Peak FCB4N Manuale utente

GUITAR AUDIO AND MIDI SWITCHING PRODUCTS

FCB4N

PROGRAMMABLE MIDI FOOT CONTROLLER

OWNER’S MANUAL

Document Rev.1.0.1

Nov.21.2008

www.pe k2005.com

INTRODUCTION

Overview

The FCB4N is progr mm ble MIDI foot controller th t supports ll st nd rd MIDI devices. You c n s ve

MIDI mess ges into the FCB4N with 64 presets memory. The MIDI mess ges c n be tr nsmit by 2 different

PC nd 4 CC in preset.

The FCB4N h s up/down b nk switches nd 4 p tches switches with high qu lity nd he vy duty foot switch

th t you c n feel when pressing on switch. The body is m de by luminum with bl ck nodize co ting nd

folded by l ser cutting process. It is comp ct rugged, simple to use nd fully progr mm ble MIDI foot

controller.

TOP Panel

BANK UP/DOWN SWITCH This is using for incre se b nk up or decre se b nk down from the current

st te. The current b nk is st rt from b nk#1 up to b nk#32 m ximum but

you c n progr m the b nk limit for looping.

PRESETS SWITCH The FCB4N h s 4 p tches in b nk s P1, P2, P3 nd P4. You lso use

these switches in progr mming mode for edit, enter, s ve or c ncel

function.

BANK/PROGRAM DISPLAY The seven segment displ y h s 2 digits displ y for showing mode when you

re entering to edit/setting progr m or displ y b nk number when you re

on oper tion. The MIDI number is st rt from 0 to 127 th t me ns the

number would be show from 00 to 2.7. If number is over 99 it would be

show the number with point.

BACK Panel

MIDI OUT This MIDI out port is for tr nsmit MIDI mess ges from the unit to other

MIDI device.

12VAC/DC I/O Connect to supply extern l volt ge 9 - 12V c/dc with current 200mA

minimum. (12V c/dc m ximum) These re 2 ports for exp nd the input

power supply to other MIDI device. (It is not power supply ports)

Specification

• 1 MIDI OUT with 5-pin DIN connector.

• 2 b nk switches, 4 p tch switches with he vy duty foot switch.

• 8 f ctory def ult mode select ble for midi progr m ch nge mess ges. (mode F1 - F8)

• 1 progr mm ble mode for configure midi progr m ch nge mess ges. (mode U1)

• 1 progr mm ble mode with 64 presets, rr nged in 16 b nks of 4 presets (mode U2)

• Progr m Ch nge nd Continuous Controller mess ge support (2 PC nd 4 CC mess ges per preset,

ll on different MIDI ch nnels)

• Flexible power requirements: 9V-12V, AC or DC, 200mA d pter with 5.5mm/2.1mm b rrel

connector. (Ad pter is not included)

• Housed in sleek luminum ch ssis nd brushed finish with bl ck nodize co ting.

• Dimensions pprox. : 10.3"W x 4.7"D x 2.0"H (26.2cm x 12.0cm x 5.0cm)

• Weight pprox. : 1.5lb (0.7kg)

Power connecting

The FCB4N is Flexible power requirements 9V-12V, AC or DC, 200mA. So, you c n plug in power supply to

12VAC IO port (selected one) then the unit is re dy to works. For nother one is power out with the s me

volt ge/current s the input d pter.

Above picture is n ex mple th t using POD 2.0 power supply with the FCB4 unit.

FCB4N PRESET MODE

The FCB4N h s f ctory def ult presets mode F1 – F8 nd U1 – U2 mode for users setting.

Factory default mode F1 – F8

The F ctory def ult presets mode cont ins mode F1 – F8 h ve different B nk tot lly nd MIDI PC# st rts.

This setting is completely setting for user th t me ns you just select preset mode which you w nt nd

choose MIDI ch nnel. Th t’s re dy to control your MIDI device in progr m ch nge function.

MODE F1

B nk r nk: B nk#1 – B nk#4

MIDI Progr m Ch nge r nk: PC#0 – PC#15

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l = 16 Presets.

MODE F2

B nk r nk: B nk#1 – B nk#4

MIDI Progr m Ch nge r nk: PC#1 – PC#16

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l = 16 Presets.

MODE F3

B nk r nk: B nk#1 – B nk#9

MIDI Progr m Ch nge r nk: PC#0 – PC#35

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l = 36 Presets.

MODE F4

B nk r nk: B nk#1 – B nk#9

MIDI Progr m Ch nge r nk: PC#1 – PC#36

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l = 36 Presets.

MODE F5

B nk r nk: B nk#1 – B nk#20

MIDI Progr m Ch nge r nk: PC#0 – PC#79

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l = 80 Presets.

MODE F6

B nk r nk: B nk#1 – B nk#20

MIDI Progr m Ch nge r nk: PC#1 – PC#80

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l = 80 Presets.

MODE F7

B nk r nk: B nk#1 – B nk#32

MIDI Progr m Ch nge r nk: PC#0 – PC#127

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l = 128 Presets.

MODE F8

B nk r nk: B nk#1 – B nk#32

MIDI Progr m Ch nge r nk: PC#1 – PC#127 nd b ck to PC#0

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l = 128 Presets.

User define mode U1 – U2

MODE U1

You c n set the r nk of b nk nd MIDI progr m ch nge st rting number.

B nk r nk: B nk#1 – B nk#32

(select ble but def ult is B nk#32)

MIDI Progr m Ch nge st rt: PC#0 – PC#127

(select ble but def ult is PC#0)

MIDI Ch nnel: CH#1 – CH#16

(select ble but def ult is CH#1)

Tot l preset is up to user setting.

MODE U2

This mode is for progr mming MIDI mess ges into e ch preset memory. You c n progr m MIDI

mess ges with 2 progr m ch nges nd 4 continuous control ch nges.

PC1 MIDI Ch nnel#: CH#1 – CH#16

(select ble but def ult is CH#1)

PC1 Progr m Ch nge#: PC#0 – PC#127

(select ble but def ult is PC#0)

PC2 MIDI Ch nnel#: CH#1 – CH#16

(select ble but def ult is CH#2)

PC2 Progr m Ch nge#: PC#0 – PC#127

(select ble but def ult is PC#0)

CC MIDI Ch nnel#: CH#1 – CH#16

(select ble but def ult is OFF)

CC1 Controller#: CC#0 – CC#127

(select ble but def ult is OFF)

CC1 Control V lue#: 0 – 127

(select ble but def ult v lue is 0)

CC2 Controller#: CC#0 – CC#127

(select ble but def ult is OFF)

CC2 Control V lue#: 0 – 127

(select ble but def ult v lue is 0)

CC3 Controller#: CC#0 – CC#127

(select ble but def ult is OFF)

CC3 Control V lue#: 0 – 127

(select ble but def ult v lue is 0)

CC4 Controller#: CC#0 – CC#127

(select ble but def ult is OFF)

CC4 Control V lue#: 0 – 127

(select ble but def ult v lue is 0)

B nk r nk: B nk#1 – B nk#16

Tot l Preset: 64 Presets

MIDI Implementation

MIDI Ch nnel: Def ult: 1

(Tr nsmitted) Ch nged: 1 - 16

Progr m Ch nge#: 0 – 127 c n be setting up to 2 progr m ch nge mess ges

tr nsmitted per preset. (With different MIDI ch nnel)

Controller#: 0 – 127 c n be setting up to 4 controllers with tr nsmitted per

preset. (With CC MIDI ch nnel)

Control Ch nge V lue: 0 – 127 setting v lue in e ch controller.

BASIC OPERATION

Ple se refer to text th t ppe rs s under switches when you re going to use the FCB4N unit in the b sic

oper tion mode. On power up, the l test preset is selected nd tr nsmitted MIDI mess ge vi MIDI out.

(Initi l v lue is B nk#1, preset#1 of mode F1)

You c n not progr m or set ny ch nges on preset when you re working on n oper tion mode bec use

we design the firmw re to h ve no del y when the FCB4N tr nsmitted MIDI mess ges vi MIDI out. The

MIDI mess ges re suddenly tr nsmitted once the selected preset is pressing.

Bank and Preset selection

In e ch mode h s different tot l b nk on the function but h s 32 B nks m ximum. (B nk#1 – B nk#32)

Press BANK UP or BANK DOWN switches to move/scroll from the current b nk to nother. The

BANK/PROGRAM displ y will fl sh nd h s no MIDI mess ge tr nsmitted until preset switch is selected.

(P1, P2, P3 or P4 switches) You c n hold on the BANK UP or BANK DOWN switches to/p st the current

b nk continuous nd the BANK/PROGRAM displ y will be looping once it is out of limit.

You c n selected preset by press the P1, P2, P3 or P4 switches then the selected preset LED bove the

switch will be on with MIDI mess ge suddenly tr nsmitted.

SETUP MODE AND PRESET PROGRAMMING

When you supplied power into the FCB4N unit then it is going to l unch oper tion mode utom tic lly. You

c n not progr m or setting on this oper ting mode. You should tell the unit knows th t you w nt to setting

or progr mming. This ch pter is expl in how to progr mming or setting the FCB4N

Programming Mode Enable

You h ve to en ble the progr mming mode every time when you need to setting/progr mming on FCB4N.

You c n en ble the progr mming mode by step following

1. Remove power from the FCB4N unit.

2. Press P1 switch nd hold on.

3. Plug the power into the FCB4N unit.

4. The BANK/PROGRAM displ y will show s ch r cters below

5. The BANK/PROGRAM displ y s ch r cters bove is me ning

“Progr mming Mode En ble”

then rele se the P1 switch.

6. The FCB4N will be initi lizing with progr mming mode en ble so, you c n progr m the unit

follow by the next ch pters.

7. You c n dis ble the preset progr mming mode by simply remove the power plug out from

unit.

Preset Mode Selection

The FCB4N h s 10 presets mode so you c n select e ch preset mode to m tching with your MIDI devices.

You c n select preset mode by step following:

1. M ke sure you re lre dy en bled the progr mming mode.

(Ple se see Progr mming Mode

En ble ch pter)

2. Press P1 switch nd hold until the BANK/PROGRAM displ y is fl shing current preset mode.

The def ult setting is mode F1 so, the BANK/PROGRAM displ y should be fl shing s

ch r cters below:

3. Once the BANK/PROGRAM displ y is fl shing current mode then rele se the P1 switch.

4. You c n select preset mode which you w nt by scroll to/p st vi BANK DOWN or BANK UP

switches. The BANK/PROGRAM displ y is fl shing s ch r cters below:

5. After you’ve selected preset mode then press P2 switch to confirm.

6. If you h ve selected F ctory Def ult Mode (F1 – F8) the next step is going to MIDI ch nnel

selection. Otherwise ple se see the next ch pter.

7. The BANK/PROGRAM displ y will be showing ch r cters “CH” for 1 second nd will be

fl shing current MIDI ch nnel. (Def ult MIDI ch nnel is 1) So, the BANK/PROGRAM displ y

is fl shing s ch r cters below:

8. You c n select MIDI ch nnel from 1 – 16 by scrolling to/p st vi BANK DOWN or BANK UP

switches. The BANK/PROGRAM displ y is fl shing s ch r cters below:

9. After you’ve selected MIDI ch nnel then press P4 switch to s ve the setting into memory.

The FCB4N will goes out from the preset mode setting nd b ck to the oper tion mode with

progr mming mode en bled.

10. If you w nt to b ck to the preset mode selection p ge (m in menu) ple se press P2 switch.

11. You c n c ncel or exit setting by press P3 switch. The FCB4N will goes out from the preset

mode setting nd return b ck to the oper tion mode with progr mming mode en bled.

Note You c n press P1 switch to see the current setting topic/menu.

BANK UP

BANK

OWN

User define Mode U1 Setting

This mode is supported only MIDI progr m ch nge (s me s mode F1 – F8) but you c n set tot l BANK limit

nd you c n lso set the progr m ch nge number st rt.

You c n set the FCB4N to U1 mode by step following:

1. M ke sure you re lre dy en bled the progr mming mode.

(Ple se see Progr mming Mode

En ble ch pter)

2. Press P1 switch nd hold until the BANK/PROGRAM displ y is fl shing current preset mode.

(Ple se see Preset Mode Selection ch pter)

3. After you h ve selected U1 mode nd BANK/PROGRAM displ y is fl shing “U1” then press

P2 switch to enter U1 mode nd setting p r meter s below:

4. Select MIDI ch nnel th t you w nt to tr nsmit mess ges once the BANK/PROGRAM displ y is

showing “CH” for 1 second then it will show you the current MIDI ch nnel. You c n select from

01 – 16 for setting MIDI ch nnel.

5. If you h ve selected MIDI ch nnel then press P2 switch to scroll up the setting menu.

6. The BANK/PROGRAM displ y is showing “SP” for 1 second then it will show you the current

st rt MIDI progr m ch nge number. You c n select from 00 – 2.7 for setting the st rt progr m

ch nge number. (If number is over 99 then it will show in point)

7. If you h ve selected MIDI PC# st rt then press P2 switch g in to scroll up the setting menu.

8. The BANK/PROGRAM displ y is showing “tb” for 1 second then it will show you the current

tot l b nk. You c n select b nk# from 1 – 32 for setting how m ny b nks do you w nt.

9. After you’ve completed setting then press P4 switch to s ve the setting into memory. The

FCB4N will goes out from the preset mode setting nd return b ck to the oper tion mode with

progr mming mode en bled.

10. If you w nt to return b ck to the preset mode selection p ge g in ple se press P2 switch.

11. You c n c ncel nd exit setting by press P3 switch. The FCB4N will goes out from the preset

mode setting without s ving ny ch nges nd return b ck to the oper tion mode with still in

progr mming mode en bled.

Note You c n press P1 switch to see the current setting topic/menu.

P2 for enter selected or scroll up

BANK UP / DOWN for select setting

Mode U1

MIDI Ch nnel#

St rt PC#

Tot l B nk

User define Mode U2 Setting

U2 mode is using for progr mming MIDI continuous mess ges with 2 PC nd 4 CC. You c n ON/OFF or

setting mess ges you w nt to tr nsmit. U2 mode h s 64 presets memory with 16 b nks x 4 p tches so, you

c n set/progr m MIDI continuous mess ges by step following:

1. Select preset th t you w nt to edit only in b nk#1 – b nk#16 by press BANK UP or BANK

DOWN switches to move/scroll from the current b nk to nother. If b nk# you selected is over

b nk#16 it will set to b nk#16 utom tic lly. If b nk you selected is not enough ple se set

the FCB4N to mode F5 before progr mming preset.

2. After you selected preset lre dy then go to mode U2 by following

Preset Mode Selection

ch pter.

M ke sure you re lre dy en bled the progr mming mode.

(Ple se see Progr mming

Mode En ble ch pter)

3. After you selected U2 mode nd BANK/PROGRAM displ y is fl shing “U2” then press P2

switch to enter U2 mode nd setting p r meter s below:

Mode U2

PC1: MIDI Ch nnel

PC1: PC#

PC2: PC#

PC2: MIDI Ch nnel

CC: MIDI Ch nnel

C1: Controller#

C2: Controller#

C3:

Controller#

C4: Controller#

C1: CC V lue

C2: CC V lue

C3: CC V lue

C4: CC V lue

BANK UP / DOWN for select setting

P2 for

enter selected or

scroll up

Indice

Altri manuali Peak Accessori

Peak

Peak PCAN-USB Hub Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente