Phanteks NV7 Manuale utente
VERSION 1.0
USER MANUAL
4 5
TABLE OF CONTENTS
1. INTRODUCTION
3. SUPPORT
INTRODUCTION
INTRODUCING THE PHANTEKS NV7
The Phanteks NV7 is a showcase full-tower chassis with a clean look from every side. It is the rst
installment of the new NV series, which is focused on showcasing your hardware in a premium
build-quality chassis. Performance is uncompromised with Ultra-Fine Mesh panels while providing
a clean and stylish look with the nearly seamless tempered glass front and left side panels.
THE PHANTEKS TEAM
Introduction 5
D-RGB Lighting Effects 6
Exploded View 7
Accessories 8
Specications 9
2. BUILD YOUR SETUP
Remove External Panels 10
Remove Covers 12
Motherboard Installation 13
Power Supply Installation 14
Fan & Radiator Positions 15
Fan & Radiator Installation 16
Airow Congurations 20
Power Button & LED 21
Front I/O 22
Move Front I/O To Secondary Position 23
D-RGB Cables 24
Installing Storage 25
Internal Cable Management 27
Installing LED Covers 28
Installing GPU Support Bracket 30
External Cable Management 31
Contact Us 32
Warranty 33
6 7
LIGHTING EFFECTS
The Digital-RGB lighting can be easily
controlled with the 4 buttons on top of
the chassis:
EXPLODED VIEW
PARTS
1Chassis
2Front glass panel
3Right side mesh panel
4Left glass panel
5Top panel
6Bottom fan bracket
7Side fan bracket
8Rear door
9Bottom dust lter
10 Front I/O
11 GPU Support Bracket
12 Motherboard Cover
13 D-RGB Cover
14 Top I/O
15 Rear Mesh Cover
16 Airow Cover
15
04
01
16
13
12
11
08
10
09
06
05
03
07
14
MODES
Solid
Rainbow
Breathing
Pixelate
Wave
Two-Tone
Fade
BLUEYELLOW TEALORANGEMAGENTA LIGHT
BLUE
GOLDPINK GREENREDWHITE
Press and hold the MODE button for two seconds to turn off LEDs,
press again to turn it ON
TURN OFF LEDs
SPEED
COLOR
MODE
CHANNEL SWITCH A/B
02
8 9
ACCESSORIES
GPU SUPPORT BRACKET
Included in accessory box
SCREWS OTHER ACCESSORIES
1x D-RGB Motherboard adapter cable
1x Microber Cloth
6x Zipties
1x Manual
AIRFLOW COVER
2x Included in accessory box
SPECIFICATIONS
CASE SPECIFICATIONS
Dimension (DxWxH) 532 x 253 x 586 mm / 20.9 x 10.0 x 23.1 in
Form Factor Full Tower
Materials Steel, Tempered Glass front and side panels
Motherboard Support ATX, micro-ATX, mini-ITX, E-ATX (up to 277 mm
wide), SSI-CEB (up to 290 mm w/o cover )
Front I/O
Power switch, 1x USB 3.2 Gen2 Type-C, 2x USB 3.0,
D-RGB Mode, D-RGB Color, D-RGB Speed, D-RGB
Channel, Microphone/Headphone
PCI SLOTS & DRIVE BAYS
PCI Slots 8x
Internal 2.5” 6x
Internal 3.5” 2x
FAN 120mm 140mm
Side 4x -
Top 3x -
Bottom 3x 3x
Rear 2x -
RADIATOR 120mm 140mm
Side up to 360 -
Top up to 360 -
Bottom up to 360 up to 280
Rear up to 240 -
INCLUDED ACCESSORIES
GPU Support Bracket 1x
Airow Cover 2x
Toolbox 1x
CLEARANCE
GPU Length 450 mm / 17.7 in
CPU Cooler Height 185 mm / 7.3 in
PSU Length 255 mm / 10.0 in
Side 360 Radiator Maximum size: 132 x 440 mm
Side 360 Radiator Thickness 65 mm (to GPU)
Top 360 Radiator Maximum size: 132 x 440 mm
Rear 240 Radiator Maximum size: 132 x 320 mm
SSD + MOTHERBOARD
SCREW
34X
ANTI-SAG BRACKET
THUMB SCREW
4X
EXTRA RIGHT SIDE
PANEL SCREW
1X
STAND-OFF REMOVAL
TOOL
1X
MOTHERBOARD
STAND-OFF
1X
PSU SCREW
34X
HDD LOCKING SCREW
9X
10 11
REMOVE EXTERNAL PANELS
Open the rear door by pulling it from the
bottom right corner.
Loosen the 2 thumb screws in the rear,
slide the glass side panel to the rear and
tilt it sideways to remove it.
Unscrew the 2 screws from the left side
and slide the panel to the left to remove
it. Optionally, this panel can be left on
during installation.
OPEN REAR PANEL REMOVE GLASS SIDE PANEL REMOVE GLASS FRONT PANEL
01 02 03
REMOVE EXTERNAL PANELS
Loosen the 2 thumb screws of the top
panel in the rear. Slide the top panel to
the rear to remove it.
Remove the screw on the top and slide
the right panel upwards to remove it.
Optionally, remove the back door by
sliding it upwards when it is in open
position.
REMOVE TOP PANEL REMOVE RIGHT SIDE PANEL REMOVE REAR DOOR
04 05 06
1.
2.
1.
1.
1.
2.
1. 1.
2.
1.
2.
1.
2.
THUMB SCREW 2x
LOOSEN
THUMB SCREW 2x
LOOSEN
SCREW 1x
REMOVE
SCREW 2x
REMOVE
3. 2.
12 13
REMOVE COVERS
Slide the D-RGB cover to the front of the chassis to remove it. Remove the screw located on the right side of the chassis. Push
the motherboard cover down to remove it.
REMOVE D-RGB COVER
01 02
MOTHERBOARD INSTALLATION
Align the motherboard with the
screwholes on the chassis’ motherboard
tray.
Secure the motherboard with 9x
motherboard screws.
REMOVE MOTHERBOARD COVER ALIGN MOTHERBOARD
SECURE MOTHERBOARD
01
02
For Micro-ATX and SSI-CEB check
the motherboard instructions for
stand-off locations.
ATTENTION
1. unscrew
1.
2.
3.
MB SCREWS 9x
INSTALL
Use the included stand-off tool to
easily remove and re-install the
motherboard stand-offs for other
motherboard form-factors
PRO TIP
SCREW 1x
REMOVE
14 15
POWER SUPPLY INSTALLATION
01 INSERT PSU
Insert the PSU from the right side of the chassis.
02 SECURE PSU
Secure the PSU from the rear with 4x PSU
screws.
Attach all PSU cables rst before
installing the PSU into the chassis.
PRO TIP PSU SCREW 4x
INSTALL
RADIATOR & FAN POSITIONS
RADIATOR POSITIONS FAN POSITIONS
up to 360
up to 360
up to 280
up to 240
up to 360
120
120
120
120
120
120
120
120
120
120
120
120
140140140
Side: up to 360 Top: up to 360
Bottom: up to 360/280 Rear: up to 240
Side: 4x 120 mm Top: 3x 120 mm
Bottom: 3x 120/140 mm Rear: 2x 120 mm
16 17
FAN & RADIATOR INSTALLATION
Remove the bracket by pulling the
handle at the top of the bracket and take
it out.
Remove the screw located on the top.
Install up to 4x 120 fans/360 radiator on
the bracket.
Re-install the bracket and secure it with
the screw located on the top.
Use the 3 cut-outs to route all fan cables.
SIDE FAN/RADIATOR BRACKET
02 PULL & TAKE OUT BRACKET
01 REMOVE SCREW
03 INSTALL FANS/RADIATOR
04 INSTALL SIDE BRACKET
A.
B.
routing cut-outs
C.
2.
Use the provided airow cover for
optimal airow. When used, the
airow will be closed off.
PRO TIP
1.
3.
THUMB SCREW 1x
REMOVE
1 2
3
RECOMMENDED AIRFLOW CONFIGURATIONS
AIR-COOLED CONFIGURATION WATER COOLED CONFIGURATION
Side: Intake Top: Exhaust
Bottom: Intake Rear: Exhaust
Side: Exhaust Top: Exhaust
Bottom: Intake Rear: Exhaust
up to 360
18 19
FAN & RADIATOR INSTALLATION
If no radiator is installed, re-install the
rear mesh panel.
Fan cables can be routed through the
cut-outs on the rear.
Install up to 2x 120 fans on the inside
of the rear chassis. A 240 radiator can
be installed on the outside of the rear
chassis.
Remove the screw on the rear and
remove the mesh panel.
The rear has space for up to 240 radiator
and 2x 120 fans. The fans can be installed
in front of the rear panel while the
radiator can be installed behind the rear
panel.
REAR FAN/RADIATOR POSITION
03 RE-INSTALL REAR MESH PANEL
02
01
INSTALL FANS/RADIATOR
REMOVE REAR MESH PANEL
1.
fans
2.
2.radiator
SCREW 1x
REMOVE
routing cut-out
FAN & RADIATOR INSTALLATION
Install up to 3x 120mm / 3x 140 mm
fans and/or 280/360 radiator on to the
bracket.
Release the bracket by removing the
rear thumb screw. Slide the bracket to
the front to remove it.
Re-install the bracket by sliding it
towards the rear and secure it with the
thumb screw.
It is possible to install the bracket the
other way around for angled fans.
Fan cables can be routed through the
cut-outs on the rear and side.
Rotated bracket for angled fan positioningDefault bracket position for straight fans
BOTTOM FAN/RADIATOR BRACKET
02 INSTALL FANS/RADIATOR
01 REMOVE BOTTOM BRACKET
03 RE-INSTALL BOTTOM BRACKET
23
Rotate
180 degrees
for angled fans
1.
routing cut-outs
THUMB SCREW 1x
REMOVE
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Phanteks Accessori per computer
