Paradyne Hotwire 6390 Manuale utente

6390-A2-GK40-00 September 2002 1

Hotwire®ReachDSL™Modem, Model 6390

with Inline Phone Filter

Installation and Operation Supplement

Document Number 6390-A2-GK40-00

September 2002

Contents

Hotwire 6390 ReachDSL Modem Overview ...................................................... 2

Hotwire ReachDSL System ......................................................................... 3

Power-On ........................................................................................................... 4

Status LEDs ................................................................................................ 4

Troubleshooting ................................................................................................. 5

Increasing the Number of End-User Systems ................................................... 6

Optional ReachDSL Modem Wall Placement .................................................... 8

ReachDSL Modem Hardware Template ...................................................... 9

Hotwire 6390 ReachDSL Modem Commands ................................................... 10

Downloading Hotwire 6390 ReachDSL Modem Software ................................. 11

Building a Management PVC to the Model 8355 Line Card in an 8820

GranDSLAM Network .................................................................................. 12

Building a Management PVC through the 4200 GranDSLAM System ........ 14

Downloading Software to the ReachDSL Modem ....................................... 15

Technical Specifications for Hotwire 6390 ReachDSL Modem .......................... 16

2September 2002 6390-A2-GK40-00

Hotwire 6390 ReachDSL Modem Overview

The Hotwire®6390 ReachDSL™Modem is a component in the Hotwire

ReachDSL System and interoperates with the Hotwire 8355 ReachDSL Card in

the Hotwire 8820 GranDSLAM™system and in the 4200 GranDSLAM system.

The GranDSLAM system provides high-speed Internet or corporate LAN access

over traditional twisted-pair copper telephone wiring.

The ReachDSL technology:



Operates over existing copper wire with existing telephone jacks.



Uses an inline phone filter on the modem’s PHONE jack.



Includes a second line pass-through from the ReachDSL modem’s LINE jack

to PHONE jack to accommodate an attached 2-line telephone.



Provides adaptive data rates to dynamically adapt and allocate bandwidth to

optimize applications.

Refer to the

Hotwire ReachDSL Modem, Model 6390 with Inline Phone Filter,

Installation Instructions,

Document Number 6390-A2-GN10, for instructions on

how to install the Hotwire 6390 ReachDSL Modem.

6390-A2-GK40-00 September 2002 3

Hotwire ReachDSL System

Copper pairs run from the central office (CO) to the customer premises (CP) to

create the local loop. The local loop terminates on the customer premises at the

demarcation point.

NOTES:

In this document:

—A telephone is used to represent any equipment that plugs into a phone

jack and uses the POTS line, such as a phone, modem, or fax machine.

—End-user system is used to represent any PC with an Ethernet connection

and ReachDSL-based service.

—RJ11 wall jack is used to represent either an RJ11 or an RJ14 wall jack.

The RJ14 wall jack is used for a phone with two lines.

—Service provider is used to represent any Internet Service Provider (ISP)

or remote LAN access provider.

02-17237

ReachDSL

Modem

Customer Premises (CP)

DSL/POTS

Standard

Ethernet

Cable

Central

Office

(CO) Local Loop

Hub

DSL –Digital Subscriber Lines

POTS –Plain Old Telephone Service

End-user

Systems

Network

Service

Provider

(NSP) Demarcation

Point

Filter

Standard

Ethernet

Cable

4September 2002 6390-A2-GK40-00

Power-On

When power is applied, the ReachDSL modem performs self-diagnostics and the

PWR LED is on. The self-diagnostics includes a power-on self-test and all of the

LEDs turn on for one second.

Status LEDs

All of the LEDs turn on and off during the power-on self-test. After a successful

self-test, the LEDs should appear as indicated in BOLD in the Condition column

below.

Refer to

Troubleshooting

on page 5 for LED indications requiring action.

ReachDSL

TST LINE ETHERNET

ALMPWR TX/RX

01-17003

Power –green

Alarm –red

Test –yellow

Transmit/Receive –green

Ethernet Link –green

DSL Line –green

LED Condition Status

PWR ON ReachDSL modem has power.

ALM OFF

No active alarms.

An alarm condition exists.

TST OFF

No active tests.

The TST LED is on during the power-on self-test and during a

test initiated by the service provider.

LINE ON

OFF

The DSL link is active and ready to transmit and receive data.

The DSL link has not been established.

TX/RX ON

OFF

Data transmission is in progress on the DSL line.

The modem is not transmitting or receiving data.

ETHERNET ON

OFF

The Ethernet connection to the Ethernet hub or PC is active.

No Ethernet 10BaseT device is detected.

6390-A2-GK40-00 September 2002 5

Troubleshooting

To improve data transmission throughput and minimize background noise during a

telephone conversation, make sure that:



The Hotwire 6390 ReachDSL Modem is always powered on, even when not in

use, and



A Hotwire phone filter is installed on every telephone on the same line as the

Hotwire 6390 ReachDSL Modem (refer to the

Hotwire ReachDSL Modem,

Model 6390 with Inline Phone Filter, Installation Instructions,

Document

Number 6390-A2-GN10).

LED Symptom Action

All LEDs are on. If LEDs remain on after ten minutes, the modem is not functional.

Contact the service provider.

ALM LED remains

on. The power-on self-test may have failed. Unplug the unit and

reapply power. If the alarm LED is still on, contact the service

provider.

Ethernet LED is off. Verify thatthe Ethernet cable is securely installedat both ends, and

at least one PC is connected and powered on.

Verify that the correct straight-through or crossover cable is

installed. Refer to

Cables & Connectors

on page 6.

LINE LED is off. Verify that the DSL LINE cable is securely installed on both ends. If

the problem continues, contact the service provider.

Verify that the line has dial tone. If there is no dial tone, contact the

service provider.

LINE LED is on and

there is no data

transmission.

The DSL link has been established but there is no data

transmission. Verify the Ethernet connection. If the problem

persists, contact the service provider.

LINE and Ethernet

LEDs are on and

there is no data

transmission.

The DSL and Ethernet links have been established but there is no

data transmission. If the problem continues, contact the service

provider.

PWR LED is off. Check that the power cord is securely installed on both ends.

If no LEDs are on, the power supply may be defective. Test the

outlet to verify power. If the problem persists, contact the service

provider.

If other LEDs are on, the PWR LED may be burned out. Unplug the

unit and reapply power; watch all LEDs during the power-on

self-test to verify if the PWR LED is functioning.

TST LED is on. A test initiated by the service provider may be active. Wait five

minutes. If the TST LED does not go off, contact the service

provider.

6September 2002 6390-A2-GK40-00

Increasing the Number of End-User Systems

A single end-user system is attached to the Hotwire 6390 ReachDSL Modem by

using an Ethernet straight-through cable. To increase the number of end-user

systems, connect all the PCs to an Ethernet hub and connect the modem to the

hub’s uplink port using a standard straight-through cable for both connections.

The Hotwire ReachDSL port card supports 32 hosts/subnets per DSL port and the

Hotwire ReachDSL Modem supports up to 256 MAC entries.

Cables & Connectors

Standard twisted-pair CAT3 or better cables are recommended.



The LINE and PHONE interface connectors

use 6-pin, non-keyed modular plugs. RJ11 or

RJ14 6-pin connectors can be used.

Line & Phone Connectors



The LINE and PHONE jack pinouts are either filtered or unfiltered for POTS.

Pin # Function

1 Not used

2 Ring 2 (optional)

3 DSL Ring 1

4DSLTip1

5 Tip 2 (optional)

6 Not used

PHONE Jack Pinouts LINE Jack Pinouts

Pin # 3, 4 Filtered for POTS Pin # 3, 4 DSL and POTS

Pin # 2, 5 2nd POTS unfiltered Pin # 2, 5 2nd line pass-through

98-15304a

6-Pin

RJ11 Plugs

Pin #1

Pin #6

6390-A2-GK40-00 September 2002 7



The Ethernet interface connector uses an 8-pin, non-keyed modular plug. To

connect the DSL modem to an uplink port on an Ethernet hub or PC with an

Ethernet NIC card, use the straight-through connection.

8-Pin Straight-through Connection

Pin # Function

1 10BaseT RXD+

2 10BaseT RXD–

3 10BaseT TXD+

4 & 5 Not used

6 10BaseT TXD–

7 & 8 Not used

98-16055a

8-Pin

Plug

Ethernet

Cable

Pin #1

Pin #8

8September 2002 6390-A2-GK40-00

Optional ReachDSL Modem Wall Placement

The Hotwire 6390 ReachDSL Modem is designed for tabletop placement. The

modem can also be mounted on a wall. To mount the modem, you will need:

❑Two slotted-head #6 self-threading screws with plastic anchors

❑Drill and 3/16" drill bit for the plastic anchors

❑Screwdriver

A template with the dimensions for the two screws is provided. See

ReachDSL

Modem Hardware Template

on page 9.

Procedure

To mount the Hotwire 6390 ReachDSL Modem:

1. Use a drill to install the plastic anchors.

2. Use a screwdriver to install the screws. Do not install the screws flush with the

wall. Leave enough clearance to hang the modem housing from the screws.

Wall

Fasteners

01-17004

Hotwire

ReachDSL

Modem

6390-A2-GK40-00 September 2002 9

ReachDSL Modem Hardware Template

12.95 cm

5.10"

02-17014-01

Top

Bottom

10 September 2002 6390-A2-GK40-00

Hotwire 6390 ReachDSL Modem Commands

The Hotwire 6390 ReachDSL Modem provides the commands listed in Table 1,

Hotwire ReachDSL 6390 Modem Commands. Use a PC connected to the

Ethernet jack on the rear panel of the modem or Telnet into the modem to enter

these commands.

Table 1. Hotwire ReachDSL 6390 Modem Commands (1 of 2)

Command Syntax Argument Function Description

help {all<command>}



No argument



all



command

Displays help information.



Displays a list of all valid commands



Displays a list of all valid commands and

their syntax



Displays syntax for command

info None Displays device information.



Model Number



Serial Number



Firmware Revision



Hardware Revision



DSP Revision

logoff None Terminates the Telnet session.

mgmtpvc {dhcp<IP address>

<gateway>}



No argument



dhcp or ip address

–dhcp

Example: mgmtpvc dhcp

–IP address gateway

Example: mgmtpvc

135.26.95.1 135.26.95.6

Configures or displays the management PVC.



Current configuration



Configures the management PVC:

–The management PVC acquires its

address using DHCP

–The management PVC is configured for

the specified IP address and gateway

password [<login>] <password>



Example: password user user



password

Example: password secret

Configures the modem’s password(s).



Only available to “admin”users. Can either

be “admin”(default) or “user”



password

ping



Example: ping 135.26.12.254

Only available to “admin”users. Initiates a ping

to the specified IP address and displays

results.



An IP address must be specified

reset None Resets the unit.

Altri manuali per Hotwire 6390

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Paradyne Modem

Paradyne

Paradyne COMSPHERE 3800PLUS Manuale utente

Paradyne

Paradyne KeepInTouch 3766 Manuale utente

Paradyne

Paradyne COMSPHERE 3800PLUS Manuale utente

Paradyne

Paradyne Hotwire 7985 Manuale utente

Paradyne

Paradyne COMSPHERE 3810 Istruzioni per l'installazione

Paradyne

Paradyne COMSPHERE 3830 Manuale utente

Paradyne

Paradyne 2001 Manuale di istruzioni

Paradyne

Paradyne Hotwire 8775 Manuale utente

Paradyne

Paradyne COMSPHERE 3821PLUS Manuale utente

Paradyne

Paradyne COMSPHERE 3800PLUS Manuale di istruzioni

Paradyne

Paradyne COMSPHERE 3821PLUS Manuale utente

Paradyne

Paradyne HotWire 7914 Manuale utente

Paradyne

Paradyne COMSPHERE 3920PLUS Series Istruzioni per l'uso e l'installazione

Paradyne

Paradyne COMSPHERE 3800PLUS Manuale utente

Paradyne

Paradyne COMSPHERE 3800 Series Manuale per l'uso e la cura

Paradyne

Paradyne COMSPHERE 3921PLUS Manuale utente

Paradyne

Paradyne CopperJet 810 Manuale utente

Paradyne

Paradyne COMSPHERE 3920PLUS Series Manuale utente

Paradyne

Paradyne COMSPHERE 3810 Manuale del proprietario

Paradyne

Paradyne 6310 Manuale utente

Paradyne

Paradyne HotWire 7915 Manuale utente

Paradyne

Paradyne HotWire 7915 Manuale di istruzioni

Paradyne

Paradyne COMSPHERE 3920PLUS Series Manuale utente

Paradyne

Paradyne COMSPHERE 3800PLUS Manuale utente

Manuali Modem popolari di altre marche

Davicom

Davicom DM562AP Manuale utente

EpiValley

EpiValley TATA indicom SXC-1080 Manuale utente

Zte

Zte WiMAX Manuale utente

Intelimax

Intelimax MA-2060 Manuale utente

SMC Networks

SMC Networks D3CM1604V Manuale per l'uso e la cura

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuale utente

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuale utente

Samsung

Samsung AceLink SAM-335A Manuale utente

Enfora

Enfora Enabler-G Guida rapida alla configurazione

iRZ

iRZ ATM2-232 Manuale utente

Zhone

Zhone 6310 Manuale utente

US Robotics

US Robotics 3453C Manuale utente

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuale utente

Zte

Zte MF823 Manuale utente

Four-Faith

Four-Faith F1403 Manuale utente

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuale utente

Gemtek

Gemtek WiMAX WIXFBR-103 Manuale utente

Zoom

Zoom 1070 Series Manuale utente