Philips VSS7902/00T Manuale utente

Electro Magnetic Compatibility (EMC)

This equipment complies with European rules for EMC according to

EN55013, EN55020 and EN50082-1.

Operation is subject to the following two conditions:

1 This device may not cause harmful interference.

2 This device must accept any interference received, including interference

that may cause undesired operation.

The equipment conforms with the EMC directive and low-voltage

directive.

This device complies to FCC rules under test conditions that included

use of system cables and connectors between system components. If you

have any problems, contact your dealer.

Warnings

Any unauthorized modification to this equipment may cause violation of

the FCC rules resulting in the revocation of the authorization to operate

the equipment.

To prevent fire or shock hazard, do not expose this accessory to rain or

moisture.

The exclamation mark within a triangle is intended to alert the

user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the

appliance.

Alarm/Action Box

Table of contents

Page

Introduction .................................................................................................................4

Installation....................................................................................................................6

Mounting the box

Installation and setting of an optional

Passive Infra-Red (PIR) detector

Location of the PIR

Installation of the PIR

PIR settings

Walk test LED

Pulse counter

System cable

Action output

Alarm input

Settings..........................................................................................................................13

Designating the box (CAMERA # switch)

Box number

Tamper switch active

Last in line switch

Double addressing error

English

Read these instructions, before putting your system in operation

English

Introduction

Thank you for buying this accessory for your observation system.

1 System monitor

2 Video recorder (VCR)

3 Slave monitor

4 Accessory boxes (0-2 per cable)

5 Interface box

6 System cameras

7 Non system cameras (CVBS)

8 Mains power adapter

The following items are included in this kit:

1 Alarm/action box

1 System cable (5m/15ft)

1 User manual

1 PIR unit (for version with PIR)

1 Cable (50 cm) for interconnection between alarm/action box and

PIR (for version with PIR)

Colour Observation Monitor

CL 66610005_005b.AI

6 6 7

talk action

menu _+next

auto view

Colour Observation system

Colour Observation Monitor

4 4

N.O. = Normally Open

N.C. = Normally Closed

The alarm/action box performs two distinct functions:

1 Action

This function, for example, opens a door remotely.

Pressing the action button of the system monitor activates a relay contact.

This contact (N.O., N.C.) can activate, for instance, a door opener.

Note that the action button only activates the action box designated to

the camera input whose picture is shown on the monitor screen.

2 Alarm

This function provides alarm inputs to the security system. All kinds of

detectors having a N.O. or N.C. contact are supported, for example:

•infrared detectors

•smoke detectors

•magnetic door/window contacts

When a detector triggers the alarm/action box, the system monitor

automatically switches to the camera input the alarm/action box is

designated to. The system monitor produces an alarm and activates its

alarm contact.

There are two versions of the alarm/action box: one with a Passive

InfraRed (PIR) motion detector and one without. The description in this

manual applies to both versions.

If the automatic camera sequence is active, it stops at the camera input in

question.

CL 66610005_511.AI

N.O.

N.C.

common

Installation

Remark: When the system configuration is altered, the system monitor needs to check

and memorize the configuration of the cameras and accessories connected to its inputs.

This is done automatically when the power is switched on. Use the power switch to

switch off. Operating the power save key is not sufficient.

If switching off is impracticable, use the auto install option of the system monitor's

install menu.

Mounting the box

1 Loosen the screw holding the cover and remove the cover.

2 Remove the circuit board 1.

3 Fasten the bottom plate of the box with two screws.

CL 66610005_501.AI

CL 66610005_502.AI

CL 66610005_504.AI

4 Fit the circuit board.

5 Now make the connections as described in section 'Action output'.

Remark: See section 'Installation and setting of an optional Passive

Infra-Red (PIR) detector', for installation and connection of an PIR-detector.

6IMPORTANT: Adjust the settings of the circuit board switches to

configure the box according to your system. See section 'settings'.

7 Fit the cover and secure the screw holding it.

Installation and setting of an optional Passive Infra-Red

(PIR) detector

Location of the PIR

The position of the PIR determines its view.

Select a location where an eventual burglar is most likely to be detected.

Place the sensor at a height of ± 2.2 m to accomplish the largest field of

view (see figure below).

Sensor range (lens position 0°)

Side view Top view

Be aware of the following before mounting the PIR:

•Avoid a location of the PIR near to radiators, heating/cooling ducts or

air conditioners.

•Do not point the sensor's field of view to windows subject to direct

sunlight or drafts.

•Do not block the sensor's field of view by placing large objects in its line

of sight (e.g. curtains, potted plants, furniture).

4M

13.15Ft 8M

26.3Ft 14M

46Ft

2.2M

7.2Ft

110

CL 76610006_001.AI

Installation of the PIR

1 Remove the fixation-screw (1) and open the housing by releasing the

locking latch (2). Both are located at the bottom of the unit.

2 Remove the circuit board by loosening the fixation-screw (1).

Warning: Never touch the face of the PYRO sensor (refer to lay out drawing

next page).

3 Knock out the desired mounting holes (1) and wiring holes (2) in the

bottom plate.

4 Thread the wires through the knocked out wiring hole(s).

5 Fasten the bottom plate with two screws, using the mounting holes.

6 Fit the circuit board.

CL 76610006_002.AI

CL 76610006_003.AI

1 2

Adjust lens position (0°, -5° or -10°) according to desired maximum

sensor range (see table below).

Remark: Do not use positions +5° or +10° as they do not apply to this PIR.

Sensor height Maximum sensor range (m) / Lens position (°)

0° -5° -10°

2.5 m 14 m 12.5 m 11 m

2.0 m 12 m 10.5 m 9.5 m

1.5 m 10 m 8.5 m 8 m

7 Make the interconnections between the PIR and the alarm/action box

with the cable supplied (see figure below).

1 Terminal block (for interconnection with alarm/action box)

2 Lens position (sensor range adjustment)

3 Jumper (walk test LED activated/deactivated)

4 Tamper switch

5 PYRO sensor

6 Jumper (1, 2 or 3 pulse count)

7 Locking latch

8 Terminal block in alarm/action box

CL 76610006_004.AI

5 87 6

2 14 3

GND

+12V

+10

-5

-10

+_NC

PIR

8 Adjust settings of walk test LED and/or pulse counter, if required.

See section 'PIR settings'.

9 Fit the front cover. Check if it is locked to the bottom side.

10 Fasten the fixation-screw.

Remark: The PIR detector will start detecting movement approximately 2 minutes

after mains power-on.

PIR settings

There are 2 jumpers to set the PIR to your own requirements:

•Walk test LED

•Pulse counter (1, 2 or 3)

See previous figure for the location of the jumpers.

Walk test LED

•jumper installed:

Walk test LED is activated. When the PIR sensor is triggered, the LED

will light.

•jumper not installed:

Walk test LED is deactivated.

Pulse counter

Set this jumper to select the number of times the sensor must be triggered

(1, 2 or 3 times) before an alarm is generated.

The following jumper settings are possible:

Remark: The PIR detector is equiped with a 'detection window'. In case of an

alarm, 15 seconds after the last movement has been detected, a new alarm can be

generated.

CL 76610006_005.AI

2X 3X1X

System cable

For the interconnections between the monitor, accessories and camera a

system cable is supplied. For optimum picture and sound quality you

should always use 4-wire dual twisted-pair cable when extending the

connection (max. 300m/900ft). The cable and plugs are available in the

hobby and professional trade. Pay attention that the connectors are fixed

to the cable corresponding to the figure below.

If the cable length between monitor and camera exeeds 200m/600ft after

an accessory is inserted in the line a mains power adapter should be used

to power the camera (see accessories).

Caution: The plugs used for the observation system have the same dimensions as

standard telephone plugs.

Never connect the security system with telephone equipment!

The two sockets for the system cable are interchangeable. One socket

connects the box to the system component previous in the cable, the

other to the next (if any).

CL 66610005_006.AI

4-5

2-3

4-5

2-3

Indice

Altri manuali Philips Accessori

Philips

Philips CRP381 Manuale utente

Philips

Philips STO2520 Manuale utente

Philips

Philips SH91/51 Manuale utente

Philips

Philips CRP303 Manuale utente

Philips

Philips CRP324 Manuale utente

Philips

Philips HF3462/10 Manuale utente

Philips

Philips SDW5002O Manuale utente

Philips

Philips SDW5061O Manuale utente

Philips

Philips SVC2550W/27 Manuale utente

Philips

Philips HP5241 Manuale utente

Philips

Philips HF3650 Manuale utente

Philips

Philips HF3550/60 Manuale utente

Philips

Philips CRP393 Manuale utente

Philips

Philips HP3641 Manuale utente

Philips

Philips HF3485/60 Manuale utente

Philips

Philips WelcomeBell 300 AddPush Manuale utente

Philips

Philips HF3510/01 Manuale utente

Philips

Philips SAC3540W Manuale utente

Philips

Philips LRI8135/00 Manuale utente

Philips

Philips SAC2520W/10 Manuale utente

Philips

Philips EasySense SNH210 MC Manuale utente

Philips

Philips DLA81818H Manuale utente

Philips

Philips KMZ51 Istruzioni per l'installazione e il funzionamento

Philips

Philips SH90/81 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente