PCB Piezotronics IMI SENSORS HTTO640B31 Manuale utente

Model HTTO640B31

High Temperature 4-20 mA Output Velocity Sensor

Installation and Operating Manual

For assistance with the operation of this product,

contact PCB Piezotronics, Inc.

Toll-free: 800-959-4464

24-hour SensorLine: 716-684-0001

Fax: 716-684-3823

E-mail: [email protected]

Web: www.imi-sensors.com

The information contained in this document supersedes all similar information that

may be found elsewhere in this manual.

Total Customer Satisfaction –PCB

Piezotronics guarantees Total Customer

Satisfaction. If, at any time, for any

reason, you are not completely satisfied

with any PCB product, PCB will repair,

replace, or exchange it at no charge.

You may also choose to have your

purchase price refunded in lieu of the

repair, replacement, or exchange of the

product.

Service –Due to the sophisticated

nature of the sensors and associated

instrumentation provided by PCB

Piezotronics, user servicing or repair is

not recommended and, if attempted,

may void the factory warranty. Routine

maintenance, such as the cleaning of

electrical connectors, housings, and

mounting surfaces with solutions and

techniques that will not harm the

physical material of construction, is

acceptable. Caution should be observed

to insure that liquids are not permitted to

migrate into devices that are not

hermetically sealed. Such devices

should only be wiped with a dampened

cloth and never submerged or have

liquids poured upon them.

Repair –In the event that equipment

becomes damaged or ceases to

operate, arrangements should be made

to return the equipment to PCB

Piezotronics for repair. User servicing or

repair is not recommended and, if

attempted, may void the factory

warranty.

Calibration –Routine calibration of

sensors and associated instrumentation

is recommended as this helps build

confidence in measurement accuracy

and acquired data. Equipment

calibration cycles are typically

established by the users own quality

regimen. When in doubt about a

calibration cycle, a good “rule of thumb”

is to recalibrate on an annual basis. It is

also good practice to recalibrate after

exposure to any severe temperature

extreme, shock, load, or other

environmental influence, or prior to any

critical test.

PCB Piezotronics maintains an ISO-

9001 certified metrology laboratory and

offers calibration services, which are

accredited by A2LA to ISO/IEC 17025,

with full traceability to SI through

N.I.S.T. In addition to the normally

supplied calibration, special testing is

also available, such as: sensitivity at

elevated or cryogenic temperatures,

phase response, extended high or low

frequency response, extended range,

leak testing, hydrostatic pressure

testing, and others. For information on

standard recalibration services or

special testing, contact your local PCB

Piezotronics distributor, sales

representative, or factory customer

service representative.

Returning Equipment –Following

these procedures will insure that your

returned materials are handled in the

most expedient manner. Before

Warranty, Service, Repair, and

Return Policies and Instructions

returning any equipment to PCB

Piezotronics, contact your local

distributor, sales representative, or

factory customer service representative

to obtain a Return Warranty, Service,

Repair, and Return Policies and

Instructions Materials Authorization

(RMA) Number. This RMA number

should be clearly marked on the outside

of all package(s) and on the packing

list(s) accompanying the shipment. A

detailed account of the nature of the

problem(s) being experienced with the

equipment should also be included

inside the package(s) containing any

returned materials.

A Purchase Order, included with the

returned materials, will expedite the

turn-around of serviced equipment. It is

recommended to include authorization

on the Purchase Order for PCB to

proceed with any repairs, as long as

they do not exceed 50% of the

replacement cost of the returned

item(s). PCB will provide a price

quotation or replacement

recommendation for any item whose

repair costs would exceed 50% of

replacement cost, or any item that is not

economically feasible to repair. For

routine calibration services, the

Purchase Order should include

authorization to proceed and return at

current pricing, which can be obtained

from a factory customer service

representative.

Warranty –All equipment and repair

services provided by PCB Piezotronics,

Inc. are covered by a limited warranty

against defective material and

workmanship for a period of one year

from date of original purchase. Contact

PCB for a complete statement of our

warranty. Expendable items, such as

batteries and mounting hardware, are

not covered by warranty. Mechanical

damage to equipment due to improper

use is not covered by warranty.

Electronic circuitry failure caused by the

introduction of unregulated or improper

excitation power or electrostatic

discharge is not covered by warranty.

Contact Information –International

customers should direct all inquiries to

their local distributor or sales office. A

complete list of distributors and offices

can be found at www.pcb.com.

Customers within the United States may

contact their local sales representative

or a factory customer service

representative. A complete list of sales

representatives can be found at

www.pcb.com. Toll-free telephone

numbers for a factory customer service

representative, in the division

responsible for this product, can be

found on the title page at the front of this

manual. Our ship to address and

general contact numbers are:

PCB Piezotronics, Inc.

3425 Walden Ave.

Depew, NY14043 USA

Toll-free: (800) 828-8840

24-hour SensorLineSM: (716) 684-0001

Website: www.pcb.com

E-mail: [email protected]

PCB工业监视和测量设备 - 中国RoHS2公布表

PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table

部件名称

有害物质

铅(Pb)

汞

(Hg)

镉

(Cd)

六价铬(Cr(VI))

多溴联苯 (PBB)

多溴二苯醚(PBDE)

住房

PCB板

电气连接器

压电晶体

环氧

铁氟龙

电子

厚膜基板

电线

电缆

塑料

焊接

铜合金/黄铜

本表格依据 SJ/T 11364 的规定编制。

O：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

X：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。

铅是欧洲RoHS指令2011/65/ EU附件三和附件四目前由于允许的豁免。

CHINA RoHS COMPLIANCE

DOCUMENT NUMBER: 21354

DOCUMENT REVISION: C

ECN: 45605

Component Name

Hazardous Substances

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Chromium VI

Compounds

(Cr(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl

Ethers (PBDE)

Housing

PCB Board

Electrical

Connectors

Piezoelectric

Crystals

Epoxy

Teflon

Electronics

Thick Film

Substrate

Wires

Cables

Plastic

Solder

Copper Alloy/Brass

This table is prepared in accordance with the provisions of SJ/T 11364.

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement of GB/T 26572.

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials for this part is above

the limit requirement of GB/T 26572.

Lead is present due to allowed exemption in Annex III or Annex IV of the European RoHS Directive 2011/65/EU.

SENSORS

Model HT 640/641/645/646 B Series High Temperature 4-20mA SensorModel HT 640/641/645/646 B Series High Temperature 4-20mA Sensor

Operating Guide with Enclosed Warranty Information

3425 Walden Avenue, Depew, New York 14043-2495

Phone (716) 684-0003

Fax (716) 684-3823

Toll Free Line 1-800-959-4IMI

AND INSTRUMENTATION FOR MACHINE CONDITION MONITORINGAND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

MANUAL NUMBER: 31330

MANUAL REVISION: NR

ECN NUMBER:

SENSORS A

Table of Contents

ND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

Introduction...................................................................................................................... Page 3

General Features

Dimension Drawing......................................................................................................... Page 4

Operation and Wiring ...................................................................................................... Page 5

Standard Wiring

Taking Measurements

RV Option

TO Option

Installation....................................................................................................................... Page 9

Direct Adhesive Mount

Standard Stud Mount

Adhesive Stud Mount

Magnetic Mount

ESD Sensitivity............................................................................................................... Page 13

Warranty/Servicing

Warranty, Service & Return Procedure .......................................................................... Page 14

Customer Service........................................................................................................... Page 15

PAGE 2

SENSORS A

Introduction

ND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

The Model HT 640/641/645/646 B Series High Temperature 4-20mA Sensors combine the capabilities of a

piezoelectric vibration sensor and a 4-20mA vibration transmitter. The sensor outputs a 4-20mA signal that is

proportional to the overall velocity or acceleration of the machinery. Ideal for monitoring the vibration of process

equipment such as fans, motors and pumps, the output of the sensor is used for process control or predictive

maintenance. There are many options in this series. Please refer to specific specification sheets for further

details.

General Features

• Expanded Temperature Range from –40°C to +125°C

• Imbedded Piezoelectric Accelerometer for improved accuracy and frequency response.

• Vibration range can be in Acceleration or Velocity.

• Allows for continuous vibration monitoring of critical applications.

• Reduces sophisticated vibration analysis requirements.

• RV (Raw Vibration) option for conducting frequency analysis and machinery diagnostics.

• TO (Temperature Output) option via an independent 4-20mA loop.

• Readily interfaces to existing process control and predictive maintenance equipment.

• Rugged stainless steel construction for applications in harsh environments.

• Flexible design allows for various custom requirements.

PAGE 3

SENSORS A

Dimension Drawing

ND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

Inch (mm)

PAGE 4

SENSORS A

Operation and Wiring

ND INSTRUMENTATION FOR MACHINE CONDITION MONITORING

Standard Wiring

The Model 640/641/645/646 B Series operates from a standard 2-wire, 4-20mA loop. If using a loop powered

unit, attach the positive (+) input from the power supply to Pin A or Red wire on the sensor and the negative (-)

input from the power supply to Pin B or Blue wire of the sensor.

Figure 1 – wiring: loop powered Figure 2 – wiring: loop powered/DC source

If using a standard DC power supply, install either an ammeter and/or load resistor in line with the output, Pin B or

Blue wire.

The resistor will generate a DC voltage that is proportional to current by:

If R ohmsand I mA thenV VDC=

=500 6 3,

Note:

- Resistor value must be less than: (Vsupply – 12) x 50.

- For integral cable sensors: RED wire is positive, BLUE wire is negative.

PAGE 5

Indice

Altri manuali PCB Piezotronics Sensore di sicurezza

PCB Piezotronics

PCB Piezotronics ICP W138A25 Manuale utente

PCB Piezotronics

PCB Piezotronics 103B03 Manuale utente

PCB Piezotronics

PCB Piezotronics ICP 105C12/NC Manuale utente

PCB Piezotronics

PCB Piezotronics W138A05 Manuale utente

PCB Piezotronics

PCB Piezotronics 4115K-10A Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS Echo TO670A01 Manuale utente

PCB Piezotronics

PCB Piezotronics TORKDISC 5309D-02A Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS Echo TO670A02 Manuale utente

PCB Piezotronics

PCB Piezotronics ICP W138A06/-0012 Manuale utente

PCB Piezotronics

PCB Piezotronics 117B30 Manuale utente

PCB Piezotronics

PCB Piezotronics W105C02/018C10 Manuale utente

PCB Piezotronics

PCB Piezotronics 118B11 Manuale utente

PCB Piezotronics

PCB Piezotronics ICP W138A10/-0031 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI SENSORS M643A61 Manuale utente

PCB Piezotronics

PCB Piezotronics 4204-03A Manuale utente

PCB Piezotronics

PCB Piezotronics W109C12/038CY010AC Manuale utente

PCB Piezotronics

PCB Piezotronics IMI Sensors M641B12 Manuale utente

PCB Piezotronics

PCB Piezotronics IMI Sensors RV640B11 Manuale utente

PCB Piezotronics

PCB Piezotronics ICP W138A01/-0022 Manuale utente

PCB Piezotronics

PCB Piezotronics 138A06 Manuale utente

PCB Piezotronics

PCB Piezotronics 352A25/NC Manuale utente

PCB Piezotronics

PCB Piezotronics ICP 222B Manuale utente

PCB Piezotronics

PCB Piezotronics ICP JT352C33 Manuale utente

PCB Piezotronics

PCB Piezotronics M354C03 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente