Philips MANT950 - TV Antenna - Indoor Manuale utente

MANT950

EENNUser manual 1

SSPPManual De Utilizador 9

EN Contents

33SSaaffeettyyIInnssttrruuccttiioonnss

55IInncclluuddeeddwwiitthhAAnntteennnnaa

55MMoouunnttiinnggAAnntteennnnaa

66CCoonnnneeccttiinnggttooyyoouurrTTVV

77WWaarrrraannttyy

88TTeecchhnniiccaallSSuuppppoorrtt

Antenna grounding and safety warning

1. Outdoor antennas and lead-in conductors from antenna to a build-

ing, should not cross over open conductors of electric light or

power circuits.They should be kept away from all circuits to avoid

the possibility of accidental contact.

2. Each conductor of a lead-in from an outdoor antenna should be

connected with an antenna discharge unit.Antenna dicharge units

(or Lightning Arrestors) should be located outside the building or

inside the building between the point of entrance of the lead-in and

the TV, and as near as practical to the entrance of the conductors

to the building.

Important Safety Notes

If you do not feel comfortable or competent to install this antenna we

recommend that you seek the assistance of a qualified professional

antenna installer.

Read the instructions for this device thoroughly before attempting

installation.

The installation or dismantling of any antenna near power lines is dan-

gerous. Each year hundreds of people are killed or injured while

attempting to install or service antennas. For your safety and proper

antenna installation, read and follow all safety precautions.

Choose an installation site for safety as well as performance.

All electric power lines, cable lines and telephone lines look alike.To

be safe, assume ANY overhead line can kill you.

Do not place an antenna where it could potentially fall on to, or blow

into a power line. If in doubt call your electric provider. Let them

review your site.

Outdoor antennas should be grounded with an approved lighting arrest-

ing device. Local codes may apply. Use 8 AWG or larger ground wire.

Height or other restrictions on antennas may apply to your installa-

tion depending on your proximity to an airport, or local ordinances.

Take the time to plan your installation procedure. Do all assembly

Safety Instructions

IIMMPPOORRTTAANNTT

RREEAADD

BBEEFFOORREE

IINNSSTTAALLLLAATTIIOONN

NEC -

National Electrical Code

*Antenna Discharge Unit is not required if lead in conductors are enclosed in a

continuous metallic shield that is permanently and effectively grounded.

GROUND CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD-IN WIRE

ANTENNA

DISCHARGE

UNIT*

(NEC

SECTION

810-20)

GROUNDING

CONDUC-

TORS

(NEC SEC-

TION 810-

21)

GROUND CLAMPS

POWER SERVICE GROUND-

ING ELECTRODE

SYSTEM (NEC ART250,

PART H)

TO EXTERNAL ANTENNA

TERMINALS OF PRODUCT

TO ROTATOR CONTROL UNIT

EN Safety Instructions

work on the antenna on the ground. Raise the completed antenna

after assembly.

Do NOT work on a wet, snowy or windy day or if a thunderstorm is

approaching. Do NOT use a metal ladder.

If the antenna assembly starts to fall, get away from it and let it fall.

Remember that the antenna mast and cable are all excellent conduc-

tors of electrical current.

Do NOT install the antenna by yourself. Be sure that there are two

other people available for help.

If any part of the antenna should come in contact with a power line .

.. DON'T TOUCH IT OR TRY TO REMOVE ITYOURSELF. Call your

local power company immediately.They will remove it.

Should an electrical accident occur ...DON'TTOUCHTHE PERSON

IN CONTACT WITH THE POWER LINE, or you too can become

electrocuted. Instead, use a DRY board, stick, or rope to push or pull

the victim away from the power lines and antenna. Once clear, check

the victim. If he has stopped breathing, immediately administer car-

diopulmonary resuscitation (CPR) and stay with him. Have someone

else call for medical help.

Install wire antennas high enough that they will not be "walked into"

by people.

Do not install antenna wire(s) over or under utility lines.

Important installation information

The MANT950 uses a power injector that sends a low power DC

voltage to the antenna to drive the signal amplifier built into the

antenna though the RG-6 or RG-59 signal cable.

It is essential for proper operation of this antenna system that the

power injector be connected between the antenna and any devices

such as splitters, additional amplifers, matching transformers, net-

works, etc. SEE DIAGRAM TO LEFT.

Disregarding this important notice may result in damaging the power

injector or improper operation / poor performance.

Parts included:

1. MANT950 Antenna 1

2. 12VDC, 200mA Power Injector 1

3. Main Bracket 1

4. 1/2" screws & washers) 6

5. U-Bolts 2

6. Mast clamps 2

7. Wing-nuts 4

7. L-Bracket 2

8. 2" Wood Screws 2

9. 20' RG-59U cable with connectors 1

10. Weather Boot 1

Determining signal strength

Before Installation determine the best location for optimum recep-

tion. It is important for the antenna to have an unobstructed path to

the transmitter.To determine the transmitter(s) location you can con-

sult the website http://www.antennaweb.org. For best results the

antenna should be facing to the transmitter locations as shown at left.

Wall mounting the unit (indoor or outdoor)

Do all the antenna assembly work on the ground. Raise the complet-

ed antenna after assembly.

1. Attach the main bracket to the antenna assembly using the 6 - 1/8”

screws and washers as shown in Figure A.

2. Attach the L brackets to the unit as shown in figure B. Note that

the brackets are adjustable laterally for best mounting.

3. Using the L brackets as a guide mark position for the two 2” wood

screws. If possible locate a stud to screw into, adjusting the L brack-

ets accordingly.If studs are not available use appropriate wall anchors

(not included, available at any hardware store). Screw the wood

Included with Antenna

Mounting Antenna

Fig A

EN Mounting Antenna

screws into the wall but leave about 1/2” to allow for the last step.

4. Attach the cable to the F connector on the underside of the unit

and slide the weather protection boot over the connection.

5. Hook the top of the L brackets onto the wood screws through the

keyholes. Make sure the screws are at the top of the keyhole. At

this point tighten the wood screws fully into position and tighten

the L bracket screws.

Mast Mounting or Attic Mounting

(Mast not included)

Do all the antenna assembly work on the ground. Raise the complet-

ed antenna after assembly.

1. Install the two U-bolt s from the rear of the main bracket.

2. Attach the main bracket to the antenna assembly using the 6 - 1/8”

screws and washers as shown in Figure A above.

3. Attach the U-Bolt clamps with the pointed side facing outward.

4. Place the 4 wing-nuts on the threads of the U-bolts – loosely

allowing space for the mast.

5. Slide the top of the mast under the clamps – and fully tighten the

wing-nuts.The completed assembly should look like figure C.

6. Attach the cable to the F connector on the underside of the unit

and slide weather protection boot over the connection.

7. Attach the mast to the mast mount and fasten hardware for the

mast (not included).

As previously noted the power injector must be placed in-line

between the antenna and before any splitter or additional devices.

1. Connect the coaxial cable from the antenna to the F connector

labeled ANT on the power injector.

2. Connect the short lead from the power injector to the antenna

input on your TV.

3. Connect the power supply lead to the power injector, then plug

the power supply into a 110/120 Volt AC receptacle.

Fig C

Fig B

Connecting to your TV

SSaaffeettyyNNoottee--TThheeppoowweerriinnjjeeccttoorraannddppoowweerrssuuppppllyyiissffoorr

iinnddoooorruusseeoonnllyy!!

Alternate connections

1. If your TV has separate inputs for UHF and VHF you will need to

purchase a signal splitter that will separate the two different sig-

nals

2. If your TV has only two screw type antenna inputs you will need

to purchase a 75 Ohm to 300 Ohm transformer.

A note about coaxial cable –Your Mant 950 includes a 20 foot roll of

RG-59 coaxial cable. If you should find that this is not adequate for

your needs we recommend for best possible signal integrity that you

do not extend this cable.A better choice is to replace the cable with

either RG-6 or RG-6 Quad Shield cable. Both of these cables are

designed for minimal signal loss over longer cable runs. This will

ensure the best possible picture and overall performance.

Limited Lifetime Warranty

The manufacturer warrants that this product shall be free from

defects in material, workmanship and assembly, under normal use,

in accordance with the specifications and warnings, for as long as

you own this product.This warranty extends only to the original

purchaser of the product, and is not transferable. Defective prod-

ucts, together with the dated proof of purchase, must be returned

to the place of purchase for repair or replacement.THERE ARE NO

OTHER EXPRESS WARRANTIES. Incidental and consequential

damages are disclaimed where permitted by law. This warranty

gives you specific legal rights, and you may also have other rights

which vary from state to state.

Warranty

EN Technical Support

Technical Support

ForTechnical support send an email with the model number of the

product and a detailed description of your problem to:

Email: [email protected]

Accessories Service Center

Philips

Accessories and Computer Peripherals,

Ledgewood, NJ 07852 USA

Quality assured in USA

Printed in China

Contenido

3 Instrucciones de seguridad

5 Partes incluidas:

13 Montaje de la antena

15 Conexión de su TV

15 Garantía limitada por vida

15 Asistencia Técnica:

SP Instrucciones de seguridad

Conexión a tierra de la antena y advertencia de

seguridad.

1. Las antenas exteriores y los conductores de bajada de antena a un edi-

ficio, no deben atravesar conductores abiertos de luz eléctrica o cir-

cuitos de transmisión de energía. Deben mantenerse alejados de

cualquier circuito para evitar la posibilidad de contacto accidental.

2. Cada conductor de bajada de una antena exterior debe conectarse a

una unidad de descarga de antena.Las unidades de descarga de antena

(o pararrayos) deben ubicarse en el exterior del edificio o en el interi-

or, entre el punto de entrada de la bajada y elTV, y tan cerca como sea

posible de la entrada de los conductores al edificio.

Notas importantes de seguridad –

Si no se siente cómodo para instalar esta antena o siente que no

eres capacitado para hacerlo, le recomendamos que busque ayuda de un

colocador de antenas profesional calificado.

Lea bien las instrucciones correspondientes a este dispositivo antes de inten-

tar hacer la instalación.

La instalación o desinstalación de una antena cerca de las líneas de energía

es peligroso. Cada año cientos de personas mueren o resultan heridas

mientras intentan instalar o hacer el mantenimiento de antenas. Por su

seguridad y para que la antena quede instalada adecuadamente, lea y

cumpla todas las precauciones de seguridad.

Elija un lugar para la instalación teniendo en cuenta la seguridad y el

rendimiento.

Todas las líneas de energía eléctrica, líneas de cable y telefónicas parecen

iguales. Para estar seguro,asuma queTODO cable aéreo puede matarlo.

No coloque una antena donde pueda caer sobre los cables de energía o gol-

pearlos. Si tiene dudas, llame la empresa de energía eléctrica. Permítales

revisar el lugar.

Las antenas exteriores deben estar colocadas con un dispositivo luminoso

distintivo aprobado. Pueden aplicarse los códigos locales. Use 8 AWG o

un cable de tierra más grande.

IIMMPPOORRTTAANNTTEESS

LLEEEERRAANNTTEESSDDEE

IINNSSTTAALLAARR

NEC -

National Electrical Code

* Antenna Discharge Unit is not required if lead in conductors are enclosed in a contin-

uous metallic shield that is permanently and effectively grounded.

Grapa de puesta a tierra

Equipo de

servicio eléctrico

Cable de bajada

de antena

Unidad de

descarga de

antena*

(NEC SECTION

810-20)

Conductores

de puesta a

tierra (NEC

SECTION 810-

21)

Sistema de

electrodos de

puesta a tierra

del servicio de

energía eléctri-

ca. (NEC ART

250, PART H)

A terminales de antena

externos del producto

A la unidad de

control del rotator

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Philips Antenna

Philips

Philips SDV1121T/27 Manuale utente

Philips

Philips SDV8311B/27 Manuale utente

Philips

Philips SWS2083W Manuale utente

Philips

Philips SDV7700K/17 Manuale utente

Philips

Philips SDV9201K Manuale utente

Philips

Philips SDV1227B/27 Manuale utente

Philips

Philips SDV9201/17 Manuale utente

Philips

Philips SBCTT100/05 Manuale utente

Philips

Philips SDV9201 Manuale utente

Philips

Philips SDW1850/17 Manuale utente

Philips

Philips SDV7114A Manuale utente

Philips

Philips SDV2750/27 Manuale utente

Philips

Philips SDW1850/17 Manuale utente

Philips

Philips SDV2710/27 Manuale utente

Philips

Philips SDV4401/27 Manuale utente

Philips

Philips SDV3427W/27 Manuale utente

Philips

Philips MANT901 Manuale utente

Philips

Philips SDW1420 Manuale utente

Philips

Philips SDV9011K Manuale utente

Philips

Philips TT300 Manuale utente

Philips

Philips US2-MANT901 - Tv Antenna Uhf/vhf/fm/hdtv... Manuale utente

Philips

Philips SDW1410GN Manuale utente

Philips

Philips SDV2780 - HDTV Antenna - Indoor Manuale utente

Philips

Philips SDV2720/27 Manuale utente

Manuali Antenna popolari di altre marche

Alfa Network

Alfa Network APA-L01 Manuale utente

Naval

Naval PR-422CA Manuale utente

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuale utente

TERK Technologies

TERK Technologies TV44 Manuale utente

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuale utente

HP J8999A Manuale utente

MobilSat

MobilSat MSP-S Manuale utente

Steren

Steren ANT-UHF 13 Manuale utente

Novatel

Novatel 600-G Manuale operativo

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuale utente

TRENDnet

TRENDnet TEW-AO12O Manuale utente

Radio Shack

Radio Shack 15-1837 Manuale utente

CommScope

CommScope CMAX-OMFX-43M-I53 Manuale utente

Ramsey Electronics

Ramsey Electronics DAP25 Manuale utente

COBHAM

COBHAM SAILOR 800 VSAT Manuale per l'uso e la cura

Trango Systems

Trango Systems AD900-9 Manuale utente

Steren

Steren ANT-100 Manuale utente

Proxim

Proxim 5054-PA-23 Manuale utente