Philips TDA2613 Manuale utente

DATA SHEET

Product speciﬁcation

File under Integrated circuits, IC01 July 1994

INTEGRATED CIRCUITS

TDA2613

6 W hi-fi audio power amplifier

July 1994 2

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

GENERAL DESCRIPTION

The TDA2613 is a hi-fi audio power amplifier encapsulated in a 9-lead SIL plastic power package. The device is

especially designed for mains fed applications (e.g. tv and radio).

Features

•Requires very few external components

•Input muted during power-on and off

(no switch-on or switch-off clicks)

•Low offset voltage between output and ground

•Hi-fi according to IEC 268 and DIN 45500

•Short-circuit-proof

•Thermally protected.

QUICK REFERENCE DATA

PACKAGE OUTLINE

TDA2613: 9-lead SIL; plastic power (SOT110B); SOT110-1; 1996 August 07.

Supply voltage range VP15 to 42 V

Output power at THD = 0,5%,

VP= 24 V Potyp. 6 W

Voltage gain Gvtyp. 30 dB

Supply voltage ripple rejection SVRR typ. 60 dB

Noise output voltage Vno(rms) typ. 70 µV

July 1994 3

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

PINNING

1. n.c. not connected 5. GND ground (asymmetrical) or

2. n.c. not connected negative supply (symmetrical)

3. VP/2 1⁄2VP(asymmetrical) or 6. OUT output

ground (symmetrical) 7. +VPpositive supply

4. n.c. not connected 8. INV inverting input

9. −INV non-inverting input

Fig.1 Block diagram.

July 1994 4

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

FUNCTIONAL DESCRIPTION

This hi-fi power amplifier is designed for mains fed applications. The device is intended for asymmetrical power supplies,

but a symmetrical supply may also be used. An output power of 6 watts (THD = 0,5%) can be delivered into an 8 Ωload

with an asymmetrical power supply of 24 V.

The gain is fixed internally at 30 dB. Internal gain fixing gives low gain spread.

A special feature of this device is a mute circuit which suppresses unwanted input signals during switching on and off.

Referring to Fig.4, the 100 µF capacitor creates a time delay when the voltage at pin 3 is lower than an internally fixed

reference voltage. During the delay the amplifier remains in the DC operating mode but is isolated from the non-inverting

input on pin 9.

Two thermal protection circuits are provided, one monitors the average junction temperature and the other the

instantaneous temperature of the power transistors. Both protection circuits activate at 150 °C allowing safe operation to

a maximum junction temperature of 150 °C without added distortion.

RATINGS

Limiting values in accordance with the Absolute Maximum System (IEC 134)

Note to the Ratings

For asymmetrical power supplies (at short-circuiting of the load) the maximum supply voltage is limited to VP= 28 V.

If the total internal resistance of the supply (RS)≥4Ω, the maximum unloaded supply voltage is increased to 32 V.

For symmetrical power supplies the circuit is short-circuit proof to VP= ±21 V.

PARAMETER CONDITIONS SYMBOL MIN. MAX. UNIT

Supply voltage VP−42 V

Non-repetitive peak

output current IOSM −4A

Total power dissipation see Fig.2 Ptot

Storage temperature range Tstg −55 +150 °C

Junction temperature Tj−150 °C

Short-circuit time: see note

outputs short-circuited

to ground

(full signal drive) tsc −1 hour

July 1994 5

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

THERMAL RESISTANCE

HEATSINK DESIGN EXAMPLE

With derating of 8 K/W, the value of heatsink thermal resistance is calculated as follows:

given RL= 8 Ωand VP= 24 V, the measured maximum dissipation is 4,1 W; then, for a maximum ambient temperature

of 60 °C, the required thermal resistance of the heatsink is:

Note: The metal tab (heatsink) has the same potential as pin 5 (GND).

From junction to case Rth j-c = 8 K/W

Fig.2 Power derating curve.

Rth h-a 150 60–

41,

---------------------- 814K/W≈–=

July 1994 6

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

CHARACTERISTICS

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Supply voltage range

operating mode VP15 24 42 V

input mute mode VP4−10 V

Repetitive peak

output current IORM 2.2 −−A

Operating mode: asymmetrical power supply; test circuit as per Fig.4;

VP= 24 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz

Total quiescent current Itot 10 20 35 mA

Output power THD = 0,5% Po56 −W

THD = 10% Po6,5 8,0 −W

Total harmonic

distortion Po= 4 W THD −0,15 0,2 %

Power bandwidth THD = 0,5%;

note 1 B −20 to 16 k −Hz

Voltage gain Gv29 30 31 dB

Noise output voltage

(r.m.s. value);

unweighted (20 Hz

to 20 kHz) RS= 2 kΩVno(rms) −70 140 µV

Input impedance |Zi|142026kΩ

Supply voltage

ripple rejection note 2 SVRR 35 44 −dB

Input bias current Iib −0,3 −µA

DC output offset with respect

voltage to VP/2 Vos −30 200 mV

Input mute mode: asymmetrical power supply; test circuit as per Fig.4;

VP= 8 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz

Total quiescent current Itot 515 20mA

Output voltage Vi= 600 mV Vout −2,0 2,8 mV

Noise output voltage

(r.m.s. value);

unweighted (20 Hz

to 20 kHz) RS= 2 kΩVno(rms) −70 140 µV

Supply voltage

ripple rejection note 2 SVRR 35 55 −dB

DC output offset with respect

voltage to VP/2 Vos −40 200 mV

July 1994 7

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

Notes to the characteristics

1. Power bandwidth at Po max −3 dB.

2. Ripple rejection at RS= 0 Ω, f = 100 Hz to 20 kHz;

ripple voltage = 200 mV (r.m.s. value) applied to positive or negative supply rail.

Operating mode: symmetrical power supply; test circuit as per Fig.3;

VP= ± 12 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz

Total quiescent current Itot 10 20 35 mA

Output power THD = 0,5% Po56 −W

THD = 10% Po6,5 8,5 −W

Total harmonic distortion Po= 4 W THD −0,13 0,2 %

Power bandwidth THD = 0,5%

note 1 B −40 to 16 k −Hz

Voltage gain Gv29 30 31 dB

Noise output voltage

(r.m.s. value);

unweighted (20 Hz to

20 kHz) RS= 2 kΩVno(rms) −70 140 µV

Input impedance |Zi|142026kΩ

Supply voltage

ripple rejection SVRR 40 60 −dB

DC output offset with respect

voltage to ground Vos −30 200 mV

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

July 1994 8

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

APPLICATION INFORMATION

Fig.3 Test and application circuit; symmetrical power supply.

Fig.4 Test and application circuit; asymmetrical power supply.

July 1994 9

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

Input mute circuit

The input mute circuit operates only during switching on and off of the supply voltage. The circuit compares the 1⁄2supply

voltage (at pin 3) with an internally fixed reference voltage (Vref), derived directly from the supply voltage. When the

voltage at pin 3 is lower than Vref the non-inverting input (pin 9) is disconnected from the amplifier. The voltage at pin 3

is determined by an internal voltage divider and the external 100 µF capacitor.

During switching on, a time delay is created between the reference voltage and the voltage at pin 3, during which the

input terminal is disconnected, (as illustrated in Fig.5).

Fig.5 Input mute circuit; time delay.

July 1994 10

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

PACKAGE OUTLINE

UNIT AA

max.

2A3b1D1

bcD

(1) E(1) Z

max.

(1)

eLPP

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC EIAJ

mm 18.5

17.8 3.7 8.7

8.0

15.8

15.4 1.40

1.14 0.67

0.50 1.40

1.14 0.48

0.38 21.8

21.4 21.4

20.7 6.48

6.20 3.4

3.2

2.54 1.0

5.9

5.7

4.4

4.2

3.9

3.4 15.1

14.9

1.75

1.55

DIMENSIONS (mm are the original dimensions)

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

2.75

2.50

SOT110-1 92-11-17

95-02-25

0 5 10 mm

scale

0.25

q1q2

seating plane

pin 1 index

SIL9MPF: plastic single in-line medium power package with fin; 9 leads SOT110-1

Indice

Altri manuali Philips Amplificatore

Philips

Philips MC1458 Manuale del proprietario

Philips

Philips PM 3342 Manuale utente

Philips

Philips TDA8560Q Manuale utente

Philips

Philips BGY89 Manuale utente

Philips

Philips TDA2616 Manuale utente

Philips

Philips SA58605 Manuale utente

Philips

Philips FA761 Manuale utente

Philips

Philips FA951/00S Manuale utente

Philips

Philips TDA1576T Manuale utente

Philips

Philips TDA8946J Manuale utente

Philips

Philips TDA6103Q Manuale utente

Philips

Philips TDA6107JF Manuale utente

Philips

Philips FA 931 Manuale utente

Philips

Philips NE5512 Manuale del proprietario

Philips

Philips TFA9843AJ Manuale utente

Philips

Philips TDA8591J Manuale utente

Philips

Philips SA2411 Manuale utente

Philips

Philips TDA7050T Manuale utente

Philips

Philips CMP100/93 Manuale utente

Philips

Philips Amplifier Manuale utente

Philips

Philips TDA8922 Manuale utente

Philips

Philips CR6927 Manuale utente

Philips

Philips 22RH520 00 Manuale utente

Philips

Philips CMP200 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente