Pella 6000 Manuale di istruzioni
Hardware
Kit(s)
Loose Parts
(In Roll-up)
Loose
Parts
Lay door flat.
Before discarding the carton, make sure ALL parts are
accounted for -- check in carton roll-ups.
Carton
Roll-up
Carton
Roll-up
The carton material is recyclable
Phillips
Screwdriver #2
Pencil Power Drill with
3/32” drill bit
Tape Measure
12
Tools required
Scissors
Follow the steps in order, from 1 to 35.
Legend
RED objects are the action items for that step.
Steps in BLUE apply to LEFT HINGE configurations ONLY.
(Hinge side will be determined in a later step.)
Steps in GREEN apply to RIGHT HINGE configurations ONLY.
(Hinge side will be determined in a later step.)
Insert
MUST READ! Instructions in this box style are IMPORTANT!
13
2
NEW
Installation
Procedure.
Follow this manual for
a fast and proper
installation.
Part Number: 33258
Read the legend below in order to easily follow along and install your storm door.
For reference, the storm door assembly is illustrated on page 2.
Owner’s Guide and Installation Manual
PELLA®EXPRESS INSTALL™STORM DOOR MODELS
To order replacement parts, call
1-800-374-4758
or visit us at
www.pella.com
Please have your registration number
ready when you contact us either by
telephone or on the internet.
NOTE TO THE INSTALLER: This Owner's Guide and Installation Manual is the property of the
homeowner. Please leave it with the homeowner upon completion of the installation.
TROUBLE SHOOTING GUIDE
is located on page 12 of this manual
For safety reasons, the assistance of a second person is recommended when handling the door.
Storm Door Components NOTE: Actual door styles may vary from illustrations, however, the installation steps will be the same.
Screen
Glass
Glass/Screen
Retainer Strips
Screw Cover Strips
Latch Mounting Frame
Hinge
Mounting
Frame
Top
Mounting
Frame
Header
Frame Hardware Kit
Door Closers
Includes mounting
screws and some
handle components
Handle Kit
Includes handle
hardware with
separate instruction
sheet
Installation
Instructions
Bottom
Expander
Door
Registration
Number
© 2004 Pella Corporation All Rights Reserved
This is your door’s
identification number.
Leave this sticker on
your door.
2
de
Shim on YOUR hinge side - see Step 6
on Page 3, to determine your hinge
side.
LEFT
HINGE
doors,
shim this
side
Hinge
Shim
bc
a
Measure gap.
Gap
f
RIGHT
HINGE
doors,
shim this
side
Shim may be one long piece or small 8” to
12” sections.
NOTE: small sections must fully support the
hinges on the mounting frame.
Use an appropriate shim thickness to
reduce the gap in step C, to 1/4” or less.
Household shim materials may include paint stir
sticks or wooden yardsticks.
Slide Tight
If this gap is ...
LESS than 1/4”,
Go to START on page 3
1/4” or GREATER,
Go to Step d, to shim
Note: if this gap is over 9/16”,
a custom storm door is required.
Nail shims in place.
Note: If you removed an older
storm door, you may wish to
paint and cover any existing
holes before proceeding.
Go to START on page 3.
Shim
Shim must not
extend beyond
entryway face
Before you Begin Follow steps a, b and c to verify your entryway opening requirements.
Locate header
frame. Slide to one side of the entryway.
Right Hinge
Orientation
viewed from outside
Le Hinge
Orientation
viewed from outside
LEFT HINGE
Watch for this color
throughout the manual
RIGHT HINGE
Watch for this color
throughout the manual
3
Center in Opening
S
I
D
E
V
I
E
W
Align
outer
edges
Remove
glass
and
screen
Remember
this is the
INTERIOR SIDE
of the door
Lift
Snap
Determine the side you want your door to hinge.
FIRST, center
header frame in
entryway
opening ...
... THEN,
align with face
of brickmold.
Predrill the
two holes.
Secure with
jamb screws.
START
Your Installation
1
2
Continued
on page 4
35
6
Turn door
over.
Remove
shipping
clips.
Remove glass
and screen.
4
“Jamb Screw Bag”
unpainted
#8 x 3/4” Pan Head
Qty.2
Drill 3/32”
Pilot Holes
Factory
Drilled
Holes
This is
the TOP
of Your
Door
Inside
Facing
UP
Remove any protective film.
Slide boom expander
tight onto boom of door.
Secure with screws
(Bag taped inside expander).
#6 x 1/2” Pan Head
(Extra screw provided)
Qty. 2
Use a HAND
Screwdriver
8
9
4
Continued from Page 3
7
Position door for
LEFT hinge or
RIGHT hinge.
RIGHT HINGE DOORS
position metal plate
on this side.
10
Place
installation
support block
on door’s
HINGE side.
Left Hinge
Right Hinge
Left Hinge
Illustration
Inside
Facing
UP
This is
the TOP
of Your
Door
LEFT HINGE DOORS
position metal plate
on this side.
Slide
Slide
Right
Hinge
Illustrated
Continued
on page 5
Raise Up, Slide Over,
then Lower
Right
Hinge
Illustrated
Continued from
Page 4
5
RIGHT HINGE
Doors Only
SLIDE To This Side
LEFT HINGE
Doors Only
SLIDE To This Side
11
Set door in opening
(resting on boom spacer from step 10).
Hold tight to hinge side.
“Mounting Frame Screw Bag”
unpainted
#6 x 1” Pan Head
Qty. 5
Drill 3/32”
Pilot Holes
12
Predrill the five hinge
side hole locations.
Secure with screws.
Open the door.
Predrill the eight holes.
Secure with screws.
“Jamb Screw Bag”
unpainted
#8 x 3/4” Pan Head
Qty.8
Drill 3/32”
Pilot Holes
13
Continued on Page 6
O
p
e
n
Left Hinge
Illustration
Remove and discard
installation support
block.
14
Remove
and
Discard
Left Hinge
Illustration
Right
Hinge
Illustrated
Installation
Support Block
Right
Hinge
Illustrated
Left Hinge
Illustration
Remove and
Discard
Set
in
Place
P
Horizontal
Retainer
Strip
Install
Both
Top
and
Bottom
Install horizontal strips
first (top then bottom)
Vertical
Retainer
Strip
Install Both
Left and
Right
Continued on Page 7
Continued
from
Page 5
16
17
15
6
Predrill the five hole locations.
Secure with screws.
Cut shipping strap.
Remove “Do not cut” label.
Install glass
panel.
IMPORTANT:
Hold glass in
place while
installing retainer
strips.
Secure with
retaining strips.
“Mounting Frame Screw Bag”
unpainted
#6 x 1” Pan Head
Qty. 5
Drill 3/32”
Pilot Holes
Remove the two
yellow clips.
Re-install the
screws.
Reinstall
Remove
and
Discard
Leave this
plate in
place
Right
Hinge
Illustrated
18
19
20
21
Continued from page 6
Position top
mounting frame.
Note: if you have
interference with
siding, remove the
break-off tab with a
pliers, then caulk along
the back surface, for
protection from rain.
7
Go to the separate
hardware instruction
sheet in the handle kit
Install
your
handle
set.
Hardware
Instruction
Sheet
Handle Kit
Close door.
Rest mounting frame
on door.
Predrill the two
hole locations.
Secure with screws.
Left Hinge
Illustration
Factory
Installed
Spacer
Rest
on
Door
Remove the two spacers.
Break-off Tab
(Remove if necessary)
Factory
Installed
Spacer
Remove and Discard
“Mounting Frame Screw Bag”
unpainted
#6 x 1” Pan Head
Qty.2
Drill 3/32”
Pilot Holes
22
Top
Closer
Location
(Right Hinge)
Bottom
Closer
Location
(Right Hinge)
Approx.
1-1/2”
Approx.
1-1/2”
Right
Hinge
Illustrated
Left Hinge
Illustration
Top
Closer
Location
Bottom
Closer
Location
R
e
m
o
v
e
Align Arrow
with Notch on
Mounting Frame
Rest Against
Back of
Mounting
Frame
MOUNTING FRAME
Right Hinge
Illustrated
Align
Arrow
with
Notch on
Mounting
Frame
Rest Against Back of
Mounting Frame
Interior
Side
of the
Door
RIGHT HINGE Install Closers
on This Side.
LEFT HINGE Install Closers
on This Side.
25
26
24
Continued
from
Hardware
Instruction
27
8
Continued on Page 9
Hole Plugs
Break off of closer base
Qty.2
23
Predrill holes (3/32” bit).
Secure with screws.
Align closer base arrow with
small notch on mounting frame
(install both top and boom).
Break off alignment tabs.
Determine which
side to install the
closers
[Right versus Le].
Remove the two hole plugs
from the closer bases.
Insert into the factory
drilled holes near the top
corners of the door.
“Closer Screw Bag”
Unpainted #10 x 1” Pan Head
Qty. 4 each
Drill 3/32”
Pilot Holes
Adjustment
Screw
Remove
and
Discard
Right Hinge
Illustration
S
l
i
d
e
Discard
Insert
Remove
Leave Clip
in Place
Factory
Drilled
Holes
Bottom Closer: Rotate so
Touch ‘n Hold™ Button
Points Up
Touch ‘n Hold™
Button
TOP
Closer
BOTTOM
Closer
To Use:
Open the door,
then tap the button.
To Close:
Nudge the door
open slightly.
Touch ‘n Hold™
Button
Discard clips
(top and boom).
Bottom
Closer
with Touch ‘n Hold™
Button
Top
Closer
9
32
31
Slide top and boom closers onto
their bases.
Rotate boom closer as shown.
Adjust closer speed
with adjustment screw.
33
29
Continued
from
Page 8
Continued on Page 10
28
Locate
the top
and
boom
closers.
Left Hinge
Illustration
Top
Closer
Bottom
Closer
Close door.
Secure door bracket
with screws.
30
Pin door bracket onto closer
assembly.
“Closer Screw Bag”
color matched to door
#10 x 5/8” Pan Head
Qty. 2 each
Right
Hinge
Illustrated
F
a
s
t
e
r
-
S
l
o
w
e
r
Angled Edge
Points Away
From Door
Insert Angled
Edge
S
n
a
p
i
n
P
l
a
c
e
A
d
j
u
s
t
Sweep
Sill
Loosen to Adjust,
then Retighten
Set
In
Place
S
P
Horizontal
Retainer
Strip
Install
Both
Top
and
Bottom
Horizontal Strips
Go In First
Vertical
Retainer
Strip
Install Both
Left and
Right
Continued
from page 9
34
35
Hint: With the angled edge in place, run your finger down the length of the inner edge to snap in place.
10
Install screw cover strips
(1 Horizontal, 2 Vertical).
Close door.
Adjust boom
expander to lightly
contact the sill.
Glass or Screen Operation
To Install:
Hold the glass or
screen in place and
insert the top then
boom horizontal
strips first, then the
verticals.
To Remove:
Remove the vertical
strips first, then the
horizontals, by pulling
the corners away from
the door frame.
IMPORTANT: Hold
the glass in place
before removing the
top retaining strip.
Finished
with the installation. See page 11 for care and maintenance.
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Pella Porta
Pella
Pella V981553 Manuale utente
Pella
Pella 81CM0100 Manuale utente
Pella
Pella 801W0103 Manuale utente
Pella
Pella 81AK0101 Manuale utente
Pella
Pella architect series Manuale utente
Pella
Pella 81DU0100 Manuale utente
Pella
Pella 808SQ102 Manuale utente
Pella
Pella 818L0100 Manuale utente
Pella
Pella 80KM0103 Manuale utente
Pella
Pella V983492 Manuale utente
