Parking Facilities PF6000 Manuale utente

Automatic Barrier Operation and

Maintenance Manual

Revision 10.5 2019

THIS DOCUMENT CONTAINS IMPORTANT

INFORMATION. IT MUST BE KEPT WITH THE

BARRIER AT ALL TIMES.

Address:

Tel:

Email:

Web:

Safety Features

Thank you for purchasing one of our perimeter security products.

Your barrier will provide safe and reliable service and peace of mind provided that the following

instructions and guidance is followed.

Your barrier is fitted with a range of safety devices designed to prevent accidents or injury, none the

less the area in the immediate vicinity of the barrier should be treated as potentially hazardous and

avoided whenever the barrier is moving (shown below).

Explanation of safety features and barrier reaction:

Dual Height Photocells –(either side of moving barrier leaf) stops barrier closing and

reverses to the fully open position. (IF FITTED)

CAT 3 Safety Edges –Safety edges are direction dependant and will stop barrier and reverse

in the opposite direction to which the barrier was moving. (FITTED ON PLAIN POLE ARMS)

Emergency Stop Button –located on the front of the barrier cabinet this can be used before

an incident happens (IF FITTED)

Please Note:

Inductive safety edges are fitted as standard to meet the force limitation as required and

specified in BS EN12978:2000, unfortunately this cannot be achieved when under lattice or

security hi-bar lattice is installed / retro-fitted to the barrier beam. It is the responsibility of

the installer to carry out the necessary risk assessment and install the appropriate safety

devices to make the barrier meet the current standards such as light curtains, laser safety

sensors or photo electric cells.

Safe use warnings:

1. Do not allow children/people with physical or mental impairment to play on or near the

barrier. Barriers are designed for vehicular use only

2. Keep remote control devices away from children.

3. Do not try to pass through/over/under the moving barrier.

4. Do not stop unnecessarily when passing through the barrier.

5. Only operate the barrier controls when in view of the barrier.

6. Do not attempt to interfere or modify the barrier from the factory setup.

7. Make sure the barrier is maintained by a trained and qualified powered barrier specialist at

the prescribed 6 monthly intervals and that services are recorded in this manual’slog.

8. If any sign of malfunction occurs switch off the barrier, manually release it and contact a

trained and qualified powered barrier specialist immediately.

Address:

Tel:

Email:

Web:

Safe Use Instructions

To open the barrier:

The barrier may be opened using the Open push button input, panel mounted keypad button, exit

loop or radio fob (if fitted). The barrier will smoothly accelerate to fast speed until the intermediate

limit is reached, at which point the barrier will smoothly decelerate for the remainder of the travel

distance. The barrier may be closed using the Auto-Close function, the Close button input, panel

mounted keypad button or radio fob. The barrier will smoothly accelerate to full speed until the

intermediate limit is reached, at which point the barrier will decelerate for the remainder of the

travel distance.

If a safety device is activated (i.e. safety edge or photocell) during the closing cycle the barrier will

stop & return to the fully open position. The barrier may only be closed once the obstruction has

been removed.

To close the barrier:

If a safety device is activated (i.e. safety edge or photocell) during the closing cycle the barrier will

stop & return to the fully open position. The barrier may only be closed once the obstruction has

been removed.

The barrier can also be closed by external devices but also using the down arrow on the front of the

control panel.

Address:

Tel:

Email:

Web:

Manual operation: WARNING SWITCH POWER OFF FIRST!

In the event of a power cut or other fault it will be necessary to move your barrier in manual mode.

Manual operation should only be attempted by a responsible adult. Before doing this always switch

the system off at the main isolator, your installer will have shown you where this is on yoursystem.

One the HD barrier due to the different mounting you have a cover plate that has thumb

screw Allen key bolts that need removing and then this allows access to the manual release.

This is located on the side panel of the barrier. Please note! On removal of the correct screw

this will activate a safety switch which will stop the barrier moving automatically. THE

POWER MUST ALSO BE TURNED OFF at the isolator as a failsafe BEFORE! this isattempted.

Fig 1 HD Model Fig 2

You can now move the barrier manually. Only move the barrier very slowly, no faster than it moves

in normal use. Your installer will have demonstrated this at handover.

To return the barrier to automatic operation (when the power is restored) simply follow the steps

above in reverse order: Fig 3 Shown below where the manual release is underneath the barrier lid.

Fig 3 Lux/S/B Model

Address:

Tel:

Email:

Web:

General:

End User Regular Safety Checks

Keep the areas around the barrier clear of obstructions at all times, cut back plants and weeds that

might interfere with the barrier safety devices and its safety sensors. Keep the photo electric beam

covers clean. Make sure pedestrian routes which are Cleary marked are always accessible.

Safety checks:

These user safety checks should be conducted every [few weeks] by a responsible adult who has

been shown how to do the checks by a trained and qualified powered barrier specialist. We will

demonstrate the user checks to you as part of the handover process.

[Insert instructions]

Address:

Tel:

Email:

Web:

Engineer Planned Preventative Maintenance Schedule

Your barrier will need to receive regular planned preventative maintenance in order to remain in

safe and reliable service. The maintenance outlined below should only be conducted by a trained

and qualified powered barrier specialist who is familiar with 6000 automation equipment and has

the necessary test equipment. [insert company] can provide this service and you will have been

offered a maintenance contract as part of the supply process. If the maintenance outlined below is

not completed, [insert company] cannot accept responsibility for injuries, accidents or breakdowns

caused by lack of maintenance.

You are reminded that, as the person in control of the barrier, you have a legal duty of care to users

and to visitors to the premises (including trespassers). If the barrier is not kept safe, any party whose

property is damaged or who is injured by the barrier is likely to be able to sue for damages.

If the barrier is part of an undertaking (such as at rented property), the person in control of it will have

additional duties under section 3 of the Health and Safety at Work Act 1974 to keep the barrier

maintained in a safe condition.

If the premises are also a workplace, there are specific duties under regulation 5 and 18 of the

Workplace (Health and Safety and Welfare) Regulations 1992.

Failure to meet duties imposed by health and safety legislation can result in criminal proceedings.

A maintenance log is provided at the end of this book to record completed maintenance. Please

make sure the maintenance log is completed and signed on completion of any maintenance work.

At 6 month intervals:

Inspections:

Check that all gearbox and motor mountings are tight and secure

Check that the barrier manual release is still functioning

Check that the barrier is stable and moves freely when the manual release is engaged and power is

switched off!

Check flashing beacon is working (if fitted)

Check that the emergency door switch button works

Check that the manual release emergency switch button works (HD Model)

Check all safety edges work and are working for the correct direction of travel

Check the photocells are working and in the correct direction of travel

Check that no one has made the barrier unsafe by speeding it up past the factory settings

Check that the control program has not been modified such as to make the barrier unsafe. Please

consult the manufacturer if in doubt. Call the manufacturer to talk this through if in doubt, use

common sense and it is better to check everything twice!

Address:

Tel:

Email:

Web:

Lubrication:

Any grease nipple (All other items are “sealed for life” and require no lubrication)

Function checks:

•Overall barrier structure is plumb

•Lubricate any parts that need lubricating see section “Lubrication” above

•Gearbox oil level

•Function of manual release

•Torque setting on control unit (If obstacle detection has been used)

•Obstacle detection effectiveness (measure forces: not a legal requirement)

•Overall function/condition of motor/gearbox

•Function and condition of safe edges

•Photocells internal and external

•Sealing of photocell covers and cable entry

•Wire terminations in control panel

•Sealing of control unit cover and cable entries

•Condition of all wiring and junction boxes

•Function of all controls –transmitters, loop and intercoms

•Security and effectiveness of all earth connections

•Test earth fault loop resistance and RCD function (MCB is preferred)

•Reassess and check the ongoing validity of the hazard assessment

Performance tests:

Force Test (Not a legal requirement but advisory)

Check that the manual release is working

Ensure that the barrier is running smoothly

Check Flashing Beacon is working (If fitted)

Check any safety devices fitted are working as designed (Loops/Photocells/Light Curtains etc.)

Address:

Tel:

Email:

Web:

Handover Check list

The following items have been explained to the client: [tick] ✓

□How to operate the barrier.

□How to isolate the power to the barrier.

□How to manually release the barrier.

□How the safety features of the barrier work.

□How to avoid any residual hazards associated with the barrier.

□How to use the activation devices.

□How to change the batteries on remotes etc.

□How to change the keypad pin code.

□How and when to perform the required safety checks.

□Other [insert]

The following items have been passed to the client.

□Manual release instructions.

□Intercom user manual.

□Declaration of Conformity.

□User warnings and residual hazard identification.

□Planned Preventative Maintenance instructions.

□Maintenance log.

□Other [insert]

Installer Name: Date:

Signature:

Client Name: Date:

Signature:

Address:

Tel:

Email:

Web:

Component list

Drive unit:

Control panel: Feig TST FUZ PFL2 B

Limit Switches: Schneider XCKN2118P20 Limit Switch

Door/Manual Release Safety Switch: Schneider XCMN21FOL2 Safety Door Switch

Loop Detector: Feig SUVEK1A (Single) SUVEK2A (Dual)

Pole Arm Adaptors: HD-PAA / STD-PAA

Address:

Tel:

Email:

Web:

Maintenance log

Date

Work done

Company

PPM

Name

Reactive

Signature

Date

Work done

Company

PPM

Name

Reactive

Signature

Date

Work done

Company

PPM

Name

Reactive

Signature

Date

Work done

Company

PPM

Name

Reactive

Signature

Date

Work done

Company

PPM

Name

Reactive

Signature

Date

Work done

Company

PPM

Name

Reactive

Signature

Date

Work done

Company

PPM

Name

Reactive

Signature

Altri manuali per PF6000

Indice

Altri manuali Parking Facilities Barriera automatica

Parking Facilities

Parking Facilities PF6000X Manuale di istruzioni

Manuali Barriera automatica popolari di altre marche

Cardin

Cardin EL Series Manuale utente

BFT

BFT Maxima Ultra 36 Manuale utente

Lip

Lip SLEEK TIME Manuale utente

AMC

AMC FLEX 500 - 2000 Manuale del sistema

CAME

CAME GARD series Manuale utente

FAAC

FAAC B680H Manuale utente

Proteco

Proteco S-Park Series Manuale utente

Politec

Politec MANA DT SMA Manuale

King gates

King gates Open 424 Manuale utente

RIB

RIB RAPID S P1-CRX Manuale utente

Erreka

Erreka ULTRA Series Istruzioni operative

BFT

BFT MOOVI 30 Manuale utente

FAAC

FAAC B 604 Manuale utente

Alvarado

Alvarado SUPERVISOR 4500 Manuale utente

PPA

PPA BARRIER BRC Manuale utente

Maxon

Maxon GPC X1-LD Manuale utente

quiko

quiko QK-CT273800LK4 Manuale elenco delle parti

Watt Plastics

Watt Plastics PVC Picket Fence Manuale utente