Series modem which has gold contacts on the rear edge of its circuit card
(Figure 1). When the rear connector plate is installed in a COMSPHERE 3000
Series Carrier, you can remove the modular DSU or 3800 Series modem without
disturbing the DTE cables attached to the rear connector plate at the back of the
carrier.
The rear connector plate has two 25-pin DTE connectors. One is a an
EIA-232-D/V.24 connector and the other is an ITU-T V.35 connector. If your cable
requires a 34-pin V.35 interface, you must use a V.35 adapter plug (Figure 3) or
adapter cable.
Gold Contacts
Modular DSU 25-Pin
EIA-232-D
Connector
25-Pin
V.35
Connector
Backplane
Connector
Figure 1. A Modular DSU and Rear Connector Plate
2 3000-A2-GZ41-60
December 1999
Installing the Rear Connector Plate
Prior to installation, check the rear connector plate and V.35 adapter for damage.
If either is damaged, report this immediately to your shipper and your service
representative.
!HANDLING PRECAUTIONS FOR
STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from
damage due to electrostatic discharge (ESD) during normal operation.
When performing installation procedures, however, take proper static
control precautions to prevent damage to equipment. If you are not
sure of the proper static control precautions, contact your nearest
sales or service representative.
To install a DSU and its rear connector plate for the first time:
"Procedure
1. At the rear of the carrier, set the tab on the rear connector plate into one of
the slots on the carrier’s backplane (Figure 2). Make sure the rear connector
plate uses the same slot position intended for the DSU.
2. Loosely fasten the screw attached to the rear connector plate, allowing for
slight adjustment that may be needed when installing the DSU.
3. At the front of the carrier, hold the DSU vertically with the latch on its
faceplate in the open position. Then, insert the circuit card into the top and
bottom circuit card guides for the slot that contains the rear connector plate.
Slot
25-Pin V.35
Connectors
25-Pin
EIA-232-D
Connectors
Screw
Non-Modular Devices Model 3511 DSU Rear Connector Plates
Figure 2.Rear View of the COMSPHERE 3000 Series Carrier
496-15104
3
3000-A2-GZ41-60 December 1999
4. Aligning the circuit card with the rear connector plate, slide the DSU into the
slot until the connectors seat firmly into the back of the carrier.
5. Press the faceplate latch to secure the DSU in the carrier, rotate the circuit
pack lock into the closed position, and tighten the screw.
6. Return to the rear of the carrier and tighten the rear connector plate screw.
7. At the rear of the carrier, connect the DTE to the rear connector plate
(see Figure 2):
—If you are using an EIA-232-D interface cable, connect the EIA-232-D
cable to the top DTE connector on the rear connector plate.
—If you are using a V.35 cable with a 34-pin connector, use the V.35
adapter as described in the next procedure.
Connecting to a 34-Pin V.35 Interface
To connect the V.35 adapter plug or V.35 adapter cable:
"Procedure
1. Connect the 25-pin end of the V.35 adapter plug or cable to the bottom DTE
connector on the rear connector plate. Tighten the screws on both sides of
the adapter.
2. Connect the DTE’s V.35 cable to the V.35 adapter plug or cable. Tighten the
screws on both sides of the cable connector.
3. If a ferrite choke was supplied with your DSU, install it on the adapter cable if
present, or on the V.35 cable as close as possible to the adapter plug.
Secure the ferrite choke in position, if necessary, with a cable tie.
25-Pin Connector
V.35 Adapter
V.35 Cable
Thumbscrews
99-16298
Figure 3. V.35 Adapter Plug Installation
4 3000-A2-GZ41-60
December 1999
Table 1 lists the pin assignments for the rear connector plate and the V.35
adapters.
Table 1. Rear Connector and V.35 Adapter Pin Assignments
25-Pin Connector
on Rear
Connector Plate
34-Pin
Connector on
V.35 Adapter Circuit Name
7
4
5
6
8
20
21
18
19
24, 11
23, 22
15, 2
16, 3
14, 1
9
10
25
B
C
D
E
F
H
J
L
N
P, S
R, T
U, W
V, X
Y, AA
HH
KK
NN
Signal Ground
Request-to-Send (RTS)
Clear-to-Send (CTS)
Data Set Ready (DSR)
Received Line Signal Detect (RLSD)
Data Terminal Ready (DTR)
Ring Indicator (RI)*
Local Loopback (LL)
Remote Digital Loopback (RL)
Transmitted Data (TXD)
Received Data (RXD)
Transmitter Signal Element Timing –DTE Source
Receiver Signal Element Timing –DCE Source
Transmitter Signal Element Timing –DCE Source
Positive dc Test Voltage
Negative dc Test Voltage
Test Mode (TM)
* Ring Indicator is available only on a DMB-S or a DBM-V.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor
directly for any help needed. For additional information concerning warranty,
sales, service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:
HInternet: Visit the Paradyne World Wide Web site at www.paradyne.com.
(Be sure to register your warranty at www.paradyne.com/warranty.)
HTelephone: Call our automated system to receive current information by fax
or to speak with a company representative.
—Within the U.S.A., call 1-800-870-2221
—Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail
them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N.,
number and title of this document in your correspondence. Please include your
name and phone number if you are willing to provide additional clarification.
*3000-A2-GZ41-60*
*3000–A2–GZ41–60*
Copyright E1999 Paradyne Corporation
Altri manuali per Compshere 3000 Series
4
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Paradyne Adattatore
Paradyne
Paradyne 7612 SNMP DSU Manuale di installazione
Paradyne
Paradyne 7612 Manuale utente
Paradyne
Paradyne ACCULINK 3150 Manuale
Paradyne
Paradyne 6512 Istruzioni operative originali
Paradyne
Paradyne 6512 Manuale utente
Paradyne
Paradyne 6512-A2 Manuale utente
Paradyne
Paradyne 9000 Series Manuale utente
Paradyne
Paradyne 3151 Manuale del proprietario
Paradyne
Paradyne 3100 Series Istruzioni operative originali
Paradyne
Paradyne 7612 Manuale di installazione
Paradyne
Paradyne SuperLine 6511 Istruzioni operative originali
Paradyne
Paradyne SuperLine 6502 Istruzioni operative originali
Paradyne
Paradyne 3151 Manuale utente
Paradyne
Paradyne 3151 Manuale utente
Paradyne
Paradyne 6512 Manuale utente
Paradyne
Paradyne 6512 Istruzioni operative originali
Paradyne
Paradyne ACCULINK 3150 Manuale
Paradyne
Paradyne 6512 Manuale utente
Paradyne
Paradyne 3100 Series Manuale utente
Paradyne
Paradyne ACCULINK 3150 Manuale di istruzioni
