PEERLESS Mounts SmartMount RTFPA-220 Guida
Installation and Assembly:
SmartMount™ Articulating LCD Wall Arm
Models: SA740P, SA740P-S, RTFPA-220, RTFPA-220I, RTFPA-220S, RTFPA-220SI,
902220, SWV250/BK, SWV250/SI
Features:
•Fits 22" - 40" (56 - 102 cm) LCD screens
• Three tensionable pivot points for extensive adjustment of viewing angle
• VESA®75/100/200 x 100/200 x 200 compatible
• Frees up space by folding flat against the wall
• Keeps electronic wires routed internal to reduce clutter Max Load Capacity: 80 lb (36.3 kg)
©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2
ISSUED: 02-05-09 SHEET #: 202-9323-1
2 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall................................................................................................................................................4
Installation to Solid Concrete and Cinder Block .....................................................................................................................5
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
•drill
• 5/16" (8 mm) bit for concrete and cinder block wall
• 5/32" (4 mm) bit for wood stud wall
• level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit
• Brick Contact Qualified Professional
• Other or unsure? Contact Qualified Professional
WARNING
3 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
A
M
N
SWV250/SI
SWV250/BK RTFPA-220S
RTFPA-220 SA740P-S
SA740P RTFPA-220I 902220 RTFPA-220SI
Description Qty. Part # Part # Part # Part #
Awall mount 1 095-0376 095-0376 095-0378 095-0378
Bconcrete anchor 2 590-0320 590-0320 590-0320 590-0320
C11 mm retaining spacer 4 590-5005 590-5005 590-5003 590-5003
D1/4-20 x 13 mm flat head phillips screw 2 520-1209 520-1209 520-2178 520-2178
EM4 x .7 x 10 mm phillips screw 4 504-9012 504-9012 520-2027 520-2027
FM4 x .7 x 20 mm phillips screw 4 504-9020 504-9020 504-2014 504-2014
GM6 x 1 x 12 mm phillips screw 4 520-1128 520-1128 520-2039 520-2039
H#14 x 63.5 mm flat head wood screw 2 520-1202 520-1202 520-2165 520-2165
IM6 x 1 x 20 mm phillips screw 4 520-9402 520-9402 520-2040 520-2040
JM6 x 1 x 30 mm phillips screw 4 510-9109 510-9109 520-2042 520-2042
KM5 x 1 x 6 mm phillips screw 5 520-1023 520-1023 520-2214 520-2214
L#10 flat washer 4 540-9400 540-9400 540-9442 540-9442
Mhook bracket 1 095-1346 095-1346 095-4346 095-4346
Nadapter plate 1095-1322 095-1322 095-4322 095-4322
O#10-32 x 6 mm flat head phillips screw 1 520-1108 520-1108 520-2108 520-2108
Pinstallation kit (not shown) 1 n/a 200-8570 n/a 200-8570
Parts List
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
B
E
H
C
FG
I
J
O
D
KL
4 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
Installation to Wood Stud Wall
Remove cord covers from wall arm assembly (A) as shown in figure 1.1. Using a stud finder, locate and mark the
edges of the wood stud used in mounting this product. Use of an edge to edge stud finder is highly recommended.
Use a level to draw a vertical line down the center of the stud. Use wall plate as template to mark center of holes
along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Attach wall mount (A) to wall using two
#14 x 63.5 mm flat head wood screws (H) as shown in figure 1.2.
Skip to step 2 on page 6.
WOOD
STUD
WALL
A
H
fig. 1.2
CORD COVER
A
fig. 1.1
1
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations (not UL approved).
WARNING
5 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
Installation to Solid Concrete and Cinder Block
Remove cord covers from wall arm assembly (A)
as shown in figure 1.1. Level and use wall plate as
template to mark center of holes. Drill two 5/16"
(8 mm) dia. hole to a minimum depth of 2.5" (64
mm). Insert anchors (B) in holes flush with wall.
Place wall mount (A) over anchor and secure with
wood screw (H). Make sure wall mount is level, and
tighten all fasteners.
A
H
B
WALL PLATE
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a
solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90
specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
WARNING
• Concrete anchors are not intended for attachment
to concrete wall covered with a layer of plaster,
drywall, or other finishing material as shown below.
If mounting to concrete wall covered with plaster/
drywall is unavoidable, plaster/drywall (up to 5/8"
thick) must be counterbored as shown below.
Be sure concrete anchors do not pull away from
concrete when tightening screws. If plaster/drywall is
thicker than 5/8", custom fasteners must be supplied
by installer (not UL evaluated).
WARNING
1
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall plaster/
drywall
concrete concrete
1
3
2
B
Drill holes and insert anchors (B).
Place plate (A) over anchors (B) and secure with screws (H).
Tighten all fasteners.
A
B
H
concrete
surface
SOLID CONCRETE CINDER BLOCK
6 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
L
M
N
K
N
E
G
N
Attaching Adapter Plate to Screen with VESA 200 x 100 or 200 x 200 Mounting
Pattern
Attach hook bracket (M) to adapter plate (N) using
four M5 x 6 mm screws (K) and #10 washers (L) as
shown.
2
FOR VESA 200 x 100 MOUNTING PATTERN:
Choose hole pattern as shown below. Attach
adapter plate (N) to back of screen using four M4 x
10 mm screws (E) as shown below.
*NOTE: If screw (E) gets less than three threads
of engagement, attach adapter plate (N) to back of
screen using four M4 x 20 mm screws (F) and four
spacers (C) as indicated below.
Skip to step 3 on page 9.
FOR VESA 200 x 200 MOUNTING PATTERN:
Choose hole pattern as shown below. Attach adapter
plate (N) to back of screen using four M6 x 12 mm
screws (G) as shown below.
*NOTE: If screw (G) gets less than three threads
of engagement, attach adapter plate (N) to back of
screen using four M6 x 20 mm screws (I). If screw (I)
still gets less than three threads of engagement, use
four M6 x 30 mm screws (J).
Skip to step 3 on page 9.
*For screens with a
hole pattern in a pocket,
spacers (C) go between
adapter plate (N) and
screen.
NOTE: For VESA 75 mm and 100 mm patterns, see
following page.
2-1
• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not
tightly secured, damage may occur to screen or product may fail.
WARNING
C
7 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
Attaching Hook Bracket to Screen with VESA 75 or 100 Mounting Pattern
C
*For screens with a
hole pattern in a pocket,
spacers (C) go between
hook bracket (M) and
screen.
FOR VESA®75 MOUNTING PATTERN:
Choose hole pattern as shown below. Attach hook
bracket (M) to back of screen using four M4 x 10 mm
screws (E) as shown below.
*Note: If hole pattern is in a pocket, attach hook
bracket (M) to back of screen using four M4 x 20 mm
screws (F) and four retaining spacers (C) as indicated
below.
E
FOR VESA 100 MOUNTING PATTERN:
Choose hole pattern as shown below. Attach hook
bracket (M) to back of screen using four M4 x 10
mm screws (E) as shown below.
E
2
M
M
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
8 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
FOR INSTALLING TO PEERLESS LC MODEL ADAPTER BRACKET
For screen compatibility please refer to the LCD or plasma interface list on our website www.peerlessmounts.com or
call customer care for a screen specific adapter bracket LC or PLP models (not UL evaluated).
FOR INSTALLING TO PEERLESS PLP MODEL ADAPTER BRACKET
GENERIC ADAPTER BRACKET
M5 X 10 MM SCREW
Note: Refer to LC model adapter bracket instruction sheet for attachment of adapter bracket to screen.
Note: Either M5 x 6 mm or M5 x 10 mm screws are included with the LC model adapter bracket.
Attach hook bracket (M) to adapter bracket using four M5 x 6 mm or M5 x 10 mm screws.
Note: Refer to PLP model adapter bracket instruction sheet for attachment of adapter bracket to screen.
Note: M5 x 10 mm screws are included with the PLP model adapter bracket
Attach hook bracket (M) to adapter bracket using four M5 x 10 mm screws.
2
2
M
GENERIC ADAPTER BRACKET
M5 X 6 MM OR M5 X 10 MM SCREW
M
9 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
Adjust tension knob on side of mount shown in
figure 4.1 to desired tension to balance your screen
size and weight.
Push or pull from top or bottom of screen to adjust
tilt as shown. The tilt can be adjusted to a maximum
of 15° forward or 5° backward.
4
• Be careful not to pinch fingers when opening and
closing mount from the wall.
CAUTION
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
CAUTION TENSION KNOB
fig. 4.1
Roll screen to desired position (5° clockwise or
counter-clockwise). Insert #10-32 x 1/2" flat head
phillips screw (O) to lock screen into position as
shown in figure 4.2. fig. 4.2
O
To attach screen to wall mount (A), lower hook
bracket (M) with screen at an angle into pockets of
wall mount as shown in figure 3.1. Once clips are
engaged, push down to seat clips in pockets as
shown in figure 3.2. Insert and tighten M5 phillips
screw (K) to lock screen to wall mount as shown in
figure 3.3.
To remove screen from mount, loosen screw (K)
and lift screen off of mount.
Installing and Removing Flat Panel Screen
3
M
SCREEN
K
A
fig. 3.1 fig. 3.2
fig. 3.3
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 20 in. • lb (2.26 N.M.) maximum torque.
CAUTION
• Do not lift more weight than you can handle. Use ad-
ditional man power or mechanical lifting equipment
to safely handle placement of the screen.
• Failure to lock hook bracket (M) with screw (K) can
cause screen to come off mount if hit accidentally.
WARNING POCKET
CLIP
4-1
10 of 20 ISSUED: 02-05-09 SHEET #: 202-9323-1
6
• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the
screen to fall.
WARNING
Note: Make sure cords have enough slack to allow full movement of the arm.
Route cords inside arm slots of wall mount (A) as shown in figure 5.1. Optional: Run power cord through one side
of mount and signal cable(s) through other side in order to avoid interference with the signal.
Lock cords into place by sliding cord covers onto mount as shown in figure 5.2. Screen may have to be moved for
better access for sliding on the cord covers.
fig. 5.1
A
fig. 5.2
5
CORD COVER
TENSION SCREWS
ARM TENSION ADJUSTMENT: If more or less tension is desired in the arm pivot points, do the following:
• To increase tension, turn tension screw(s) clockwise with allen wrench.
• To reduce tension, turn tension screw(s) counter-clockwise with allen wrench.
NOTE: Do not turn more than half a turn.
© 2009, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
3215 W. North Ave.
Melrose Park, IL 60160
www.peerlessmounts.com
Questo manuale è adatto per i seguenti modelli
8
Indice
Lingue:
Altri manuali PEERLESS Mounts Supporto TV
