Paxton ins-40213-US Manuale utente
Paxton
ins-40213-US
Paxlock US
1
x 2 x 2
X 3
1
2*
3
4
5
6
8
910
15
16
17 18
19*
7
20 21
22
11
12
13
14
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
Tools List
What’s in the box
1) Front handle
2) Lock Cylinder *
3) Paxlock front housing
4) Motor adjustment plate
5) Motor
6) 2-3/8” Latch
7) Latch screws x 2
8) Motor backplate
9) Backplate/Rose assembly
10) Paxlock rear housing
11) 4 x AA Alkaline batteries
12) Rear battery cover
13) Rear handle cover
14) Rear Handle
15) Small mounting screws x 2
16) Long mounting screws x 3
17) Battery cover key
18) Handle removal pin
19) Keys x 2 *
20) Handle washers x 2
21) Strike plate
22) Strike plate screws x 2
Knife
Adhesive tape
Pencil
Tape measure
* Not for SFIC
Power Drill
Drill bits (1”, 5/16”, 5/8”, 1/8”)
Crosshead screwdriver
Chisel 1”
2
1
2
2-3/8” (60mm) backset
5/16” (8mm)
5/16” (8mm)
5/16” (8mm) 5/16” (8mm)
2-1/8” (54mm)
5/16” (8mm)
5/8” (16mm)
3
1” (25mm) Width
3-1/4” (82mm) Depth
x 2 x 2
X 3
1
2*
3
4
5
6
8
910
15
16
17 18
19*
7
20 21
22
11
12
13
14
Step 1: Marking out
Tape template to door, mark holes then remove
template for drilling.
Step 2: Drilling
To ensure accuracy you should drill holes from
both sides of the door towards the center. This
avoids the risk of damaging the door face when
the drill breaks through.
Make sure to include pilot holes either side of
the central hole to ensure ush tting of the
motor plates.
Step 3: Marking out and chiseling for latch
To install the latch; drill a 1”(25mm) hole, slide in
the latch, then draw around the faceplate.
Remove the latch and score the outline with
a knife to avoid splitting the wood when
chiselling.
3
4
6
5
Step 6: Inserting the motor
Pass the motor through the central hole within
the door, making sure to pass the motor lead
through the hole rst.
Step 5: Fitting the strike plate
Close the door to mark the horizontal line of the
strike plate.
Measure one half of door thickness from door
stop to mark vertical center line of the strike.
Drill 1” (25.4mm) hole, 1/2” (12.7mm) deep at
intersection of horizontal and vertical center
lines.
Cut out jamb 3/32” (2.4mm) deep or until the
strike is ush with jamb. Tighten the strike plate
screws securely.
Step 4: Fitting the door latch
Attach the latch using the screws provided.
4
8
9
7
- 1-3/4” (45mm)
- 2” (50mm)
Step 8: Ensuring the latch engages
Make sure the tail of the latch is engaging with
the motor retractor correctly as illustrated.
Step 7: Rotating the motor adjustment plate
To ensure that the motor adjustment plate is at
the correct distance, rotate until it sits ush with
the door and the motor has engaged properly.
Please refer to the diagram for the correct
position of the plate for each door thickness.
Step 9: Fitting the front housing
Line up front housing and ensure the body is
ush to the door.
*PaxLock US is set up for RH doors by default –
please see page 8 for LH operation.
5
13
14
15
10
11
12
Step 10: Fitting the rear backplate
assembly
Feed the motor cable through the
hole in the motor back plate.
Step 11: Fitting the rear housing and motor
wiring
Feed both the cables through the rear housing
cutout and t the lower long mounting screws.
Step 12: Fitting the rear lock assembly and
wiring
Fit top, long mounting screws and 2 lower short
screws.
6
13
14
15
10
11
12
Step 10: Fitting the batteries
Step 11: Securing the rear cover
Step 12: Fitting the cover plate and handle
7
Optional step: Contact switch Optional step: Inserting the handle washers
Handle feel can be tightened with the use of
the included washers.
Optional step: Handle orientation for LH door
To congure for LH door operation, remove the front and rear handles using the handle removal
pin. Unscrew the 4 screws securing the rose to the front/rear housings, rotate 180 degrees and
screw back together.
Ret the handles, and push home until the axle engagement clicks.
8
≤ 200
x1
x1
≤ 1000
Net2 Pro/Net2 Lite: http://paxton.info/1438
Software installation
0 m
3m
15m
20m
30m
50ft
65ft
100ft
10ft
0 ft
Wireless Signal Range
9
1
2
4
56
3
Enrolling a PaxLock
1
4
2
3
21
43
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Paxton Controllori di accesso IP
Paxton
Paxton Ins-30160 Manuale utente
Paxton
Paxton 690-333-US Manuale utente
Paxton
Paxton Net2 PaxLock Manuale utente
Paxton
Paxton Ins-30003 PROXIMITY P Series Manuale utente
Paxton
Paxton Proximity LCD reader Manuale utente
Paxton
Paxton Switch2 Manuale utente
Paxton
Paxton ins-20100 Manuale utente
Paxton
Paxton Easyprox nano Manuale utente
Paxton
Paxton TOUCHLOCK K Series Manuale utente
Paxton
Paxton TOUCHLOCK APN-1003 Guida alla risoluzione dei problemi
Paxton
Paxton ins-30093-EX Manuale utente
Paxton
Paxton 353467V2 Manuale utente
Paxton
Paxton Ins-30156 PROXIMITY P Series Manuale utente
Paxton
Paxton PROXIMITY P series Manuale utente
Paxton
Paxton Ins-30150-US Manuale utente
Paxton
Paxton PROXIMITY P38 Manuale utente
Paxton
Paxton 333-110 Manuale utente
Paxton
Paxton Ins-30130 Manuale utente
