PheeNet WLn-402 Manuale utente
Quick Installation Guide WLn-402
Version 1.0
IEEE802.11n
Wireless Router
Package Contents .......................................................................... Page 1
Build Network Connections ......................................................... Page 2
Network Setup ............................................................................... Page 3
Package Contents
Before you starting to use this router, please check if there’s anything missing in the package,
and contact your dealer of purchase to claim for missing items:
□WLn-402, 802.11n Wireless Router ( 1 pcs)
□Quick installation guide (1 pcs)
□User manual CD-ROM (1 pcs)
□A/C power adapter (1 pcs)
Build Network Connections
Please follow the following instructions to setup wireless router:
1. Connect your xDSL / cable modem to the WAN port of router by Ethernet cable.
2. Connect all your computers, network devices (network-enabled consumer devices other than
computers, like game console, or switch / hub) to the LAN port of the router.
3. Connect the A/C power adapter to the wall socket, and then connect it to the ‘Power’socket
of the router.
Please check all LEDs on the front panel. ‘PWR’LED should be steadily on, WAN and LAN
LEDs should be on if the computer / network device connected to the respective port of the
router is powered on and correctly connected.
If ‘PWR’LED is still off and you’re sure that all cable connections are connected properly,
please contact your dealer of purchase for assistance.
Network Setup
Please use the web browser to configure the wireless router.Acomputer with wired
Ethernet connection to the wireless router is requiredfor this first-time configuration.
1. Set your computer to obtain an IP
address from wireless router: click
‘Start’button(it should be located at
lower-left corner of your computer),
then click control panel. Double-click
Network Connections, then
double-click Local Area Connection.
Click ‘Properties’.
2. Local Area Connection
Properties window will appear. Select
Internet Protocol (TCP/IP)
, then click
‘Properties’.
3.Select ‘Obtain an IP address
automatically’ and ‘Obtain DNS server
address automatically’, then click
‘OK’.
4. After the IP address setup is
complete, please click ‘start’ -> ‘run’ at
the bottom-lower corner of your
desktop, then input ‘cmd’ and click
‘OK’.
5. Input ‘ipconfig’, then press
‘Enter’ key. Please check the
IP address followed by
‘Default Gateway’ (In this
example, the IP address of
router is 192.168.2.1)
Please note that this value
may be different.
6. Start the web browser and input the
IP address of wireless router in
address bar, and the following
message should be shown. Please
input user name and password, then
click ‘OK’ to access web management
interface of wireless router.
Default user name: admin
Default password: 1234
7. Click ‘QuickSetup’
8. Select time
zone of the area
where you live,
then click ‘Next’.
HERE!
HERE!
9. Select a broadband type of the
Internet connection you’re using, then
click ‘Next’.
10. Please input the Internet
connection parameters, you should
use the value provided by your
Internet service provider.
Click ‘OK’when you finish.
(The content of this page will vary
depends on the connection method
you selected in step 9)
11. Click ‘Apply’.
12.When you see this message, the
router will be ready with new settings
within 30 seconds.
13. Please use your computer to connect to any website on Internet, or start any
Internet application and see if they’re working properly.
For instructions of advanced settings and wireless network setup, please refer to user
manual in supplied CD-ROM.
Indice
Altri manuali PheeNet Router di rete
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza