PEERLESS Paramount PRT2X2 Manuale utente
ISSUED: 11-25-09 SHEET #: 202-9413-1
Paramount™ Tilt Mount
for 10" - 37" LCD Screens
Max UL Load Capacity: 115 lb (32 kg)
Model: PRT2X2
Installation Guide
©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2
This product was designed to be installed on wood stud walls and solid concrete (2000 psi
density minimum) or cinder block walls. Before installing make sure the supporting surface will
support the combined load of the equipment and hardware. Screws must be tightly secured. Do
not overtighten screws or damage can occur or product may fail. Never exceed the Maximum UL
Load Capacity. This product is intended for indoor use only. Use of this product outdoors could
lead to product failure or personal injury. For support please call customer care at 1-800-865-2112.
WARNING
2 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
Tools Needed for Assembly
recommended)
block wall
D(2)E(2)
M4 x 10 mm
F(4)
M4 x 20 mm
G(4)H(4)
M5 x 6 mm
M(4)N(4)
M6 x 12 mm
J(4)
M6 x 20 mm
K(4)M6 x 30 mm
L(4)
B(1)
A(1)
C(1)
3 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
Installing to Wall
1
Use wall mount (A) as a template, make sure it is level, and mark two mounting holes along the
(A) and attach to wall with two wood screws (D
WOOD STUD
A
D
TOP CUTAWAY VIEW
Wood screws must
center in stud.
STUD
D
A
WARNING
Do not over tighten screws, or
damage may occur.
WARNING
TOP CUTAWAY VIEW
4 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
Installing to Solid Concrete or Cinder Block
1
Level wall mount (A
E) into holes and secure wall
mount (A) with two wood screws (D
CINDER
BLOCK
SOLID
CONCRETE
A
D
E
5 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, gener-
hole instead of a hammer drill to avoid breaking out the back of the hole when entering a
void or cavity.
directly to load-bearing concrete.
WARNING
1
2
E
A
E
D
concrete
A) over anchors (E). Secure with screws (D). Tighten screws.
Drill holes and insert anchors (E).
WARNING
CUTAWAY VIEW
wall plate
drywall
wall plate
drywall
CORRECT
INCORRECT
concrete
concrete
6 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
FOR VESA®75 MOUNTING PATTERN:
NOTE: ®200 x 100 mm and 200 x 200 mm hole patterns, see page 8.
B) to back of screen using four
M4 x 10 mm screws (F) as shown below.
*NOTE: If hole pattern is in a pocket, attach mounting plate (B) to back of screen using four
M4 x 20 mm screws (G) and four retaining spacers (H) as indicated below.
Skip to step 4.
Attaching Mounting Plate to Screen with VESA 75 or 100 Mounting Pattern
2
in the screen inserts or if screws bottom
out and bracket is still not tightly secured,
damage may occur to screen or product
may fail.
WARNING
F
B*For screens with a
hole pattern in a pocket,
spacers (H) go between
adapter plate (B) and
screen. H
7 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
FOR VESA®100 MOUNTING PATTERN:
B) to back of screen using four
M4 x 10 mm screws (F) as shown below.
Skip to step 4.
2
in the screen inserts or if screws bottom
out and bracket is still not tightly secured,
damage may occur to screen or product
may fail.
WARNING
FB
8 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
B) to adapter plate (C) using four M5 x 6 mm screws (M) and four
#10 washers (N) as shown.
Attaching Adapter Plate to Screen with VESA 200 x 100 or 200 x 200
Mounting Pattern
3
N
B
C
M
C
F*For screens with a hole
pattern in a pocket, spacers
(H) go between adapter plate
(C) and screen. H
FOR VESA 200 x 100 MOUNTING PATTERN:
C) to back of screen using four
M4 x 10 mm screws (F) as shown below.
*NOTE: If screw (F) gets less than three threads of engagement, attach adapter plate (C) to
back of screen using four M4 x 20 mm screws (G) and four spacers (H) as indicated below.
Skip to step 4.
3-1
in the screen inserts or if screws bottom
out and bracket is still not tightly secured,
damage may occur to screen or product
may fail.
WARNING
9 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
FOR VESA 200 x 200 MOUNTING PATTERN:
C) to back of screen using four
M6 x 12 mm screws (J) as shown below.
*NOTE: If screw (J) gets less than three threads of engagement, attach adapter plate (C)
to back of screen using four M6 x 20 mm screws (K). If screw (K) still gets less than three
threads of engagement, use four M6 x 30 mm screws (L).
in the screen inserts or if screws bottom
out and bracket is still not tightly secured,
damage may occur to screen or product
may fail.
WARNING
3-2
J
C
10 of 51 ISSUED: 11-25-09 SHEET #: 202-9413-1
B) onto phillips hex head screws on wall plate (A) as
NOTE: Sides of mounting plate (B) must be outside of wall plate (A) on both sides as shown
Installing and Removing Flat Panel Screen
4
force. Overtightening can cause damage
to mount.
CAUTION
SCREEN
A
B
SLOT
SCREEN
SIDES OF MOUNTING
B) ON OUTSIDE
A)
Indice
Lingue:
Altri manuali PEERLESS Rack e supporto
PEERLESS
PEERLESS IWB600-WB Manuale utente
PEERLESS
PEERLESS HCACC503 Manuale utente
PEERLESS
PEERLESS Perfect Mount PMF2X2 Manuale utente
PEERLESS
PEERLESS IMC 18 Guida
PEERLESS
PEERLESS HCW101 Manuale utente
PEERLESS
PEERLESS RTPLA 50 Guida
PEERLESS
PEERLESS Solid-Point PLB 1 Guida
PEERLESS
PEERLESS ACC951 Guida
PEERLESS
PEERLESS IM740P Guida
PEERLESS
PEERLESS Smartmount SA752PU Guida
PEERLESS
PEERLESS Smartmount D-FPF-220 Guida
PEERLESS
PEERLESS PJF2-UNV Guida
PEERLESS
PEERLESS SAL730P Guida
PEERLESS
PEERLESS AEC0609 Guida
PEERLESS
PEERLESS Solid-Point PS 1 Guida
PEERLESS
PEERLESS MIS 213 Guida
PEERLESS
PEERLESS ACC 604 Guida
PEERLESS
PEERLESS SUF650P and assembly Guida
PEERLESS
PEERLESS PTT188743 Series Manuale utente
PEERLESS
PEERLESS HT642-002 Guida
