Parkside PDAP 75 A1 Manuale utente
AIR POLISHING SET PDAP 75 A1
AIR POLISHING SET
Translation of the original instructions
IAN 315468
DRUCKLUFT-POLIERSET
Originalbetriebsanleitung
PERSLUCHT-POLIJSTSET
Vertaling van de originele gebruiksaanwijzing
POLISSEUSE PNEUMATIQUE
Traduction des instructions d’origine
GB/IE/NI Translation of the original instructions Page 1
FR/BE Traduction des instructions d’origine Page 25
NL/BE Vertaling van de originele gebruiksaanwijzing Pagina 51
DE/AT/CH Originalbetriebsanleitung Seite 77
Before reading, unfold the page containing the illustrations and familiarise
yourself with all functions of the device.
Avant de lire le mode d’emploi, ouvrez la page contenant les illustrations et
familiarisez-vous ensuite avec toutes les fonctions de l’appareil.
Vouw vóór het lezen de pagina met de afbeeldingen open en maak u
vertrouwd met alle functies van het apparaat.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen
Sie sich anschließend mit allen Funktionen des Gerätes vertraut.
PDAP 75 A1 GB│IE│NI │ 1 ■
Contents
Introduction...................................3
Intended use..........................................3
Features .............................................4
Included in delivery ....................................4
Technical data ........................................4
General safety instructions for compressed air tools .6
Hazards caused by flying parts ...........................7
Hazards caused by entanglement .........................7
Hazards during operation ...............................7
Risks due to repetitive movements. . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hazards caused by accessories...........................9
Hazards in the workplace ...............................9
Hazards caused by dust and vapours .....................10
Risks due to noise.....................................11
Risks due to vibrations .................................12
Additional safety instructions for pneumatic machines.........12
Appliance-specific safety instructions for grinders ............13
Before use ...................................13
Assembly/disassembly of the polishing disc ................13
Fitting the polishing attachments..........................14
Lubrication ..........................................15
Topping up the oil ....................................15
Connecting to a compressed air source....................16
PDAP 75 A1
■ 2 │ GB│IE│NI
Operation ...................................16
Switching on and off ..................................16
Polishing ............................................16
Maintenance and cleaning......................18
Troubleshooting ..............................19
Disposal.....................................20
Kompernass Handels GmbH warranty ...........21
Service ......................................23
Importer ....................................23
Translation of the original Conformity Declaration ..24
PDAP 75 A1 GB│IE│NI │ 3 ■
AIR POLISHING SET PDAP 75 A1
Introduction
Congratulations on the purchase of your new appliance. You have
chosen a high-quality product. The operating instructions are part of
this product. They contain important information about safety, usage
and disposal. Before using the product, please familiarise yourself
with all operating and safety instructions. Use the product only as
described and for the range of applications specified. Please also
pass these operating instructions on to any future owner.
Intended use
This compressed air polisher is designed for polishing various surfac-
es. Any other usage or modification of the appliance is deemed to
be improper and carries a significant risk of accidents.
The manufacturer accepts no responsibility for damage(s) resulting
from improper usage. This appliance is intended for domestic use only.
Symbols on the compressed air tool:
WARNING! Read the operating instructions before use.
Always wear eye protection when using or maintain-
ing the compressed air polisher.
Always wear a dust mask in situations in which dust
is being generated.
Always wear hearing protection.
Oil daily
PDAP 75 A1
■ 4 │ GB│IE│NI
Features
Air inlet
Connector nipple (preassembled)
Trigger
Thread
Polishing disc
Polishing hood black
Polishing hood orange
Fake fur attachment
Assembly spanner
Included in delivery
1 air polishing set PDAP 75 A1
1 polishing disc Ø 75 mm (with Velcro fastener)
1 polishing hood, orange (for pre-polishing)
1 polishing hood, black (for final polishing)
1 fake lambskin
1 connector nipple 6.35 mm (1/4”) (preassembled)
1 assembly wrench
1 operating manual
Technical data
Rated frequency: max. 2500 rpm
Rated air pressure: max. 6.3 bar
Grinding disc: Ø 75mm
Weight (without accessories): approx. 740 g
PDAP 75 A1 GB│IE│NI │ 5 ■
Noise emission values:
Noise measurement determined in accordance with ISO15744:
Sound pressure level: LpA = 84.1 dB(A)
Uncertainty: KpA = 3 dB
Sound power level: LWA = 95.1 dB(A)
Uncertainty: KWA = 3 dB
Wear ear protection!
Vibration emission value:
Vibration values determined in accordance with ISO 28927-3 and
EN 12096:
ah= 0.25 m/s2
Uncertainty K = 0.52 m/s2
WARNING!
► The noise emission levels specified in these instructions have
been measured in accordance with the standardised measur-
ing procedure specified in ISO 15744 and can be used to
make equipment comparisons. The noise emission values vary
in accordance with the use of the compressed air tool and may
be higher than the values specified in these instructions in some
cases. It is easy to underestimate the noise emission load if the
compressed air tool is used regularly in a certain manner.
NOTE
► For an accurate estimate of the noise emission load during a
certain working period, the times during which the appliance is
switched off or is running but not actually being used must also
be taken into consideration. This can significantly reduce the
noise emission load over the total working period.
PDAP 75 A1
■ 6 │ GB│IE│NI
WARNING! General safety instructions for
compressed air tools
WARNING!
► For multiple hazards: Please ensure that you have read and
understood the safety instructions before adjusting, operating,
repairing, maintaining or replacement of accessories on the
polisher as well as before working in the vicinity of the ma-
chine. Failure to do this can result in serious bodily injury.
■ The sander or the polisher should only be adjusted, set or used
by adequately qualified and trained operators.
■ This sander or this polisher may not be modified. Modifications
can reduce the effectiveness of the safety measures and increase
the risks for the operator.
■ The safety instructions should not be lost – give them to the oper-
ator.
■ Never use damaged sanders or polishers.
■ The appliance must be inspected regularly to ensure that it is
labelled with the required rated values and markings given in
this manual. The user must contact the manufacturer to obtain
replacement labels if necessary.
PDAP 75 A1 GB│IE│NI │ 7 ■
Hazards caused by flying parts
■ If a workpiece or accessory or even part of the machine tool itself
breaks, parts can be flung out at high speeds.
■ When operating the sander or the polisher or when exchanging
accessories on the appliance, always wear eye protection. The
degree of necessary protection must be evaluated separately for
each individual task.
■ Wear a safety helmet if working above head height. In this case,
the risks for others should also be assessed.
■ You must ensure that the workpiece has been securely fixed.
Hazards caused by entanglement
■ Suffocation, scalping and/or cut wounds can occur if loose cloth-
ing, jewellery, necklaces, hair or gloves are not kept away from
the machine and its accessories.
Hazards during operation
■ When using the machine, the operator’s hands can be subject to
hazards such as cuts, grazing and heat. Wear suitable gloves to
protect your hands.
■ The operator and maintenance personnel must be physically
capable of handling the size, mass and power of the machine.
■ Hold the machine correctly: be ready to counteract any normal
or sudden movements - have both hands ready.
■ Ensure that your body is balanced and that you have a secure
standing position.
■ Release the start/stop control in case of a disruption to the elec-
tricity supply.
■ Use only the lubricants recommended by the manufacturer.
Altri manuali per PDAP 75 A1
4
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Parkside Levigatrice
Parkside
Parkside PDS 290 A1 Manuale utente
Parkside
Parkside PHS 160 B2 Manuale utente
Parkside
Parkside PBTS 370 A1 Guida rapida
Parkside
Parkside PEXS 270 A1 Manuale utente
Parkside
Parkside PDAP 75 A1 Manuale utente
Parkside
Parkside PHS 160 B2 Manuale utente
Parkside
Parkside 390384 2201 Manuale utente
Parkside
Parkside KH 3028 RANDOM ORBITAL SANDER Manuale utente
Parkside
Parkside PHS 160 E5 Manuale utente
Parkside
Parkside KH 3115 BELT SANDER Manuale utente
Parkside
Parkside PBS 600 A1 Manuale utente
Parkside
Parkside PDS 290 A1 Manuale utente
Parkside
Parkside PWP 90 A1 POLISHING MACHINE Manuale utente
Parkside
Parkside PBS 600 A1 Manuale utente
Parkside
Parkside PMFS 200 C3 Manuale utente
Parkside
Parkside PDS 290 B2 Manuale utente
Parkside
Parkside PSS 250 Manuale utente
Parkside
Parkside PMFS 200 B2 Manuale utente
Parkside
Parkside PDS 290 B2 Manuale utente
Parkside
Parkside PEBS 900 SE Guida rapida
