PEERLESS Solid-Point PLCM UN1 Guida
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
1 of 9 ISSUED:09-07-07 SHEET #: 202-9199-1
Read instruction sheet before you start installation and assembly.
Model:PLCM UN1,
PLCM UN1 CP
Installation and Assembly - Solid•Point™Flat Panel Straight
Column Mount
R
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
• Installer must verify that the ceiling will safely support
thecombinedweightofallattachedequipmentand
hardware.
WARNING
Note: Installation for 32"-50" LCD and Flat Panel Screens
Model Max. Load Screen Size Range
PLCM UN1 125 lb. (56.7 kg.) 32'' - 50''
PLCM UN1 CP 125 lb. (56.7 kg.) 32'' - 50''
PLCM UN1PLCM UN1 CP
ISSUED:09-08-07 SHEET #: 202-9199-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
2 of 9
• Donot begin to install your Peerless productuntil you have read and understood theinstructions and warnings
containedin this Installation Sheet. If you have anyquestions regarding any of the instructions or warnings,please
callPeerlesscustomercareat1-800-729-0307.
• Thisproductshouldonly be installed by someone of good mechanical aptitude, and fully understands
these instructions.
• NeverexceedtheMaximumULLoadCapacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrewsfirmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• Installermustverifythatthe ceiling will safely support the combined weight of all attached equipment and hardware.
WARNING
Table of Contents
Parts List..............................................................................................................................................................................3
InstallingCeilingPlate(modelPLCM-UN1-CPonly)..............................................................................................................4
Installing Flat Panel Straight Column Mount to ceiling ..........................................................................................................5
InstallingAdapterPlate .........................................................................................................................................................6
InstallingAdapterPlate to Screen.....................................................................................................................................7, 8
Installation of Screen to Flat Panel Straight Column Mount ..................................................................................................9
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
3 of 9 ISSUED:09-07-07 SHEET #: 202-9199-1
A
B
Note: Some parts may
not appear exactly as illustrated.
HI
C
E
J
#10washer (8)
540-9400
M4 x 10 mm(8)
520-1156
1/2"spacer(4)
540-1015
M8 x 40 mm (4)
520-1152
M5 x 12 mm (8)
520-1064
M8 x 15 mm (6)
520-1068
K
L
N
D
M
F
Description Qty Part #
Aceiling arm box 1 201-1062
Btilt bracket 1 200-1552
C33" support pipe 1 139-1088
Dretaining collar 1 1800-375
EM5 x 10 mm penta-pin™ screw 4 505-9010
F2.875 OD x 2.125 ID x .062 H fiber washer 1 540-9432
GM10 x 15 mm penta-pin screw 8 520-9263
HM10 x 2" penta-pin tool 1 520-9260
IM5 x 1" penta-pin tool 1 520-9249
JM5 x 8 mm phillips screw 4 520-1167
Kadapter bracket 1 200-0333
Lvertical bracket 2 200-1302
M10-32 x 3/8" socket pin serrated washer head screw 4 520-1151
N4 mm security allen wrench 1 560-9646
Before you begin, make sure all parts shown are included with your product.
PARTS LIST
1/4"washer(6)
540-9440
M8 x 25 mm (4)
520-1101
Adapter Bracket Fasteners
M6 x 12 mm (6)
520-1050
R
Q
GP
Additional parts for model PLCM-UN1-CP only
PARTS LIST
Description Qty. Part #
EM5 x 10 mm penta-pin™ screw 1 505-9010
P#14 x 2.5 wood screw 4 5S1-015-C03
Qend cap 2 2PT-22CA01D
Rceiling bracket 1 128-1039
ISSUED:09-08-07 SHEET #: 202-9199-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
4 of 9
Q
R
ACC210
For Concrete Ceilings drill four 5/16" (8 mm)
dia. holes to a minimum depth of 1 3/4" (45
mm). Attach ceiling plate (R) using concrete
expansionanchorsas shown in 1-1 and 1-2.
Then snap end caps (Q) into place.
Align hole in ceiling plate with hole in ceiling.
Gentlyhammerinconcreteanchor.
Use a 10 mm wrench to tighten concrete
anchor to 80 in • lb (9 N.M.) maximum torque
toexpandanchors.
FORPRODUCTSAFETYUSE ONLYRAWL™
#5005OR HILTI™HL814CONCRETE
ANCHORS.Order accessory kit #ACC 210
which contains four .312 x 1.625
(8 mm x 41 mm) concrete expansion
anchors.
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattachconcreteexpansionanchorstoconcrete
coveredwithplaster,drywall,orotherfinishingmaterial.
WARNING
For Wood Joist Finished Ceiling, Exposed
Wood Joists, or Wood Beam Ceiling. Drill four
5/32" (4 mm) dia. holes to a minimum depth of 2.5"
(64 mm) INTO JOIST CENTERS.Attachceiling
plate (R) with four #14 x 2.5" (6 mm x 65 mm) wood
screws (P) using a 3/8" (10 mm) socket wrench.
Tighten wood screws (P) so ceiling plate is firmly
attached. Snap end caps (Q) into place.
Q
R
P
• Tighten wood screws so that ceiling plate is firmly
attached,butdonot overtighten. Overtightening can
damagescrews,greatlyreducingtheir holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the joists. The use of an "edge to edge" stud
finderishighlyrecommended.
WARNING
Skip to page 5 for PLCM-UN-1
CONCRETE
PLASTER/
DRYWALL
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
5 of 9 ISSUED:09-07-07 SHEET #: 202-9199-1
ceiling plate (included with PLCM-UN1-CP)
Threadsupport pipe(C)intothreadedfittinginceilingplate (UL ListedCMJ470, includedwith PLCM-UN1-CP).
Tighten - four or five complete turns - leaving slot aligned with one small hole in the side of the ceiling plate
threadedfitting.Insertand tighten one M5 x 10 mm penta-pin screw (E) provided with ceiling plate as shown. Use
the M5 penta-pin tool (I) to tighten screw. BY HAND, insert four M10 x 1.5 x 15 mm penta-pin screws (G) into
threaded holes in the sides of ceiling arm box (A). Leave approximately 1/4" of exposed thread. Slide ceiling arm
box(A)andfiberwasher(F)ontoendofsupportpipe(C).Threadretainingcollar(D)ontothreadedendofsupport
pipe (C). Tighten - four or five complete turns. Slide ceiling arm box (A) down so that it is on top of retaining collar
(D). Insert and tighten one M5 x .8 x 10 mm penta-pin screw (E) into retaining collar (D) as shown. Insert one M5
penta-pin screw (E) through the tab on the back of ceiling arm box (A). Use M5 penta-pin tool (I) to tighten screw
just enough to stabilize support pipe (C).
Note: UL Listed ADJ or EXT extension columns series can be used in combination with, or in place of support
pipe(C)toachievedifferentlengths.
E
D
C
C
A
F
D
G
1/4”
G
E
BACKOF CEILING
ARMBOX
2
Installing Flat Panel Straight Column Mount to ceiling
E
ISSUED:09-08-07 SHEET #: 202-9199-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
6 of 9
Slide vertical brackets (L) onto c-channels as shown below. Refer to the table on the last page of the screen
compatibility chart to determine the proper assembly of the vertical bracket (L). For standard bracket mounting, see
figure3.1. For reverse bracket mounting, seefigure 3.2.
Example: For a Toshiba model 50 HP82 50" screen, assemble the vertical bracket (L)as shown in figure 3.2 below
(reversebracket mounting).
K
L
fig. 3.2
Bracket Mounting: Reverse
K
L
fig. 3.1
Bracket Mounting: Standard
c-channel
c-channel
To assemble the adapter bracket (K) to your flat screen product, please refer to the compatibility chart and configurations
table on accompanying screen compatibility chart. First, locate your flat screen product in the compatibility chart using the
manufacturers name and model number. Next, note the configuration letter shown in the far right hand column. Finally, use
theconfigurations table, which appears after the compatibility chart, to determine the correct mountinghardware for your
flatscreen product.
Installing Adapter Plate
3
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
7 of 9 ISSUED:09-07-07 SHEET #: 202-9199-1
Attach tilt bracket (B) to adapter bracket (K) using four M10 x 15 mm penta-pin screws (G) as shown below.
4
Set a cloth on the floor to prevent scratching the screen. Place the screen on the floor face down. If the screen has
knobs on the back, remove them. Place adapter bracket (K) on the center of the screen. Slide the vertical brackets
(L) along the c-channels of the adapter bracket (K) until the slots on the back of the vertical brackets (L) are aligned
to the holes on the back of the screen. Fasten vertical brackets (L) to c-channels using four10-32 x 3/8" socket pin
serratedscrewhead(M).
Note: Do not fully tighten the screws (M) to allow the adapter bracket to slide along the vertical brackets (L) freely.
5
L
L
M
c-channel
K
Installing Adapter Plate to Screen
G
B
K
PORTRAIT
GB
K
LANDSCAPE
ISSUED:09-08-07 SHEET #: 202-9199-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
8 of 9
Slide the vertical brackets (L) along the c-channels of the adapter bracket (K) until the slots on the back of the
vertical brackets (L) are aligned to the holes on the back of screen. Fully tighten the four 10-32 x 3/8" socket pin
serrated screw head (M) which hold the vertical brackets (L) to the c-channels. Refer to the accompanying screen
compatibility chart to determine the proper fasteners to use.Attach the assembled adapter bracket to the back of
the screen using screws, upper and lower spacers as pictured. Verify that all holes are properly aligned, then use
the security allen wrench (N) to tighten the screws.
Note: See figure 6 below for slot sizes.
Example: For a Toshiba model 50 HP82 50" screen, attach the vertical brackets (L) to the screen using eight
M4 x 10 mm serrated socket pin screws or M5 x 12 mm socket pin screws through the small slots on the vertical
brackets (L). Please refer to the corresponding configuration note for more details. Upper spacers are required for
thisconfiguration.
6
fig. 6
Mounting Slots
SMALLSLOTSAREUSED
FORM4ANDM5SCREWS.
LARGESLOTSAREUSED
FORM6ANDM8SCREWS.
SCREWS
UPPERSPACERS
LOWERSPACERS
C-CHANNEL
K
MOUNTINGSLOTS:
LARGE
MOUNTINGSLOTS:
SMALL
L
M
Installation of Screen to Flat Panel Straight Column Mount
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
9 of 9 ISSUED:09-07-07 SHEET #: 202-9199-1
Attach tilt bracket (B) to ceiling arm box (A) by sliding the tilt bracket (B) over four M10 x 15 mm socket pin serrated
washer head screw (G) as shown below. Set desired tilt and tighten all fasteners.
Note: Wall not shown for clarity.
7
G
A
B
©2007PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Solid•Pointis atrademark ofPeerless Industries,Inc.
Allotherbrand andproductnames aretrademarks orregisteredtrademarks oftheirrespective owners.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali PEERLESS Rack e supporto
PEERLESS
PEERLESS SmartMount SP740P Guida
PEERLESS
PEERLESS PWMT300 Manuale utente
PEERLESS
PEERLESS Paramount PPF Guida
PEERLESS
PEERLESS MSA-301 Guida
PEERLESS
PEERLESS Paramount PSP2 Guida
PEERLESS
PEERLESS LMAM1940 Guida
PEERLESS
PEERLESS PWS211 Guida
PEERLESS
PEERLESS WSP700 Manuale di istruzioni
PEERLESS
PEERLESS SmartMount ST 635 Guida
PEERLESS
PEERLESS Mobile Videowall Trolley PDVWM 2x2 46 55 L Guida
PEERLESS
PEERLESS A100IWBMOUNT Guida
PEERLESS
PEERLESS IM740P Guida
PEERLESS
PEERLESS SmartMount ST 630P Guida
PEERLESS
PEERLESS DMU50SM Guida
PEERLESS
PEERLESS SmartMount SF650 Guida
PEERLESS
PEERLESS SGLS01 Guida
PEERLESS
PEERLESS SmartMount D-FPF-320 Guida
PEERLESS
PEERLESS WSP700 Manuale di istruzioni
PEERLESS
PEERLESS CMJ 470W Guida
PEERLESS
PEERLESS HCACC503 Manuale utente
