Parker AC30V Series Manuale utente

AC30V series

Pump Control Application (US units)

HA502134U005 Issue 1

Technical Manual

aerospace

climate control

electromechanical

ﬁltration

ﬂuid & gas handling

hydraulics

pneumatics

process control

sealing & shielding

ENGINEERING YOUR SUCCESS.

www.comoso.com

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS

CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.

This document and other information from Parker Hannin Corporation, its subsidiaries and authorized distributors provide product or

system options for further investigation by users having technical expertise.

The user, through its own analysis and testing, is solely responsible for making the nal selection of the system and components

and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user

must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in

the current product catalogue and in any other materials provided from Parker Hannin Corporation or its subsidiaries or authorized

distributors.

To the extent that Parker Hannin Corporation or its subsidiaries or authorized distributors provide component or system options based

upon data or specications provided by the user, the user is responsible for determining that such data and specications are suitable

and sufcient for all applications and reasonably foreseeable uses of the components or systems.

The above disclaimer is being specically brought to the user’s attention and is in addition to and not in substitution to the Exclusions

and Limitations on Liability which are set out in the terms and conditions of sale.

www.comoso.com

Pump Control Application (US units)

HA502134U005 Issue 1



All rights strictly reserved. No part of this document may be stored in a retrieval system, or transmitted in any form or by any means to persons not employed by a Parker Hannifin

Manufacturing Limited company without written permission from Parker Hannifin Manufacturing Ltd. Although every effort has been taken to ensure the accuracy of this document it

may be necessary, without notice, to make amendments or correct omissions. Parker Hannifin Manufacturing Limited cannot accept responsibility for damage, injury, or expenses

resulting therefrom.

WARRANTY

Refer to Parker Hannifin Manufacturing Limited Terms and Conditions of Sale. These documents are available on request at www.parker.com.

Parker Hannifin Manufacturing Limited reserves the right to change the content and product specification without notice.

www.comoso.com

2 Pump Control (US units) Application Manual

AC30V series Variable Speed Drive

Pump Control (US units) Application Manual

Description

The pump application provides either flow control or speed control of a water pump.

In AUTO mode a flow feedback transducer is used to close the loop using a PID trim.

In MANUAL mode the requested pump speed is derived directly from the flow setpoint.

The calculated load is used to detect abnormal behaviour indicating blockage or leakage.

Feedback break input detection (4..20mA only).

Features

•Pump application specific menus and parameters

•Flow parameters and diagnostics in US Gallons / minute

•Pump Displacement in Cubic Inches

•PID flow control

•Automatic pump blockage and leakage detection (abnormal load)

•Power-up start

Requirements

To use the AC30V for pump control with US units as described in this manual, the application RA502134U005 must be loaded into an AC30V

series drive with firmware 1.4.1. or newer.

www.comoso.com

Pump Control (US units) Application Manual 3

AC30V series Variable Speed Drive

www.comoso.com

4 Pump Control (US units) Application Manual

AC30V series Variable Speed Drive

Inputs

Terminal Function Comment

ANIN 01 (X11/01) FLOW FEEDBACK Flow feedback input (0..10V, 0..20mA, 4..20mA)

ANIN 02 (X11/02) FLOW SETPOINT Flow setpoint input (0..10V)

DIGIN 01 (X13/02) MANUAL RUN Drive start with no PID control (speed control)

DIGIN 02 (X13/03) AUTO RUN Drive start with PID control (flow control)

DIGIN 03 (X13/04) AUTO SELECT Switch between AUTO and MANUAL modes

DIGIN 04 (X12/01) RUN ENABLE Auxiliary start signal

DIGIN 05 (X12/02) NOT COAST STOP Quench drive output

DIGIN 07 (X12/04) Terminal used as DIGOUT 01

DIGIN 06 (X12/03) Terminal used as DIGOUT 02

Outputs

Terminal Function Comment

ANOUT 01 (X11/03) PUMP SPEED DEMAND Pump speed demand as a percentage of maximum pump speed

ANOUT 02 (X11/04) PUMP LOAD Estimated load

RELAY 01

(X14/01 & X14/02) RUNNING When closed the pump is being driven

RELAY 02

(X14/03 & X14/04) NOT TRIPPED When closed the drive is not tripped

DIGOUT 01 (X12/01) Terminal used as DIGIN 04

DIGOUT 02 (X12/02) Terminal used as DIGIN 05

DIGOUT 03 (X12/03) LOAD WARNING Abnormal load (high or low) detection warning (blocked or leaking))

DIGOUT 04 (X12/04) LOAD FAULT Abnormal load (high or low) detection fault (blocked or leaking))

www.comoso.com

Pump Control (US units) Application Manual 5

AC30V series Variable Speed Drive

Graphical Keypad (GKP) Application Customisation

The pump application adds parameters and menus to the GKP. It also modifies the behaviour of the Control Screen and set-up wizard.

Control Screen

In Remote (terminal or comms) mode In Local (GKP) mode

1951:Flow Setpoint (GPM)

1952:Flow Feedback (GPM) 1949:Flow Local Setpoint (GPM)

1952:Flow Feedback (GPM)

Setup Wizard::Application menu

1940: Pump Speed Max (RPM)

1941:Pump Speed Min (RPM)

1942:Pump Disp per Rev (in3)

1943:Flow FB Input Max (GPM)

1944:Flow FB Input Min (GPM)

1945:Flow SP Input Max (GPM)

1946:Flow SP Input Min (GPM)

1947:Flow Setpoint Max (GPM)

1948:Flow Setpoint Min (GPM)

1937:Disable Coast Stop

1960:Power Up Start

Quick Setup menu

1947:Flow Setpoint Max (GPM)

1948:Flow Setpoint Min (GPM)

1940:Pump Speed Max (RPM)

1941:Pump Speed Min (RPM)

0486:Acceleration Time (s)

0487:Deceleration Time (s)

1928:PID Proportional Gain

1929:PID Integral TC (s)

1934:PID Output Scaling

1932:PID Output Pos Limit (%)

1933:PID Output Neg Limit (%)

1006:Run Setup?

1141:View Level

www.comoso.com

6 Pump Control (US units) Application Manual

AC30V series Variable Speed Drive

Quick Monitor menu

1956:Auto Manual State

1997:Load Monitor State

1957:Feedback Input Break

1951:Flow Setpoint (GPM)

1952:Flow Feedback (GPM)

1954:Pump Demand (%)

1955:Actual Load (%)

1953:Flow Remote Setpoint (GPM)

1950:Flow Comms Setpoint (GPM)

1935:PID Output (%)

1936:PID Error (%)

1998:Expected Load (%)

1999:Load Error (%)

Setup::Application

Application

Pump and Flow

Sequencing

PID

Abnormal Load Detect

App Selection

Monitor::Application

Application

Pump and Flow

Sequencing

PID

Abnormal Load Detect

www.comoso.com

Pump Control (US units) Application Manual 7

AC30V series Variable Speed Drive

Pump and Flow

Setup::Application::Pump and Flow

Monitor::Application::Pump and Flow*

Application specific parameters to setup and monitor the pump and flow. All flow parameters are in Litres per minute (L/min).

PNO

Parameter Descriptions

1940Pump Speed Max

This is the maximum speed in RPM that the pump can operate. It is the same as the 0464:100% Speed in RPM parameter.

1941Pump Speed Min

This is the minimum speed in RPM that the pump is allowed to operate. It sets the low limit for the speed demand when running.

1942Pump Disp per Rev

This parameter sets the number of cubic inches (in3) displaced by one revolution of the pump. It is used to convert setpoints and

feedbacks given in US gallons per minute (GPM) to a pump speed in RPM.

1943Flow FB Input Max

This is the full range value in US Gallons / minute (GPM) in for the Flow Feedback analogue input (ANIN01). It corresponds to the

maximum input value of either 10V or 20mA depending on the setting of 0001: Anin 01 Type.

1944Flow FB Input Min

This is the minimum value in US Gallons / minute (GPM) for the Flow Feedback analogue input (ANIN01). It corresponds to the

minimum input value of either 0V, 0mA or 4mA depending on the setting of 0001: Anin 01 Type.

1945Flow SP Input Max

This is the full range value in US Gallons / minute (GPM) for the Flow Setpoint analogue input (ANIN02). It corresponds to the

maximum input value of 10V.

1946Flow SP Input Min

This is the minimum value in US Gallons / minute (GPM) for the Flow Setpoint analogue input (ANIN02). It corresponds to the

minimum input value of 0V.

1947Flow Setpoint Max

This is the maximum Flow Setpoint that can be set using the GKP, terminals or fieldbus.

1948 Flow Setpoint Min

This is the minimum Flow Setpoint that can be set using the GKP, terminals or fieldbus.

1949 Flow Local Setpoint

This is the Local Setpoint in US Gallons / minute (GPM) settable using the GKP. It is limited to be between 1947: Flow Setpoint Max

and 1948: Flow Setpoint Min, converted to a percentage of the flow rate at 0140: Pump Speed Max and then used to set the 0592:

www.comoso.com

8 Pump Control (US units) Application Manual

AC30V series Variable Speed Drive

PNO

Parameter Descriptions

Local Reference parameter.

1950 Flow Comms Setpoint*

This is the value of the remote terminal flow setpoint. It is clamped to be between 1947:Flow Setpoint Max and 1948:Flow Setpoint

Min

1951 Flow Setpoint*

This diagnostic is the value of the active flow setpoint. This will be the same as one of the following:

1953:Flow Remote Setpoint when in remote (terminal) control mode

1950:Flow Comms Setpoint when in comms control mode

1949: Flow Local Setpoint when in local control mode

1952 Flow Feedback*

This diagnostic is the value of the flow feedback in L/min. It is ANIN1 scaled and offset by 1943: Flow FB Input Max and 1944: Flow FB

Input Min.

1953 Flow Remote Setpoint*

This diagnostic is the value of the remote terminal flow setpoint. It is ANIN2 scaled and offset by 1945: Flow SP Input Max and 1946:

Flow SP Input Min, then clamped to be between 1947: Flow Setpoint Max and 1948:Flow Setpoint Min.

1954 Pump Demand*

This diagnostic is the requested speed of the pump as a percentage of 1940: Pump Speed Max. It is the same as 0500: Ramp Speed

Output.

1955 Actual load*

This diagnostic is the estimated load as a percentage of the maximum load. It is the same as the 0399: Actual Torque parameter

which is the calculated torque based on the IQ current.

Functional Description

The maximum pump speed is set in RPM using the 1940: Pump Speed Max parameter. This corresponds to 100% speed demand. A minimum

speed may be set using the 1940: Pump Speed Min parameter, also in RPM.

The calculation from flow the pump speed is set by the 1942:Pump Disp per Rev parameter.

The analog input used for the flow setpoint is scaled using the 1945: Flow SP Input Max and 1946: Flow SP Input Min parameters. These define

the range and offset in L/min. Similarly, the analog input used for the flow feedback is scaled using the 1947: Flow FB Input Max and 1948: Flow

FB Input Min parameters.

If not in flow control, the setpoint from either the GKP (1949: Flow Local Setpoint) or the communications (1950: Flow Comms Setpoint) may be

used instead of the setpoint from the terminals.

www.comoso.com

Altri manuali per AC30V Series

Indice

Altri manuali Parker Controllori

Parker

Parker HTR Series Manuale utente

Parker

Parker PSSV32A Istruzioni di installazione e manutenzione

Parker

Parker 514C Manuale utente

Parker

Parker 6K Series Manuale

Parker

Parker Sporlan S3C Manuale utente

Parker

Parker CM2115 Manuale utente

Parker

Parker IQAN-MC31 Manuale utente

Parker

Parker CHELSEA Manuale utente

Parker

Parker Compax3 Series Manuale utente

Parker

Parker AC30 series Manuale utente

Parker

Parker 6K8 Manuale utente

Parker

Parker PAC120 Series Manuale utente

Parker

Parker AC890PX Series Manuale utente

Parker

Parker ELL-1 Manuale utente

Parker

Parker 890 Series Manuale di istruzioni

Parker

Parker Sporlan Kelvin II Manuale utente

Parker

Parker Porter MPC Series Istruzioni per il montaggio

Parker

Parker HBN15 Scheda tecnica

Parker

Parker Compumotor 6000 Series Manuale utente

Parker

Parker LevelController SCLSD Manuale utente

Parker

Parker PAC340 Manuale utente

Parker

Parker Lucifer EPP4 P4BG4 Series Istruzioni utente

Parker

Parker ac890 Manuale utente

Parker

Parker PAC Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente