PawTrax Micro Manuale utente
PawTrax GPS Pet Tracker
user manual – updated 1/8/2014
Introduction
The PawTrax Micro is a small and powerful tracking device. On request it will send its location to the
user’s mobile phone or our mapping platform at www.gpstrackingmap.com. The device has been
designed in such a way that it can be used for other applications such as KidTrax, PeopleTrax. It can
be attached to a key ring or lanyard or covertly hidden in an asset. Also see our PeopleTrax Plus on
our website
Main Features – some are more applicable to certain applications
Locate and Track via SMS and GPRS
Listen in function
SOS alert button
Geo-fence alarm
Speeding alert
Low battery alert
Specification
Dimension 58.2mm x 23.0mm x 11.2mm
Weight 23g
Network GSM/GPRS
Band 850/900/1800/1900Mhz
GPS chip SIRF3 chip
GPS sensitivity -159dBm
GPS accuracy 5m
Cold start 42 sec.
Warm starts 38 sec.
Hot start 1 sec.
Operation temperature -20°C to +55°C
Humidity 5%--95% non-condensing
Please note all of the below settings can be configured using the PawTrax app available from the
Android and IPhone stores – this eliminates the need to remember and configure sms messages
(recommended).
Getting Started
Charge the battery for 8 -12 hours for the first three times. After the first three times, the battery can
be charged fully in 3-5 hours. In order to protect the device please use the battery and charger
provided. Connect to PawTrax before connecting and switching on mains.
SIM CARD – standard size: Please be sure that there is call display but no call transfer, and PIN
code is off
Switch on: Take the unit outdoors or place near a window. The device will be switched on after
inserting the SIM card. To switch off: Take out the SIM card. Use the supplied plastic tool to insert
sim.
1. SOS Button
2. LED
3. Microphone
4. SIM card Slot
5. USB Connector
LED Status
Yellow flashing every 0.1 seconds – Blue constant Start up sequence
Yellow flashing every 3 seconds Connected to GSM
Yellow double flashing every 3 seconds Connected to GPRS
Blue flashing every 3 seconds GPS fix
Red (next to charging socket) On – charging
Off – charged
Red on front Battery low
Set the authorised number.
Send SMS“123456A1,phone number” to set the first number. At least 1 authorised number must be
set.
Command SMS
Password
A1/2/3/4/5
Authorised number
Reply SMS
Send SMS “123456A1,phone number” to set the first number.
This number will also receive low battery warning SMS
Send SMS “123456A2,phone number” to set the second number.
Send SMS “123456A3,phone number” to set the third number.
Send SMS “123456A4,phone number” to set the fourth number.
Send SMS “123456A5,phone number” to set the fifth number.
All numbers will receive the location message when requested
Note: 123456 is the default password. ‘A’ must be in upper case and make sure there is no space in
the command. Phone number must include the country code
E.g. send SMS “123456A1,+4413812345678” to set +4413812345678 as the first SOS number. +44
is the country code of UK. Please do not use 00 instead of +.
The device will only accept SMS commands from the authorised numbers.
Delete authorised number.
Send SMS“123456A1,D” to delete the first number.
Send SMS“123456A2,D” to delete the second number.
Send SMS“123456A3,D” to delete the third number.
Send SMS“123456A4,D” to delete the fourth number.
Send SMS“123456A5,D” to delete the fifth number.
E.g. send “123456A1,D” to delete the first number
Modify the password
Send SMS “123456H******” to change the password.
Note: ****** is the New password. H must be upper case, send it to tracker to modify the
password. (Default password: 123456)
E.g. send “123456H456789” means change the password 123456 to 456789 The password won’t
be erased by changing SIM card.
Be sure to keep the password safe, otherwise it will have to be returned for resetting. The
password must be 6 numbers, If not the tracker cannot recognize the password.
Get position by sms
Send SMS “123456F” to the device and it will reply its position by SMS. Only the authorised
number can get the reply. Note: F must be in uppercase.
E.g. send “123456F” to the unit. It will reply its position.
Command SMS
Password
Command
Reply SMS
Continuous tracking function
Send SMS “123456M0/M1,xxxS/M/H” to the unit, the tracker will send the location message
according to the time intervall as an sms to authorised number A5.
M0 means turn off, M1 means turn on
xxx means time interval and must be three numbers,030S means 30S. S means second, M means
minute, H means hour
H should be≤90, S,M should be <255
E.g. send“123456M1,030S” to the tracker means every 30 seconds send back a position coordinate
to the A5 number. Send“123456M0,030S” to the tracker means stop the continuous tracking.
This function is also used to set the update time to the mapping platform if used. In this case it will
report via GPRS to the platform and not to the mobile numbers.
Command SMS
Reply SMS
Tracking data
SOS function (not applicable to pet tracking)
Press and hold the SOS button for approx 3 seconds and it will send SOS Alert to A1, A2, A3
authorised numbers. In addition the device will call authorised numbers in turn, open up the
microphone, allowing the authorised number to listen in to the sound around the tracker.
SOS function can also be set up via the GPRS web platform enabling alerts to be sent via email.
Listen in function (not applicable to pet tracking)
If an authorised number calls the tracker and waits for the tracker to pick up the call you can hear
the sounds around the tracker (voicemail must be off)
Speeding alert
Send SMS “123456J0/J1,speed” to set the Speeding alert function. Note: J must be uppercase
J0 means turn off the over speed alert function; J1 means turn on the speeding alert function. Speed
should be <250 and must 3 numbers, e.g. 080= 80 km/h.
For example, send “123456J1,080” to tracker. When the object exceeds 80 km/h, the unit will send
SMS as “Over speed! +GPS info” to the A1, A2 ,A3 number. Send “123456J0,080” to tracker means
turn off the speeding alert function.
Command SMS
Reply SMS
GEO-Fence
Send SMS “123456Ixyz,aabbccddefffgghhiijkkllmmnneppp qqrrssj” to set up the geo-fence for the
device to restrict its movement within an area. The device will send the message to the A1, A2, A3
numbers as “Stockade +geo info” when it breaches the district.
There are 5 GEO-FENCES can be set for the tracker.
Note: It must be English in capital. x=NO. of the GENFENCE(1-5)
y=1 means turn on, y=0 means turn off z=0 means go into, z=1 means go out of
Altri manuali PawTrax GPS
