peerless-AV WBK100 Guida
Visit the Peerless Web Site at www.peerlessmounts.com
Installation and Assembly:
WALL PLATE ACC KIT FOR PSTA-%, PSTK-%
Models:
ISSUED: 03-23-09 SHEET #:055-9262-1
WBK100,
WBK100-W
AB
ED
C
IMPORTANT: Read instruction sheet before you start installation and assembly.
NOTE: Some parts may appear slightly different than illustrated.
1Select model of projector wall arm. Secure wall arm (sold separately) to wall plate (A) using four carriage bolts (E)
and lock nuts (D).
PSTA-028, PSTA-028-W
PSTK-028, PSTK-028-W PSTA-2955, PSTA-2955-W
PSTK-2955, PSTK-2955-W
A
E
D
A
E
D
SoldSeparately SoldSeparately
WBK-100 WBK-100-W
Description Qt
y
. Part # Part #
A
wall plate 1 055-1923 055-2923
B#14 x 2.5 phillips hex head wood screw 4 5S1-015-C03 5S1-015-C04
Cconcrete anchor 4 590-0320 590-0320
Dlock nut 4 530-1016 530-2016
Ecarriage bolt 4 520-9207 520-2047
Parts List
Visit the Peerless Web Site at www.peerlessmounts.com 2 of 3 ISSUED: 03-23-09 SHEET #:055-9262-1
B
A
Installation to Wood Stud Walls
Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended.
Based on its edges, draw a vertical line down the stud's center. Place wall plate (A) on wall as a template. Mark
the center of the four mounting holes. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Secure wall plate
(A) to wood stud using four #14 x 2-1/2" wood screws (E) as shown. Skip to Step 3 of universal projector wall
arm.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs or joists.
Installers are responsible to provide hardware for other types of mounting situations.
WARNING
2
Visit the Peerless Web Site at www.peerlessmounts.com 3 of 3
Installation to a concrete or cinder block wall
Drill four 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach wall plate (A) using four concrete
anchors (C)and four #14 x 2 -1/2" wood screws (B) as
shown in Illustration A and 1, 2, and 3. Tighten all
fasteners.
3
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the screws, greatly
reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
or other finishing material. If mounting to concrete
wall covered with plaster/drywall is unavoidable,
plaster/drywall (up to 5/8" thick) must be
counterbored as shown right. If plaster/drywall is
thicker than 5/8", custom fasteners must be supplied
byinstaller.
WARNING
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual con-
crete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a
solid part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90
specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached
hardware and components.
B
C
Illustration A
A
ISSUED: 03-23-09 SHEET #:055-9262-1
1
3
2
Tighten all fasteners.
concrete
surface
C
UTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
concrete concrete
Drill holes and insert anchors
Place wall plate over anchors and secure with screws
B
B
A
C
C
C
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali peerless-AV Rack e supporto
peerless-AV
peerless-AV DS-VW765-LQR Guida
peerless-AV
peerless-AV SR560-FLIP2 Manuale utente
peerless-AV
peerless-AV DS-S555-3X2 Manuale utente
peerless-AV
peerless-AV SPL746 Manuale utente
peerless-AV
peerless-AV MOD-FPSKIT Manuale utente
peerless-AV
peerless-AV DSF210-GFC Manuale utente
peerless-AV
peerless-AV EPT650 Guida
peerless-AV
peerless-AV DSF210-GHC Manuale utente
peerless-AV
peerless-AV ACCXT201 Guida
peerless-AV
peerless-AV ACCXT400 Guida
peerless-AV
peerless-AV PWV240/BK Guida
peerless-AV
peerless-AV DS-VW765-LAND Manuale utente
peerless-AV
peerless-AV ACC975 Manuale utente
peerless-AV
peerless-AV EWP-OH85F Manuale utente
peerless-AV
peerless-AV HPF650 Manuale utente
peerless-AV
peerless-AV SF680-HUB Manuale utente
peerless-AV
peerless-AV Videowall Mount PD02VW 46 55 L Guida
peerless-AV
peerless-AV SF632-S Manuale utente
peerless-AV
peerless-AV ESA746PU Guida
peerless-AV
peerless-AV LCW620AD Guida
