peerless-AV KLR62232 Manuale utente
12019-06-14 #:150-9227-1
ENG
KLR62232, KLR64255
22019-06-14 #:150-9227-1
Symbols
ENG
WARNING
ENG
#
Skip to step.
ENG
Do not overtighten screws.
ENG
ENG - This product is designed to be installed on wood stud, solid concrete or cinder block walls. Hardware is
included for wood stud, solid concrete and cinder block installation. Do not begin to install product until you have
read and understood the instructions and warnings contained in this user guide. Before installing make sure
the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly
secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum
Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This
product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal
injury. Be careful not to pinch ngers when operating the mount. To reduce the risk of electric shock or re, do not
expose product to water or moisture. Be sure power cord is routed so that it will not be tripped on, stepped on,
or pinched by heavy items. Avoid overloading electrical outlets or extension cords. Always disconnect the power
cord from the power outlet when installing, servicing, or not using the product for an extended period of time. Do
not block ventilation slots or fan exhaust on product. Blocking airow could damage product. Arrange product to
allow air to ow freely around product. Keep product away from direct sunlight or any source of heat. For support
please call 800-4-SIGNAGE.
WARNING
32019-06-14 #:150-9227-1
Tools Needed for Assembly.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
5/32"
(4mm)
5/16"
(8mm)
3/8"
(10mm)
42019-06-14 #:150-9227-1
A (1)
enclosure B (1)
wall mount
G (1)
hook-on
bracket
F (1)
locking bracket
Parts List KLR62232
Part #
KLR64255
Part #Description Qty
Aenclosure 1 152-1544 152-1545
Bwall mount 1 ST635 ST640
C#14 x 2-1/2" wood screw 4 5S1-015-C03 5S1-015-C03
D8mm concete anchor 4 590-0320 590-0320
Epower strip 1 600-0370 600-0370
Flocking bracket 1 152-T1502 152-T1511
Ghook on bracket 1 152-T1508 152-T1520
HM5 x 20mm 3 510-1065 510-1065
Parts (Before beginning, make sure you have all parts shown below).
ENG
E (1)
power strip
52019-06-14 #:150-9227-1
D (4)
8mm concrete anchor
C (4)
#14 x 2-1/2" wood screw
H (3)
M5 x 20mm
1
B
Follow and complete instructions for included wall
mount.
ENG
62019-06-14 #:150-9227-1
2
B
A
Hold enclosure over display in desired location,
and make sure that it is level. Mark the top
location of the enclosure.
ENG
3
Remove display.
ENG
Loosen.
ENG
4mm
72019-06-14 #:150-9227-1
4
4a
4a
4b
ENG - When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that
the wood studs are a minimum of 2" x 4" nominal size. Do not install over gypsum board thicker than 5/8".
WARNING
Wood stud wall.
ENG Concrete/Cinder block.
ENG
4a-1 Use stud nder to locate and
mark stud center lines.
ENG
82019-06-14 #:150-9227-1
4a-2
⅛"
G
B
G
B
Mark mounting holes on stud center lines.
Mounting holes should be positioned 1/8" under
the horizontal cover line.
ENG
cover line
ENG
cover line
ENG
92019-06-14 #:150-9227-1
5
4a-4
3/8"
(10mm)
4a-3
5/32"
(4mm)
C (2)
G
B
Mounting hole must center on stud.
ENG
2.5"
(64mm)
5/32"
(4mm)
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
Level wallplate. Install using wood screws provided.ENG
Maximum 80 in. • lb (9 N.M.).
ENG
10 2019-06-14 #:150-9227-1
4b-1
4b
G
4b-2
5/16"
(8mm)
ENG - When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum
compressive strength of 2000 psi. When installing Peerless wall mounts on a cinder block wall, the cinder blocks
must meet ASTM C-90 specications and have a minimum nominal width of 8". Do not drill into mortar joints!
Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. It is
suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breaking out the back of the hole when entering a void or cavity. Never attach concrete expansion anchors to
concrete or cinder block covered with plaster, drywall or other nishing material.
WARNING
Mark mounting holes on stud center lines.
Mounting holes should be positioned 1/8" under
the horizontal cover line.
ENG
cover line
ENG
2.5"
(64mm)
5/16"
(8mm)
Do not drill into mortar joints.
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
cover line
ENG
B
⅛"
G
B
cover line
ENG
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali peerless-AV Rack e supporto
peerless-AV
peerless-AV ACC215 Manuale utente
peerless-AV
peerless-AV SR555E Manuale utente
peerless-AV
peerless-AV Smartmount ST24D Guida
peerless-AV
peerless-AV DS-S555-3X3 Manuale utente
peerless-AV
peerless-AV PSTK-600 Manuale utente
peerless-AV
peerless-AV SA752PU Guida
peerless-AV
peerless-AV SUA740P Manuale utente
peerless-AV
peerless-AV SMARTMOUNT WSP756 Manuale utente
peerless-AV
peerless-AV 0735029322108 Manuale utente
peerless-AV
peerless-AV IMAM Manuale utente
peerless-AV
peerless-AV DCT Series Manuale utente
peerless-AV
peerless-AV DS-VW765-LQR Manuale utente
peerless-AV
peerless-AV STP680 Manuale utente
peerless-AV
peerless-AV DS-VW655-2X2 Manuale utente
peerless-AV
peerless-AV LCT620AD Guida
peerless-AV
peerless-AV SR860-EUK Manuale utente
peerless-AV
peerless-AV ACC973 Manuale utente
peerless-AV
peerless-AV MOD-PRGSKIT100 Manuale utente
peerless-AV
peerless-AV MOD-FPP2 Manuale utente
peerless-AV
peerless-AV KIL740-EUK Manuale utente
