Philips UA733 Manuale utente
Philips Semiconductors Linear Products Product specification
µA733/733CDifferential video amplifier
262
April 15, 1992 853-1064 06456
DESCRIPTION
The 733 is a monolithic differential input, differential output,
wide-band video amplifier. It offers fixed gains of 10, 100, or 400
without external components, and adjustable gains from 10 to 400
by the use of an external resistor. No external frequency
compensation components are required for any gain option. Gain
stability, wide bandwidth, and low phase distortion are obtained
through use of the classic series-shunt feedback from the
emitter-follower outputs to the inputs of the second stage. The
emitter-follower outputs provide low output impedance, and enable
the device to drive capacitive loads. The 733 is intended for use as
a high-performance video and pulse amplifier in communications,
magnetic memories, display and video recorder systems.
FEATURES
•120MHz bandwidth
•250kΩinput resistance
•Selectable gains of 10, 100, and 400
•No frequency compensation required
•MIL-STD-883A, B, C available
PIN CONFIGURATION
1
2
3
4
5
6
7 8
14
13
12
11
10
9
INPUT 2
NC
V–
NC
OUTPUT 2
INPUT 1
NC
V+
NC
OUTPUT 1
TOP VIEW
N Package
G2B GAIN SELECT
G1B GAIN SELECT
G2A GAIN SELECT
G1A GAIN SELECT
APPLICATIONS
•Video amplifier
•Pulse amplifier in communications
•Magnetic memories
•Video recorder systems
ORDERING INFORMATION
DESCRIPTION TEMPERATURE ORDER CODE DWG #
14-Pin Plastic Dual In–Line Package (DIP) -55°C to +125°CµA733N 0405B
14-Pin Plastic Dual In–Line Package (DIP) 0 to +70°CµA733CN 0405B
CIRCUIT SCHEMATIC
+V
Q6
OUTPUT 1
OUTPUT 2
R1 R2 R8 R10 R9
Q5
Q4
Q3
R12
Q11
R14
Q9
G1A
INPUT 1 INPUT 2
R3 R5
Q1 Q2
-V
2.4kΩ2.4kΩ
G2A
GAIN
SELECT 50Ω
590Ω
50Ω
R4 590Ω
R6
Q7
R7
300Ω
G2B
G1B
10kΩ1.1kΩ1.1kΩ
R11
7kΩ
7kΩ
1.4kΩ
Q8 Q10
300ΩR12
400Ω400Ω
Philips Semiconductors Linear Products Product specification
µA733/733CDifferential video amplifier
April 15, 1992 263
ABSOLUTE MAXIMUM RATINGS
SYMBOL PARAMETER RATING UNIT
VDIFF Differential input voltage ±5 V
VCM Common-mode input voltage ±6 V
VCC Supply voltage ±8 V
IOUT Output current 10 mA
TJJunction temperature +150 °C
TSTG Storage temperature range -65 to +150 °C
TAOperating ambient temperature range
µA733C 0 to +70 °C
µA733 -55 to +125 °C
PDMAX Maximum power dissipation, 1420 mW
25°C ambient temperature (still-air)1
NOTE:
1. The following derating factors should be applied above 25°C:
N package at 11.4mW/°C
DC ELECTRICAL CHARACTERISTICS
TA=+25°C, VS=±6V, VCM=0, unless otherwisespecified. Recommended operating supply voltages VS=±6.0V.
SYMBOL
PARAMETER
TEST CONDITIONS
µA733C µA733
UNIT
SYMBOL
PARAMETER
TEST CONDITIONS
Min Typ Max Min Typ Max
UNIT
Differential voltage gain RI= 2kΩ, VOUT = 3VP-P
Gain 12250 400 600 300 400 500 V/V
Gain 2280 100 120 90 100 110 V/V
Gain 338 10 12 9 10 11 V/V
BW
Gain 1140 40
MHz
BW
Gain 2290 90
MHz
Gain 33120 120
tRVOUT = 1VP-P
Gain 1110.5 10.5 ns
Gain 224.5 12 4.5 10 ns
Gain 332.5 2.5 ns
tPD VOUT = 1VP-P
Gain 117.5 7.5 ns
Gain 226.0 10 6.0 10 ns
Gain 333.6 3.6 ns
RIN Gain 124.0 4.0 kΩ
Gain 2210 30 20 30 kΩ
Gain 33250 250 kΩ
Input capacitance2Gain 2 2.0 2.0 pF
IOS Input offset current 0.4 5.0 0.4 3.0 µA
IBIAS Input bias current 9.0 30 9.0 20 µA
VNOISE Input noise voltage BW=1kHz to 10MHz 12 12 µVRMS
VIN Input voltage range ±1.0 ±1.0 V
CMRR Gain 2 VCM=±1V, f≤100kHz 60 86 60 86 dB
Gain 2 VCM=±1V, f=5MHz 60 60 dB
Philips Semiconductors Linear Products Product specification
µA733/733CDifferential video amplifier
April 15, 1992 264
DC ELECTRICAL CHARACTERISTICS(Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
µA733C µA733
UNIT
SYMBOL
PARAMETER
TEST CONDITIONS
Min Typ Max Min Typ Max
UNIT
SVRR Supply voltage rejection ratio Gain 2 ∆VS= ±0.5V 50 70 50 70 dB
Output offset voltage RL= ∞
Gain 110.6 1.5 0.6 1.5 V
Gain 2 and 32, 30.35 1.5 0.35 1.0 V
VCM Output common-mode voltage RL= ∞2.4 2.9 3.4 2.4 2.9 3.4 V
Output voltage swing, differential RL=2kΩ3.0 4.0 3.0 4.0 VP-P
ISINK Output sink current 2.5 3.6 2.5 3.6 mA
ROUT Output resistance 20 20 Ω
ICC Power supply current RL= ∞18 24 18 24 mA
THE FOLLOWING SPECIFICATIONS APPLY OVER TEMPERATURE 0°C ≤TA≤70°C -55°C ≤TA≤125°C
Min Typ Max Min Typ Max UNIT
Differential voltage gain RI= 2kΩ, VOUT = 3VP-P
Gain 11250 600 200 600 V/V
Gain 2280 120 80 120 V/V
Gain38 12 8 12 V/V
RIN Input resistance
Gain 228 8 kΩ
IOS Input offset current 6 5 µA
IBIAS Input bias current 40 40 µA
VIN Input voltage range ±1.0 ±1.0 V
CMRR Common-mode rejection ratio
Gain 2 VCM=±V, F≤100kHz 50 50 dB
SVRR Supply voltage rejection ratio
Gain 2 ∆VS=±0.5V 50 50 dB
VOS Output offset voltage RL= ∞
Gain 111.5 1.5 V
Gain 2 and 32, 31.5 1.2 V
VDIFF Output voltage swing, differential RL= 2kΩ2.8 2.5 VP-P
ISINK Output sink current 2.5 2.2 mA
ICC Power supply current RL± ∞ 27 27 mA
NOTES:
1. Gain select pins G1A and G1B connected together.
2. Gain select pins G2A and G2B connected together.
3. All gain select pins open.
Philips Semiconductors Linear Products Product specification
µA733/733CDifferential video amplifier
April 15, 1992 265
TYPICAL PERFORMANCE CHARACTERISTICS
OVERDRIVE RECOVERY TIME – ns
70
60
50
40
30
20
10
00 20 40 60 80 100 120 140 160 180 200
DIFFERENTIAL INPUT VOLTAGE – mV
VS= +6V
TA= 25oC
GAIN 2
PHASE SHIFT – DEGREES
Phase Shift as a
Function of Frequency
0
-5
-10
-15
-20
-25 0 1 2 3 4 5 6 7 8 9 10
FREQUENCY – MHz
GAIN 2
VS= +6V
TA= 25oC
COMMON-MODE REJECTION RATIO – dB
Common-Mode Rejection Ratio
as a Function of Frequency
100
90
80
70
60
50
40
30
20
10
010k 100k 1M 10M 100M
FREQUENCY – Hz
GAIN 2
VS= +6V
TA= 25oC
OUTPUT VOLTAGE SWING – Vpp
Output Voltage Swing as
a Function of Frequency
7.0
6.0
5.0
4.0
3.0
2.0
1.0
01 5 10 50 100 5001000
FREQUENCY – MHz
VS= +6V
TA= 25oC
RL= 1kΩ
OUTPUT VOLTAGE – V
Pulse Response as a
Function of Supply Voltage
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
-0.2
-0.4-15 -10 -5 0 5 10 15 20 25 30 35
TIME – ns
GAIN 2
TA= 25oC
RL= 1kΩVS= +8V
VS= +3V
VS= +6V
OUTPUT VOLTAGE – V
TA= 70oC
Pulse Response as a
Function of Temperature
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
-0.2
-0.4 -15 -10 -5 0 5 10 15 20 25 30 35
TIME – ns
GAIN 2
VS= +6V
RL= 1kΩ
TA= 25oC
TA= 0oC
0
–60
–100
–150
–200
–250
–300
–3501 5 10 50 100 5001000
GAIN 3
GAIN 2
GAIN 1
VA= +6V
TA= 25oC
PHASE SHIFT — DEGREES
FREQUENCY — MHz
VS= +6V
TA= 25oC
RL= 1kKΩ
Phase Shift as a
Function of Frequency Voltage Gain as a
Function of Temperature
FREQUENCY — MHz
SINGLE ENDED VOLTAGE GAIN – dB
60
50
40
30
20
10
0
-10
GAIN 1
GAIN 2
GAIN 3
1 5 10 50 100 5001000
OUTPUT VOLTAGE – V
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
-0.2
-0.4 -15 -10 -5 0 5 10 15 20 25 30 35
TIME – ns
VS= +6V
TA= 25oC
RL= 1k
GAIN 2
GAIN 1
GAIN 3
Pulse Response
Differential Overdrive
Recovery Time
Philips Semiconductors Linear Products Product specification
µA733/733CDifferential video amplifier
April 15, 1992 266
TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
SUPPLY CURRENT – mA
Supply Current as a
Function of Temperature
21
20
19
18
17
16
15
14 -60 -20 20 60 100 140
TEMPERATURE – oC
VS= +6V
SINGLE ENDED VOLTAGE GAIN – dB
Gain vs. Frequency as a
Function of Temperature
60
50
40
30
20
10
0
-10 1 5 10 50 100 500 1000
FREQUENCY – MHz
GAIN 2
VS= +6V
RL= 1kKΩ
TA= 125oC
TA= –55oC
TA= 25oC
SINGLE ENDED VOLTAGE GAIN – dB
Gain vs. Frequency as a
Function of Supply Voltage
60
50
40
30
20
10
0
-10 1 5 10 50 100 500 1000
FREQUENCY – MHz
VS= +8V
VS= +3V
VS= +6V
GAIN 2
TA= 25oC
RL= 1kKΩ14
1
12 11 8
7
4
3
Voltage Gain
Adjust Circuit
0.2µF
0.2µF
733
51Ω51ΩRADJ 1kΩ1kΩ
TA= 25oCVS= +6V
(Pin numbers apply to K Package)
SUPPLY CURRENT – mA
28
24
20
16
12
83 4 5 6 7 8
SUPPLY VOLTAGE – +V
TA= 25oC
OUTPUT VOLTAGE SWING – V OR
OUTPUT SINK CURRENT – mA
Output Voltage and Current
Swing as a Function of
Supply Voltage
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0
3.0 4.0 5.0 6.0 7.0 8.0
SUPPLY VOLTAGE – +V
TA= 25oC
VOLTAGE
CURRENT
RELATIVE VOLTAGE GAIN
Voltage Gain as a
Function of Temperature
1.10
1.08
1.06
1.04
1.02
1.00
0.98
0.96
0.94
0.92
0.90 0 10 20 30 40 50 60 70
TEMPERATURE – oC
VS= +6V
GAIN 2
GAIN 1
GAIN 3
RELATIVE VOLTAGE GAIN
Voltage Gain as a
Function of Supply Voltage
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4 3 4 5 6 7 8
SUPPLY VOLTAGE – +V
TA= 25oC
GAIN 2 GAIN 1
GAIN 3
1000
100
10
10 100 1K 10K
RADJ – Ω
VS= +6V
TA= 25oC
DIFFERENTIAL VOLTAGE GAIN – V/V
Voltage Gain as a
Function of RADJ (Figure 3)
Supply Current as a
Function of Supply Voltage
Philips Semiconductors Linear Products Product specification
µA733/733CDifferential video amplifier
April 15, 1992 267
TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
OUTPUT VOLTAGE SWING – Vpp
Output Voltage Swing as a
Function of Load Resistance
7.0
6.0
5.0
4.0
3.0
2.0
1.0
010 50 100 500 1K 5K 10K
LOAD RESISTANCE – Ω
VS= +6V
TA= 25oC
INPUT RESISTANCE – KΩ
Input Resistance as a
Function of Temperature
70
60
50
40
30
20
10
0-60 -20 0 20 60 100 140
TEMPERATURE – oC
GAIN 2
VS= +6V
INPUT NOISE VOLTAGE – Vrmsµ
Input Noise Voltage as a
Function of Source Resistance
100
90
80
70
60
50
40
30
20
10
01 10 100 1K 10K
SOURCE RESISTANCE – Ω
GAIN 2
VS= +6V
TA= 25oC
BW = 10MHz
TEST CIRCUITS TA=25°C, unless otherwise specified.
VOUT
VIN RL
733
51Ω51Ω51Ω51Ω
ein
eout eout
1k 1k
0.2µF
0.2µF
733
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Philips Amplificatore
Philips
Philips TDA6107JF Manuale utente
Philips
Philips SA5223 Manuale utente
Philips
Philips TDA8566TH Manuale utente
Philips
Philips TDA2614 Manuale utente
Philips
Philips Fidelio DS6600 Manuale utente
Philips
Philips BGY88 Manuale utente
Philips
Philips FA761/00 Manuale utente
Philips
Philips CGY2014TT Manuale utente
Philips
Philips 22ah270 Manuale utente
Philips
Philips DFA 888 Manuale utente
Philips
Philips PM 3344 Manuale utente
Philips
Philips TDA8586 Manuale utente
Philips
Philips CMP400/93 Manuale utente
Philips
Philips Amplifier Manuale utente
Philips
Philips car power amplifier Manuale utente
Philips
Philips SWV2116 Manuale utente
Philips
Philips FA761 Manuale utente
Philips
Philips CMP400 Manuale utente
Philips
Philips FA741 Manuale utente
Philips
Philips TDA8943SF Manuale utente
