PBI DCH-4000P Manuale utente

DCH-4000P Series

Professional Digital Decoder

User Manual

Table of contents

1. SAFETY............................................................................................................................................... 1

2. TECHNICAL INTRODUCTION............................................................................................................ 2

2.1 Features......................................................................................................................................... 2

2.2 Factory Options ............................................................................................................................. 2

3. INSTALLATION.................................................................................................................................... 3

3.1 Inspection and Test........................................................................................................................ 3

3.2 Functional Self Test ....................................................................................................................... 4

3.3 Mounting ........................................................................................................................................ 4

4. FRONT PANEL.................................................................................................................................... 4

4.1 Front Panel List.............................................................................................................................. 4

4.2 Indicator LEDs ............................................................................................................................... 4

4.3 Liquid Crystal Display .................................................................................................................... 5

4.4 Keypad........................................................................................................................................... 5

4.5 Common Interface ......................................................................................................................... 5

5. REAR PANEL ...................................................................................................................................... 6

5.1 Power Supply................................................................................................................................. 6

5.2 Output Connectors......................................................................................................................... 6

5.3 ASI Input Connector....................................................................................................................... 7

5.4 RS-232 Interface............................................................................................................................ 7

5.5 Ethernet Interface .......................................................................................................................... 7

5.6 TS/IP Interface (Factory Optional) ................................................................................................. 7

6. INSTALLATION.................................................................................................................................... 7

6.1 Main Menu ..................................................................................................................................... 7

6.2 System Menu................................................................................................................................. 8

6.2.1 Local Setup ............................................................................................................................. 8

6.2.2 Setting up the Trap IP Address ............................................................................................... 8

6.2.3 Editing the Unit Name............................................................................................................. 9

6.2.4 Checking the Properties ......................................................................................................... 9

6.2.5 Recover Factory Default Settings ........................................................................................... 9

6.2.6 Setting Machine Type ............................................................................................................. 9

7. Manual for DCH-4000P-30S /-30T/-30C/-30S2 .................................................................................. 9

7.1 Menu Structure for DCH-4000P-30S /-30T/-30C/-30S2................................................................ 9

7.2 Setting Inputs for DCH-4000P-30S /-30T/-30C/-30S2 .................................................................11

7.2.1 Checking Status of Inputs ......................................................................................................11

7.2.2 Setting the Tuner Parameters................................................................................................11

7.3 Setting Outputs for DCH-4000P-30S /-30T/-30C/-30S2.............................................................. 13

7.3.1 Checking Status of Outputs .................................................................................................. 13

7.3.2 Setting Common Interface .................................................................................................... 14

7.3.3 Setting the Parameters of Decoder ...................................................................................... 14

7.3.4. Setting the ASI1 Output ....................................................................................................... 15

7.3.5. Setting the ASI2/SDI Output ................................................................................................ 15

7.3.6. Setting the Mux/Filter........................................................................................................... 15

8. Manual for DCH-4000P-41S /-41T/-41C/-41S2 ................................................................................ 15

8.1 Menu Structure for DCH-4000P-41S /-41T/-41C/-41S2.............................................................. 15

8.2 Setting Inputs for DCH-4000P-41S /-41T/-41C/-41S2 ................................................................ 18

8.2.1 Checking Status of Inputs ..................................................................................................... 18

8.2.2 Setting the Tuner Parameters............................................................................................... 18

8.2.3 Setting the Ethernet Connector ............................................................................................ 18

8.3 Setting Outputs for DCH-4000P-41S /-41T/-41C/-41S2.............................................................. 19

9. Manual for DCH-4000P-42S /-42T/-42C/-42S2 ................................................................................ 19

9.1 Menu Structure for DCH-4000P-42S /-42T/-42C/-42S2.............................................................. 19

9.2 Setting Inputs for DCH-4000P-42S /-42T/-42C/-42S2 ................................................................ 21

9.3 Setting Outputs for DCH-4000P-42S /-42T/-42C/-42S2.............................................................. 22

9.3.1 Setting the Ethernet TS over IP output ................................................................................. 23

9.3.2 Other output settings for DCH-4000P-42S /-42T/-42C/-42S2 .............................................. 23

10. REMOTE MONITORING AND CONTROL...................................................................................... 23

10.1 Install HDMS to a PC................................................................................................................. 23

10.2 Connect to HDMS...................................................................................................................... 23

10.3 Login to HDMS .......................................................................................................................... 24

10.4 Add DCH-4000P-xx to HMDS.................................................................................................... 24

10.5 DCH-4000P-xx in HDMS ........................................................................................................... 24

10.6 Other Settings............................................................................................................................ 25

11. FAQ.................................................................................................................................................. 25

12. Appendix.......................................................................................................................................... 25

12.1 Specification............................................................................................................................... 25

DCH-4000P-xx series Receivers

- 1 -

WW.PBI-CHINA.COM

1. SAFETY

Please read this chapter before installation and use of the device

This equipment is provided with a protective earthing ground incorporated in the power cord.

The main plug shall only be inserted in a socket outlet provided with a protective earth contact.

Any interruption of the protective conductor, inside or outside the device, is likely to make the

device dangerous.

The device described in this manual is designed to be used by properly-trained personnel

only. Adjustment, maintenance and repair of the device shall be carried out by qualified

personnel.

No operator serviceable parts inside. Refer servicing to qualified personnel. To prevent

electrical shock, do not remove covers.

For the correct and safe use of the device, it is essential that both operating and servicing

personnel follow generally accepted safety procedures in addition to the safety precautions

specified in this manual.

Whenever it is likely that safety protection is impaired, the device must be made in-operative

and secured against unintended operation. The appropriate servicing authority must be

informed. For example, safety is likely to be impaired if the device fails to perform the

intended measurements or shows visible damage.

WARNINGS

zDo not use the equipment in moisture environment surroundings.

Avoid direct contact with water.

zNever place the equipment in direct sunlight.

zThe outside of the equipment may be cleaned using a lightly dampened cloth. Do not use

any cleaning liquids containing alcohol, methylated spirit or ammonia etc.

zFor continued protection against fire hazard, replace line fused only with same type.

DCH-4000P-xx series Receivers

- 2 -

WW.PBI-CHINA.COM

2. TECHNICAL INTRODUCTION

DCH-4000P-xx is a professional IRD with a variety of input (including DVB over ASI, IP,

QPSK, QAM, COFDM and DS3) and output (CVBS, SDI, ASI, DS3 and IP) combinations. An

appropriate IP port equipped as an option supports DVB over IP applications. LAN control

and monitoring are achieved with TCP/IP, SNMP and HDMS*.

(*Headend Devices Management System, a remote management software)

2.1 Features

zFully complies with MPEG-2, MP@ML and DVB-S/-T/-C standards

zIP input or output with UDP/RTP (optional)

zMulticast and Unicast on IP

zSupports PAL, NTSC or SECAM

zSupports various Conditional Access systems

zSDI video output with digital audio embedded

zTwo sets of independent ASI outputs

zAutomatic PMT update

zCompatible with Multiple De-encrypt CI modules

zDS3 I/O for TS (optional)

zSwitchable audio sound track

zTeletext VBI, EBU subtitle and DVB subtitle

zUpgradeable through LAN

zEasy-to-use LCD menu

2.2 Factory Options

DCH-4000P-xx series Receivers

- 3 -

WW.PBI-CHINA.COM

Figure 2.1 Factory Option list of DCH-4000P series

3. INSTALLATION

Warning:

This equipment is provided with a protective earthing ground incorporated in the power cord.

The main plug shall only be inserted in a socket outlet provided with a protective earth contact.

Any interruption of the protective conductor, inside or outside the instrument, is likely to make

the instrument dangerous. The type of main plugged shipped with each instrument depends

on the country of application.

Caution:

Do not connect AC power until you have verified that the line voltage is correct and the proper

fuses are installed. The equipment requires a power source of either 50/60 Hz at 110V or

50/60 Hz at 240V. The voltage ranges for these nominal voltage values are shown in the

table:

POWER REQUIREMENT

Input voltage 90-260 Vrms auto select

Frequency 47 to 63 Hz

Power 50 VA max. / 30 VA typical.

Current 110 V/0.27A or 240 V/0.125A typical

Caution:

Be sure the supply voltage is within the specified range.

Checking the fuses:

The recognized recommended fuses are size 5 by 20 mm, rate T 2.0A, 250 V (UL and IEC

approved).

The line fuse is housed in a small container besides the power connector on the rear panel.

To check the fuse, insert the tip of a screwdriver in the slot at the middle of the container and

pry gently to extend the fuse where there is a little tap and pull out the fuse gently. The fuse is

attached to the line module and cannot be removed.

3.1 Inspection and Test

Check if the devise has any visible damage. If everything seems all right, power can be

applied to the device. The main socket and fuse are located at the rear panel of the device.

When the device is turned on, verify that the display shows the following message:

DCH-4000P (factory default unit-name)

IP: 168.192.1.21 (factory default IP Address)

If no message is shown in the display or there is not light in the display, the device is

DCH-4000P-xx series Receivers

- 4 -

WW.PBI-CHINA.COM

defective and has to be returned for servicing.

3.2 Functional Self Test

No specific functional self test is needed.

The device has been factory tested according to recognized test procedures and is ready for

operation.

3.3 Mounting

The environment should be relatively dust free, free of excessive vibration and the ambient

temperature between 0 ℃to 40 ℃. Relative humidity of 20% to 80% (non-condensed) is

recommended.

Air intake for cooling is achieved via holes at the side of the device and the fans inside. The

air flow should not be obstructed. Therefore, the device has to be placed on a flat surface,

leaving some space at the sides of the device.

When in operation, the internal temperature should not exceed the limit of 70 ℃.

4. FRONT PANEL

4.1 Front Panel List

Figure 4.1 Front Panel of DCH-4000P-xx Series Receiver

4.2 Indicator LEDs

There are 3 LED-indicators:

-POWER: the status of the power supply

green: the power is turned on

off : the power is turned off

-TUNER LOCK: the status of the tuner

green: The incoming QPSK is locked by the tuner.

off : there is no QPSK input signal or the signal is unlocked

-ALARM: the status of input signal source, which includes IP input, QPSK signal input and

DVB-ASI TS input.

DCH-4000P-xx series Receivers

- 5 -

WW.PBI-CHINA.COM

4.3 Liquid Crystal Display

The 2 x 20 character Liquid Crystal Display (LCD) shows all the required information about

the selected parameters.

The top row of the LCD shows the selected parameter. The bottom row indicates the present

values and how these can be adjusted.

The parameters are grouped in three menus:

-the Inputs, which gives the full operation on inputs parameters

-the Outputs, with the full operation control functions on outputs parameters

-the Systems, gives the general device management parameters and informs about the

device working status

4.4 Keypad

Figure 4.2 Keypad of DCH-4000P-xx series

The 6 keys on the front panel allow you to navigate in the information given on the LCD and

to change parameters, when the device operates under local control.

The <ENTER>-key is used to enter the main menu or a sub-menu. When you stand on the

preferred menu, <ENTER> is used to active the parameter on the bottom line and allows you

to change the value. It also finishes the input of new alphanumeric values and confirms the

changes.

The <>-and< >-keys are used to select between the main menus or sub-menus. When

you stand on the preferred menu and the parameter is active, they are also used to change

the numerical values. Selecting a digit with the <>-and < >-keys.

The <EXIT>-key, is used to exit a menu without any action.

4.5 Common Interface

There are two Common Interface slots. You can insert up to two different CAM modules for

descrambling.

DCH-4000P-xx series Receivers

- 6 -

WW.PBI-CHINA.COM

5. REAR PANEL

Figure 3.2 Rear Panel of DCH-4000P-xx Series

B1 TS/IP Input/Output interface

B2 XRL L interface

B3 XRL R interface

B4 RGB/YUV interface (G/Y)

B5 RGB/YUV interface (B/U)

B6 RGB/YUV interface (R/Y)

B7 CVBS2 Output interface

B8, B18 ASI2/SDI output interface

B9, B19 ASI1 output interface

B17 ASI input interface

B10 RS-232 interface

B11 Tuner Loop Out interface

B12 Tuner In interface

B13 Power socket, AC 90~260V

B14 CVBS1 Output interface

B15, B16 L-Audio-R interface

B20 Ethernet interface for remote management system

B21 Grounding

5.1 Power Supply

The power cord is inserted to an IEC main socket at the side of the device.

Check that the power cord is suitable for the country where the device will be used.

A standard power cord with a European DIN 49441 two pin main plug is delivered together

with the device.

The line fuses are housed in a small container at the side of the power supply connector.

5.2 Output Connectors

The ASI interface B9), B19) and ASI2 interface B8), B18) are two pairs of independent ASI

output. Both use female BNC connectors, with 75 Ohm impedance. The ASI interface B18)

and B19) are used as a redundant output of B8) and B9) out.

DCH-4000P-xx series Receivers

- 7 -

WW.PBI-CHINA.COM

Note: the B8), B18) interface could be configured as SDI with Audio embedded. Please refer

to Chapter 7.3.5.

5.3 ASI Input Connector

The ASI input B17) is a 75 ohm female BNC connector.

5.4 RS-232 Interface

This interface is a 9-pins female sub-D connector. The RS-232 interface is only used for

factory software upgrade and configuration, so you are not allowed to connect any cable to

the RS-232 connector, as that could damage the device.

5.5 Ethernet Interface

An RJ-45 connector B20) provides a remote control interface.

5.6 TS/IP Interface (Factory Optional)

An RJ-45 connector B1) provides a streaming stream over IP input or output.

6. INSTALLATION

The device allows you to configure, control and monitor through the Keypad and front panel

display when a remote control system is not used.

6.1 Main Menu

Turn on the device and wait for 8 to 10 seconds, while the device will complete self inspection

and configuration. The top row of the LCD shows the name of the device. The local IP address is

displayed on the bottom row of the LCD.

Note: the local IP address can be changed in the System Menu.

Use the <ENTER>-key to enter on the Main Menu. The <>-and< >-keys are used to choose

between the three main menus.

Altri manuali per DCH-4000P

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PBI Convertitore multimediale

PBI

PBI DCH-4000P Manuale utente

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente