Philips BT9280 Manuale utente
Always here to help you
User manual
Register your product and get support at
www.philips.com/welcome
BT9295
BT9290
BT9280
1
4
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers, register your
product at www.philips.com/welcome.
General description (Fig. 1)
1 Precision trimming comb
2 Standard trimming comb
3 Turnable trimming head
4 Laser guide
5 Guiding groove for trimming comb
6 Length setting display
7 Zoom wheel for length setting
8 On/off button
9 Battery lights
10 Socket for small plug
11 Adapter
12 Small plug
13 Cleaning brush
14 Storage pouch (BT925/BT9290 only)
Important
Read this user manual carefully before you use the appliance and save it for
future reference.
Danger
- Keep the adapter dry.
Warning
- Check if the voltage indicated on the adapter corresponds to the local
mains voltage before you connect the appliance.
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
- Keep the appliance and its cord out of the reach of children.
- Do not use the appliance in the bath or in the shower.
Caution
- Always check the appliance before you use it. Do not use the appliance
if any of its parts is damaged or broken, as this may cause injury.
- Only use this appliance for its intended purpose as shown in the user
manual.
- Use, charge and store the appliance at a temperature between 5°C
and 35°C.
- Only use the adapter supplied to charge the appliance.
- Make sure the appliance is switched off and disconnected from the
mains before you clean it under the tap.
ENGLISH
- If the appliance is subjected to a major change in temperature,
pressure or humidity, let the appliance acclimatise for 30 minutes
before you use it.
- If the adapter is damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- Never use compressed air, scouring pads, abrasivecleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
- Noise level: Lc= 65dB(A)
Compliance with standards
- The appliance complies with the internationally approved IEC safety
regulations and can be safely cleaned under the tap.
- This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic elds.
Class 1 laser product
- The product contains a class 1 laser guide which complies with
IEC60825-1.
- To avoid all risks, point the laser beam away from your eyes and do not
stare directly into the laser beam.
Preparing for use
Charging
Charge the appliance fully before you use it for the rst time and after a
long period of disuse.
Charging takes about 60 minutes if the appliance is completely empty.
1 Make sure the appliance is switched off and the laser guide is in ‘off’
position.
2 Insert the small plug into the appliance and put the adapter in the
wall socket.
,First the bottom battery light ashes orange and white alternately.
ENGLISH 5
,After about 3 minutes the bottom battery light ashes white only.
At this point the battery contains enough energy for one cordless
trimming session.
,When the charging process continues, more lights start ashing to
show that the charge level of the battery increases.
,When the appliance is fully charged, all battery lights light up solid
white.
If the appliance is still connected to the mains when it is fully charged, the
battery lights go out after 30 minutes.
Battery low and battery empty signals
,When the battery is almost empty, the bottom battery light starts
ashing orange. When you switch off the appliance, the bottom
battery light continues to ash orange for a few seconds.
,The battery light at the bottom of the appliance ashes orange at a
higher frequency when the battery is empty and if you:
- press the on/off button
- turn the zoom wheel
- activate the laser guide
Corded trimming
You can also operate the appliance from the mains.
1 Insert the small plug into the socket of the appliance.
2 Put the adapter in a wall socket.
3 Press the on/off button to switch on the appliance.
ENGLISH6
Using the appliance
You can use the appliance to trim facial hair (beard, moustache and
sideburns).This appliance is not intended for trimming lower body parts or
scalp hair.
Trimming with the laser guide
You can use the laser guide to dene the edges of your beard, sideburns
and moustache.The laser guide can be used with the 32mm (1.25in) side
as well as the 15mm (0.6in) side of the trimming head.
Note:The laser guide can only be used when you trim without comb.
Note:Although the light from the laser guide is not harmful to the eyes, we
advise you not to stare into the light and to avoid shining the light into your
eyes.
1 Press the on/off button to switch on the appliance.
2 To trim with the laser guide, press the top of the laser guide to
switch it on.
,The laser guide pops up and its light shines over the top of the
trimming head.
Note: If you trim with the laser guide, make sure you push the laser guide to
‘off ’ position before you turn the trimming head.You may damage the laser
guide if you try to turn the trimming head while the laser guide is still
popped up.
ENGLISH 7
3 Start trimming where you want to dene the edges of your beard
and use the laser guide to guide you during trimming.
Tip: Hold the appliance so that the laser light shines exactly on the edge you
want to trim and then place the trimming head on your skin.
4 When you are nished, press the on/off button to switch off the
appliance.
Tip:When the motor of the appliance is not operating, the laser guide switches
off automatically within 3 minutes. In the 3 minutes before the automatic
switch-off of the laser guide, you can use the laser guide to check if the
contours of your beard are symmetrical or straight.
5 Push down the top of the laser guide to lock it in ‘off’ position
(‘click’).
Trimming without comb
If you trim without comb, your hair is cut off close to the skin. The trimming
head has a 32mm (1.25in) side and a 15mm (0.6in) side.The 15mm (0.6in)
side of the trimming head allows more precise styling and contouring than
the 32mm (1.25in) side.
1 If one of the combs is still on the trimming head, pull it off.
Never pull at the exible top of the comb. Always pull at the sides.
2 Turn the trimming head until the side you want to use points to the
front of the appliance.
ENGLISH8
3 Press the on/off button to switch on the appliance.
4 Hold the appliance in the position that is most convenient for the
area you want to trim and make strokes in the desired direction.
Tip: For a comfortable trim close to your skin, place the at side of the
trimming head against your skin and make strokes in the desired direction.
5 When you are nished, press the on/off button to switch off the
appliance.
Trimming with comb
The appliance comes with two combs: a standard comb and a precision
comb.These combs keep the trimming head at a certain distance from
your skin.This distance determines the remaining hair length and can be
adjusted by turning the zoom wheel.
- Use the standard comb to trim your beard.
- Use the precision comb to trim hard-to-reach areas, for instance under
your nose.
1 Slide the comb into the guiding grooves on both sides of the
appliance (‘click’).
Note: The comb does not t on the trimming head when the 15mm (0.6in)
side is pointing towards the front of the appliance. If this is the case, turn the
trimming head before you slide the comb onto the trimming head.
2 Turn the zoom wheel to select a length setting.
- The length setting selected lights up on the front of the appliance.
- You can select a length from 0.4mm to 7mm (see table in section
‘Length settings’ below).
ENGLISH 9
3 Press the on/off button to switch on the appliance.
4 To trim your beard, move the trimming comb through the
hair slowly.
5 When you are nished, press the on/off button to switch off the
appliance.
Tips
- Always make sure that the tips of the trimming comb point in the
direction in which you move the appliance.
- Make sure that the at part of the trimming comb is always in full
contact with the skin to obtain an even hair length result.
- Since hair grows in different directions, you need to move the appliance
in different directions (upward, downward or across).
- Trimming is easier when skin and hair are dry.
Length settings
mm
0.4 0.6 0.8 1.0 1.2
1.4 1.6 1.8 2.0 2.5
3.0 3.5 4.0 4.5 5.0
6.0 7.0
Cleaning and maintenance
Clean the appliance after every use.
Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
Note:The trimming head does not need any lubrication.
ENGLISH10
Questo manuale è adatto per i seguenti modelli
9
Indice
Lingue:
Altri manuali Philips Rasoio elettrico
Philips
Philips S588 Manuale utente
Philips
Philips S3580 Manuale utente
Philips
Philips HQ7120 Manuale utente
Philips
Philips Coolskin HS8060 Manuale utente
Philips
Philips BT1005 Manuale utente
Philips
Philips HQ 7742 Manuale utente
Philips
Philips BG1024/16 Manuale utente
Philips
Philips Click & Style YS534/17 Manuale utente
Philips
Philips 8200 series Manuale utente
Philips
Philips S5000 series Manuale utente
Philips
Philips Norelco 7180XL Manuale utente
Philips
Philips MG7720 Manuale utente
Philips
Philips S3552 Manuale utente
Philips
Philips NORELCO SP9883 Manuale utente
Philips
Philips Essence 5000 Series Manuale utente
Philips
Philips Essence 5000 Series Manuale utente
Philips
Philips RQ11 series Manuale operativo
Philips
Philips QG3320 Manuale utente
Philips
Philips Satinelle Massage HP6463 Manuale utente
Philips
Philips QT4015 Manuale utente
