Pentair IntelliBrite Manuale utente

IntelliBrite Controller Installation and User’s Guide

PRINTED ON: 7/29/2009, 600054_ctlg pics.SLDASM

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTALLATION

AND

USER’S GUIDE

INTELLIBRITE®CONTROLLER

(FOR INTELLIBRITE POOL, SPA AND LANDSCAPE

LIGHTING FIXTURES)

IntelliBrite Controller Installation and User’s Guide

P/N 619751 - Rev E9/2018

IntelliBrite Controller Installation and User’s Guide

WARNINGS AND IMPORTANT SAFETY PRECAUTIONS

IMPORTANT NOTICE

Attention Installer: This manual contains important information

about the installation, operation and safe use of this product.

This information should be given to the owner and/or operator

of this equipment.When installing and using this electrical

equipment, basic safety precautions should always be followed,

including the following:

IMPORTANT SAFETY INSTRUCTIONS PERTAINING

TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS. READ AND FOLLOW ALL INSTRUCTIONS.

DANGER! RISK OF ELECTRIC SHOCK,WHICH CAN

RESULT IN SERIOUS INJURY OR DEATH. Before

attempting installation or service, ensure that all power to

the circuit supplying power to the system is disconnected/

turned off at the circuit breaker.

Grounding (earth bonding) is required.The IntelliBrite®

Controller should be installed by a qualiﬁed professional

and grounded.

Read Safety Precautions and Important Instructions.

Before attempting any electrical wiring, be sure to read

and follow Safety Instructions. Wiring should only be

performed by a qualiﬁed professional.

Before installing this product, read and follow all warning

notices and instructions which are included. Failure to follow

safety warnings and instructions can result in severe injury,

death, or property damage. Call (800) 831-7133 for additional

free copies of these instructions.

Do not use this product to control an automatic pool cover.

Swimmers may become entrapped underneath the cover.

IntelliBrite Controller Installation and User’s Guide

WARNINGS AND IMPORTANT SAFETY PRECAUTIONS

Be sure the pool electrical system conforms with all requirements of the

National Electrical Code (NEC), and all local codes and ordinances. A licensed

or certiﬁed electrician must install the electrical system to meet or exceed those

requirements before the IntelliBrite®Controller is installed.The electrician should

also consult the local building department regarding local codes. Some of the

NEC requirements are listed below:

• The IntelliBrite Controller must be installed by a qualiﬁed electrician,

according to the National Electrical Code (including article 680) or

Canadian Electrical Code (including section 68) and, local code

requirements.For Canadian installations, supply circuit must be

protected by a ground fault circuit interrupter.

• The IntellilBrite Controller must be provided with a fail-proof ground

as required by NEC, Article 680 and any applicable local codes For

Canadian installations, the supply circuit must be protected by a

ground fault circuit interrupter.

• Do not install the IntelliBrite Controller within 5 feet (3 meters

for Canadian installations) of any body of water. USE COPPER

CONDUCTORS ONLY.

• The IntelliBrite Controller should be mounted at least 1 foot above the

water and ground level.

• Do not exceed the maximum ratings of individual components, wiring

devices, and current carrying capacity of conductors.

• For grounding and bonding the IntelliBrite Controller and the

installation, refer to section 680 of the National Electrical Code or

section 68 of the Canadian Electrical Code.

• The lighting circuit must have a Ground Fault Circuit Interrupter

(GFCI), and an appropriately rated circuit breaker.

• The light ﬁxture and all metal items within ﬁve (5) feet of the pool

must be properly electrically bonded.

• The IntelliBrite Controller must be properly electrically bonded and

grounded.

• Do not submerge the IntelliBrite Controller.

• Do not connect two or more IntelliBrite Controller together.

iii

IntelliBrite Controller Installation and User’s Guide

IntelliBrite®Controller kit contents

The following items are included in the IntelliBrite Controller kit:

• IntelliBrite Controller, P/N 600054

• Gasket, P/N 619763

• Knob, P/N 690026

• Door, P/N 690027

• Screw kit, P/N 619764

• Installation and User’s Guide (this manual)

Note: Outlet box purchased separately (see page 3)

Technical Support

Sanford, North Carolina (8 AM - 8:00 PM ET)

Moorpark, California (8 AM - 5:00 PM PT)

Phone: (800) 831-7133 - Fax: (800) 284-4151

www.pentair.com

Related manuals - Download the IntelliBrite LED Pool Light Installation and User’s

Guide (P/N 619675)

Contents

IntelliBriteController Overview...........................................................................1

Controls and Buttons .....................................................................................1

Selecting a Light Show or Fixed Color...............................................................2

Hold and Recall Feature....................................................................................2

Powering on the IntelliBrite light(s).....................................................................3

Troubleshooting .................................................................................................3

Outlet Box Speciﬁcations...................................................................................3

Installing an Outlet box for the IntelliBrite Controller ........................................4

Wiring an IntelliBrite Controller to IntelliBrite LED Lights...................................5

Maximum wattage when using multiple lights with controller.............................5

12 VAC IntelliBrite LED Landscape Lights .......................................................5

IntelliBrite Controller System Wiring Diagram....................................................6

Installing the IntelliBrite Controller in the Outlet box..........................................7

Wiring IntelliBrite Landscape LED Lights...........................................................8

Using the IntelliBrite Controller to control IntelliBrite

landscape LED lights.........................................................................................8

Maximum wattage when using multiple IntelliBrite LED lights

with the IntelliBrite Controller.............................................................................8

Wiring the IntelliBrite Controller to a 12 VAC Transformer..................................8

Troubleshooting for the IntelliBrite Controller.....................................................9

IntelliBrite Controller Installation and User’s Guide

IntelliBrite® Controller Overview

The IntelliBrite®Controller provides complete control of Pentair Aquatic

SystemsIntelliBrite underwater LED (light-emitting diode) lights, and IntelliBrite

LED landscape lights.It’s easy to select a lighting feature, just dial in any

one of the pre-programmed color light shows or ﬁxed colors.Using the Hold

and Recall buttons you can also create endless unique lighting effects.The

IntelliBrite Controller can control individual or multiple IntelliBrite LED lights.

Multiple IntelliBrite LED lights can be connected via a junction box to an

IntelliBrite Controller so that all lights can be switched on and off together.

IntelliBrite LED lights are fully compatible with Pentair IntelliTouch®and

EasyTouch®Control Systems.For more information about using IntelliBrite

lights with IntelliTouch systems, refer to the IntelliTouch User’s Guide (P/N

520102) and the EasyTouch User’s Guide (P/N 520584).

Controls and Buttons

The IntelliBrite Controller controls, buttons and LEDs are shown below:

PRINTED ON: 7/29/2009, 600054_ctlg pics.SLDASM

Power

ON/OFF Switch

RECALL button

and LED

Dial

(for selecting color

light shows and

ﬁxed colors)

Color show

Selections

Door

HOLD

button

and

LED

IntelliBrite Controller

The IntelliBrite controller is a 120 VAC device, DO NOT connect

12 VAC IntellilBrite pool/spa LED lights or IntelliBrite LED

landscape lights directly to the IntelliBrite controller, use an appropriate step

down transformer between the controller and lights.For more information see

page 5 - 9.

IntelliBrite Controller Installation and User’s Guide

Selecting a Light Show or Fixed Color

Note: When the IntelliBrite LED light(s) are powered on, a white light will

momentarily illuminate, followed by the selected color, unless the HOLD or

RECALL feature was previously enabled.

To select a color light show mode or ﬁxed color mode, rotate the dial so that it

points to the desired selection.

The color mode selections are described below starting clockwise from the

9 o’clock position:

Light Show Mode

• SAm Mode: Cycles through white, magenta, blue and green colors

(emulates the Pentair Water Pool and Spa SAm®light).

• Party Mode: Rapid color changing building energy and excitement.

• Romance Mode: Slow color transitions creating a mesmerizing and

calming effect.

• Caribbean Mode: Transitions between a variety of blues and greens.

• American Mode: Patriotic red, white and blue transition.

• California Sunset Mode: Dramatic transitions of orange, red and

magenta tones.

• Royal Mode: Richer, deeper color tones.

Fixed Colors

• Blue: Fixed color.

• Green: Fixed color.

• Red: Fixed color.

• White: Fixed color.

• Magenta: Fixed color.

Hold and Recall Feature

Note: When the IntelliBrite LED light(s) are powered on, a white light will

momentarily illuminate, followed by the selected color, unless the HOLD or

RECALL feature was previously enabled.

Hold button/LED: Press this button (LED on) to capture and save a color

effect while displaying one of the light show modes.When the button is

pressed, the LED will be on, indicating that the color effect is captured.

Recall Button/LED: Use this button (LED on) to activate the last saved

color effect.When the button is pressed, the LED will be on, indicating that

the color effect is being displayed.

IntelliBrite Controller Installation and User’s Guide

Powering on the IntelliBrite light(s)

When the IntelliBrite LED light is powered on, a momentarily white light

will illuminate, followed by the dial selected color.

Troubleshooting (see page 9 for more troubleshooting tips)

Use the following tips to help to resolve problems that might occur while

operating the IntelliBrite Controller.

PROBLEM/

FAULT SOLUTION

Both of the

LEDs are

ﬂashing.

The IntelliBrite Controller has detected that the load has

exceeded the maximum allowable wattage or the output is

shorted out

1. Switch of the IntelliBrite Controller OFF. Remove exces-

sive load or short.

2. Press the IntelliBrite Controller power switch to power on

the unit. Ensure that the LEDs are no longer ﬂashing.

The light will

not illumi-

nate.

Light does

not function

properly.

Check the ground fault wiring and reset if necessary.

Check the light wiring connection to the junction box at the

pool side and to the main circuit breaker.

Be sure that there is proper AC power applied to the light.

Outlet Box Speciﬁcations

(purchased separately)

The IntelliBrite Controller requires a

standard outlet box which is purchased

separately. The outlet box must meet the

following speciﬁcations:

• Outlet box type: 22.5 cubic

inches (minimum) - Suitable

for wet locations with UL/

CSA approval listings. Check

the inside of outlet box for

speciﬁcation label.

• A minimum of one 3/4” steel

conduit.

Outlet Box (22.5 cubic inches minimum)

1.60”

4.50”

2.75”

IntelliBrite Controller Installation and User’s Guide

Installing an Outlet box for the IntelliBrite®Controller

The IntelliBrite®Controller mounts onto a standard outlet box (22.5 cubic

inches). See page 3 for outlet box speciﬁcations.

To install the outlet box:

1. Position the IntelliBrite Controller and outlet box to meet National

Electrical Code requirements, and to prevent hazard to personnel.

2. Run conduit from the IntelliBrite light niche to the junction box.

Note: The outlet box must be located a minimum distance of ﬁve (5)

feet measured horizontally from the inside wall of the pool and not

less than one (1) foot above the maximum pool water level

measured to the top of the outlet box.

3. Remove the lower conduit plug from the outlet box.

4. Mount the outlet box onto the conduit.

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION

TURN power OFF at circuit breaker - Always

disconnect power to the pool light at the circuit

breaker before servicing the light. Failure to do

so could result in death or serious injury to

installer, service person, pool users, or others due

to electrical shock.

Outlet Box Lower

conduit

plug

IntelliBrite Controller Installation and User’s Guide

Wiring an IntelliBrite Controller to IntelliBrite LED

Lights

Maximum wattage when using multiple lights with controller

When using multiple IntelliBrite LED lights, the total allowable light wattage is

300 Watts maximum.The following example combination of IntelliBrite LED

lights can be connected to the IntelliBrite Controller:

• Three (3) IntelliBrite LED pool lights (each light 35 Watt maximum)

• Two (2) IntelliBrite LED spa light (18 Watt maximum)

• Eight (8) Landscape LED lights (each light 15 Watt maximum)

To wire multiple 120 Volt IntelliBrite LED Lights to an IntelliBrite Controller:

1. Route the IntelliBrite LED Light cord and the three wires (white,

green and black) from the GFCI, up through the conduit opening,

and into the outlet box.

2. Strip the ends of the three light conductors, and the three GFCI wires.

Note: Use underwater lights with water resistant cord only.

3. Using the ground screw in the outlet box, secure the green ground

wire from the light, and the GFCI to the back of the outlet box.

4. Connect the red wire from the Controller, to the red wire, which is at-

tached to the black wire of the light at the junction box.

5. Connect the white wire from the Controller to the white wire from the

light cord, and the white wire from the GFCI (neutral).

6. After the wiring has been completed and checked, proceed to

“Installing the Controller in the Outlet Box” on page 10.

12VAC IntelliBrite LED and Landscape Lights

IMPORTANT! When installing 12 VAC IntelliBrite LED and Landscape

lights, connect the lights to the secondary 12VAC output of the step down

transformer, then connect the IntelliBrite controller to the 120VAC primary

input of the step down transformer.

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION

TURN power OFF at circuit breaker - Always

disconnect power to the pool light at the circuit

breaker before servicing the light. Failure to do

so could result in death or serious injury to

installer, service person, pool users, or others due

to electrical shock.

Altri manuali per IntelliBrite

Indice

Lingue:

Altri manuali Pentair Controllori

Pentair

Pentair LINCOLN SYSTEM SENTRY 84530 Manuale del proprietario

Pentair

Pentair FLECK SXT Manuale utente

Pentair

Pentair Pentek Intellidrive Manuale utente

Pentair

Pentair Onga WaterSwitch WS1500200 Manuale utente

Pentair

Pentair intellidrive pid10 Manuale utente

Pentair

Pentair SPEEDEO CONNECT Manuale utente

Pentair

Pentair COLOR SYNC Manuale utente

Pentair

Pentair AK110 Manuale utente

Pentair

Pentair AUTOTROL 460TC Manuale utente

Pentair

Pentair raychem ngc-30/uit2 Istruzioni operative

Pentair

Pentair AQUATIC ECO-SYSTEMS SAFEGUARD UV SYSTEMS... Manuale utente

Pentair

Pentair Fleck 5800 LXT Manuale utente

Pentair

Pentair LINCOLN SYSTEM SENTRY 84530 Manuale del proprietario

Pentair

Pentair intellichem Manuale utente

Pentair

Pentair F783E Manuale utente

Pentair

Pentair FLECKXT Manuale utente

Pentair

Pentair Water Chemistry Controller Smart pH Manuale utente

Pentair

Pentair IntelliBrite Manuale utente

Pentair

Pentair RAYCHEM RAYSTAT-ECO-10 Manuale utente

Pentair

Pentair INTELLICHEM Series Manuale utente

Pentair

Pentair 962 Series Manuale utente

Pentair

Pentair Biffi ICON 2000 Manuale elenco delle parti

Pentair

Pentair ControlPro Series Manuale utente

Pentair

Pentair Intellichem 521498 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente