Patton electronics 1195/8E1 Manuale utente
Optical Multiplexer
Quick Start Guide
Part Number: 07M1195-QS, Rev. A
Revised: February 12, 2009
SalesOffice:+1(301)975-1000
Technical Support: +1 (301) 975-1007
E-mail:[email protected]
WWW:www.patton.com
Model 1195/8E1
2
Model1195/8E1QuickStartGuide
• This device contains no user serviceable parts. The equipment shall be
returned to Patton Electronics for repairs, or repaired by qualified
service personnel.
• Mains Voltage: Line voltages are present when the power cord is con-
nected. The mains outlet shall be within 10 feet (3 meters) of the
device, shall be easily accessible, and protected by a circuit breaker.
• For AC powered units, ensure that the power cable used meets all
applicable standards for the country in which it is to be installed, and
that it is connected to a wall outlet which has earth ground.
• Hazardous network voltages are present in WAN ports, regardless of
whether power to the unit is ON or OFF. To avoid electric shock, use
caution when near WAN ports. When detaching the cables, detach the
end away from the unit first.
• Do not work on the system or connect or disconnect cables during
periods of lightning activity.
• For units with an external power adapter, the adapter shall be a
listed Limited Power Source.
WARNING
Model1195/8E1QuickStartGuide
3
1.0 Connecting power
AC Mains version:
PleaseusetheACmaincable(provided)toconnectthesystemtoyourACmainspower
outlet.
DC Mains version
:PleaseconnecttheDCmainscable(provided)tothesystem.Thepolarityshouldnotbe
reversedwhileconnecting.Otherwise, you can get your system damaged.
1.1 AC Power
ToconnecttheAC220Vpower:
1.2 DC Power
ToconnecttheDC-48V:
DC 48 V
E1 4-1
II
~ 220 V
PGND GND -48V
OPTICAL B
TX RX
OPTICAL A
TX RX
RS232
CONSOLE
DC Power
Cable
E1 8-5
II
From AC Source
(220V)
DC 48 V
E1 4-1
II
~ 220 V
PGND GND -48V
OPTICAL B
TX RX
OPTICAL A
TX RX
RS232
CONSOLE
IEC 60320
Female
IEC 60320
Male on Unit
E1 8-5
II
4
Model1195/8E1QuickStartGuide
1.3 Grounding
WhentheequipmentisusedwiththeAC~220Vpowersupply,the3-coresocketmustbegroundedforprotec-
tion.Theotherequipment,e.g.opticalterminal,connectedwiththisequipmentmustalsobegrounded
ToconnecttheEarth:
2.0 Connecting the optical interface
Note
Donotexposetothenakedeye.ConnectfibercabletosystemwhenpowerisOFF.
Note
ForTesting:
ALWAYS INSTALL OPTICAL ATTENUATORS. For distances of less than 10 km, optical attenuators
must be installed on the Optical Links. Otherwise, the optics will be permanently damaged.
Model1195/8E1QuickStartGuide
5
3.0 Connecting the DB-37 connector
DC 48 V
E1 4-1
II
~ 220 V
PGND GND -48V
OPTICAL B
TX RX
OPTICAL A
TX RX
RS232
CONSOLE
DB-37 (Female)
Connector
118
19 37
RJ-45 (F)
Connector
1
RJ-45 (F)
Connector
2
RJ-45 (F)
Connector
3
RJ-45 (F)
Connector
4
E1 8-5
II
4xE1 Signals
6
Model1195/8E1QuickStartGuide
4.0 Connecting E1 Links
ConnectE1 lineafterensuring thattransmissiondevice havebeengrounded. ABitError Rate(BER)testmay be
conductedonE1LinkusingaBERTtestertoensurethattheE1errorsarewithinthepermittedlimits/threshold.
4.1 Definition for E1 Interfaces
TheE1Interface(RJ-45connector)isdefinedas:
5.0 Connecting Ethernet Links
PleaseconfiguretheEthernetportoftheequipmentatbothsidesaswellastheEthernetPortsofthedevicesthat
areconnectedtotheequipment.ConnecttheEthernetlinks.
PleaseensurethattheconnectingLANsonbothsidesofthelinkareoperatinginthesameIPdomain.
5.1 Verifying the connection
PingovertheEthernetconnectionfromonesidetotheother(near-end to the far-end)toverifythelink.
5.2 Definition for Ethernet Interfaces
TheEthernetInterface(RJ-45connector)isdefinedas:
1 2 3 4 5 6 7 8
Tx+ Tx- Rx+ N/C N/C Rx- N/C N/C
Data Out + Data Out - Data In + Data In -
1 2 3 4 5 6 7 8
Rx+ Rx- N/C Tx+ Tx- N/C N/C N/C
Data In + Data In - Data Out + Data Out -
Model1195/8E1QuickStartGuide
7
6.0 Connecting the RS-232 port
Note
AnRS-232COMportcableisprovidedwiththe1195/8E1system.
6.1 RS-232 port cable details
End1
End2
Typeofcable Twistedpaircable-solidconductor
Numberofpairs 2
Diameter 24AWG
Length 3meters
Connections Asperdetailsgivenbelow
DB-9 (Female Connector)
DB-9 (Female Connector)
8
Model1195/8E1QuickStartGuide
6.2 RS-232 pin definition
DB-9 Pin Number Definition
RS-232
2 RS-232inputsignalformanagement
3 RS-232outputsignalformanagement
5 GND
OthersNC
Model1195/8E1QuickStartGuide
9
7.0 Configuring HyperTerminal
1.
ClickontheStartbuttonfromthetaskbaronyourPC.
2.
SelectPrograms>Accesories>Communications>HyperTerminal.Thefollowingscreenwilldisplay:
3.
EnteranameforthenewconnectionandclickOK.Theconnectionwindowwilldisplay:
4.
SelecttheCOMportfromthedrop-downmenu,andclickOK.Thepropertieswindowwilldisplay:
10
Model1195/8E1QuickStartGuide
5.
ChangetheBitspersecondoptionto19200andchangetheflowcontroloptiontoNone.
TheCOMPropertiessettingsshouldbe:
6.
ClickApply,thenclickOK.
7.
AnewHyperTerminalsessionscreenwilldisplay. Press Enter. The system prompt will appear on the
screen.Thispromptis generated by the system. Now,youmayaccess/configurethesystemwiththeCLI
commands.
Note
RemembertosavethesettingsforfutureusebeforeyouexittheHyperTerminalwindow.
Note
Fordetailedinformationaboutconfiguringthe1195/8E1systemusingCLIcommandsortheGraphi-
calUserInterface(GUI),refertothe
Model1195/8E1GettingStartedGuide
thatcamewithyourunit.
Bits per second
19200
Data bits
8
Parity
None
Stop bits
1
Flow control
None
Indice
Altri manuali Patton electronics Multiplexer
Patton electronics
Patton electronics 3028 Turbo Guida all'installazione
Patton electronics
Patton electronics 3022 Manuale utente
Patton electronics
Patton electronics 3042 Manuale utente
Patton electronics
Patton electronics MicroStat II 3022 Manuale utente
Patton electronics
Patton electronics 1195/4E1 Manuale utente
Patton electronics
Patton electronics 3046/V24 Manuale utente
Patton electronics
Patton electronics 3054 Manuale utente
Patton electronics
Patton electronics 3054 Manuale utente
Patton electronics
Patton electronics Multiport Asynchronous Statistical Multiplexer... Manuale utente
