Philips Bodine LP400 Manuale utente

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

SAVE THESE INSTRUCTIONS

THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.

THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.

A Division of Philips Electronics North America Corporation

236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.philips.com/bodine

70100194

Installation Instructions

1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter

connector must be open. Do not join inverter connector until installation is complete and AC power is

supplied to the emergency ballast.

2. This product is for use with one (4') 32 W T8 bipin uorescent lamp.

3. Make sure all connections are in accordance with the National Electrical Code and any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and

inverter connector of the emergency ballast before servicing.

5. This emergency ballast is for factory or eld installation in the ballast channel or on top of xture.

6. This product is for use in indoor xtures except air handling heated air outlets, and wet, damp, or

hazardous locations.

7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not eld

replaceable. Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe

condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualied service personnel.

CAUTION: Verify that all replacement lamp types marked on the installed luminaire are also identied as suit-

able for use with this inverter/charger pack.

LP400

Ni - Cd

08/01/13

EMERGENCY LIGHTING EQUIPMENT

STEP #1 INSTALLING THE EMERGENCY BALLAST

> Disconnect AC power from the xture. Remove the

ballast channel cover and install the emergency

ballast in the ballast channel (see Illustration 1).

> Remote mounting distance must be less than half

the maximum remote mounting distance for the

AC ballast. Consult AC ballast manufacturer

before remote installation.

STEP #2 INSTALLING THE TEST SWITCH

> Refer to Illustration 2 and install the test switch

through the ballast channel cover of a troffer or

through the side of a strip xture.

> Drill a 1/2" hole and install the switch as shown.

> Wire the test switch so that it removes AC power

from both the emergency ballast and the AC ballast

at the same time (see Illustration 3).

STEP #3 INSTALLING THE CHARGING

INDICATOR LIGHT

> Refer to Illustration 3A or 3B and install the charg-

ing indicator light so that it will be visible after the

xture is installed.

WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED & YELLOW OUTPUT

LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. DO NOT JOIN

INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED

TO THE EMERGENCY BALLAST.

NOTE: Make sure that the necessary branch circuit wiring is available. An unswitched

source of power is required. The emergency ballast must be fed from the same

branch circuit as the AC ballast.

ILLUSTRATION 1

ILLUSTRATION 2

INSTALLATION

UNSWITCHED FIXTURE SWITCHED FIXTURE UNSWITCHED FIXTURE SWITCHED FIXTURE

SINGLE POLE DOUBLE POLE OPTION

BLACK 120V

ORANGE 277V

BLACK AC

BALLAST

EMERGENCY

BALLAST

WHITE

HOT

COM (CAP UNUSED LEAD)

SINGLE POLE

TEST SWITCH

(Breaking the Hot)

BLACK 120V

ORANGE 277V

BLACK

EMERGENCY

BALLAST

WHITE

HOT

COM

(CAP UNUSED LEAD)

SINGLE POLE

TEST SWITCH

(Breaking the Common)

BLACK 120V

ORANGE 277V

BLACK

EMERGENCY

BALLAST

WHITE

HOT

COM (CAP UNUSED LEAD)

SINGLE POLE

TEST SWITCH

(Breaking the Hot)

BLACK 120V

ORANGE 277V

BLACK

EMERGENCY

BALLAST

WHITE

HOT

COM

(CAP UNUSED LEAD)

SINGLE POLE

TEST SWITCH

(Breaking the Common)

WALL

SWITCH

WALL

SWITCH

BALLAST

BLACK 120V

ORANGE 277V

BLACK AC

BALLAST

EMERGENCY

BALLAST

WHITE

BLK

HOT

COM

RED RED

(CAP UNUSED LEAD)

BLK WALL

SWITCH

BLACK 120V

ORANGE 277V

BLACK AC

BALLAST

EMERGENCY

BALLAST

WHITE

BLK

HOT

COM

RED RED

(CAP UNUSED LEAD)

DOUBLE POLE

TEST SWITCH

BLK

DOUBLE POLE

TEST SWITCH

ILLUSTRATION 3

Fixture

Test Button

Hex Nut

Test Switch

Leads

Push to Test

STEP #4 WIRING THE EMERGENCY BALLAST

> Select the appropriate wiring diagram and connect the emergency ballast to the AC ballast and lamp(s). Make

sure all connections are in accordance with the National Electrical Code and any local regulations.

> After installation is complete, supply AC power to the emergency ballast and join the inverter connector.

> At this point, power should be connected to both the AC ballast and the emergency ballast, and the Charging

Indicator Light should illuminate indicating the battery is charging.

> A short-term discharge test may be conducted after the emergency ballast has been charging for one hour.

Charge for 24 hours before conducting a long-term discharge test. Refer to OPERATION.

> In a readily visible location, attach the label "CAUTION - This Unit Has More Than One Power Connection PointTo

Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency Power

Supplies Before Servicing."

When AC power is applied, the charging indicator light is illuminated, indicating that the battery is being charged. When

power fails, the emergency ballast automatically switches to emergency power, operating one lamp at reduced illumination.

This emergency ballast will operate one (4') 32 W T8 bipin lamp for a minimum of 90 minutes.

Although no routine maintenance is required to keep the emergency ballast functional, it should be checked periodically to

ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated.

2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds.

One lamp should operate at reduced illumination.

3. Conduct a 90-minute discharge test once a year. One lamp should operate at reduced

illumination for at least 90 minutes.

! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !

MAINTENANCE

OPERATION

NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label. If a

detached charging indicator light is used, connect by matching wire colors and install as shown above.

STEP 2STEP 1

ILLUSTRATION 3B

ILLUSTRATION 3A

Charging

Indicator

Light

1/2" White

Bushing

Violet (+)

Brown (–)

Violet (+)

Brown (–)

1/2" White

Bushing

5/8" Black

Bushing 5/8" Black

Bushing

1/2" Punch

Fixture Fixture

Charging

Indicator

Light

WIRING DIAGRAM for EMERGENCYONLY xtures

EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION

FIG D TWO (2) LAMP RAPID START BALLAST

FIG C TWO (2) LAMP INSTANT START BALLAST

FIG F THREE (3) LAMP RAPID START BALLAST

FIG G FOUR (4) LAMP INSTANT START BALLAST FIG H FOUR (4) LAMP RAPID START BALLAST

FIG E THREE (3) LAMP INSTANT START BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

( )

EMERGENCY

LAMP 1

LAMP 2

BLACK

WHITE

YELLOW

LINE

RED

BLUE

BALLAST

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2

LAMP 3

BLACK

WHITE

LINE

RED

BLUE

BLUE BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST BLUE

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2

LAMP 3( )

EMERGENCY

BLACK

WHITE

YELLOW

LINE

RED

BLUE/WHT

BLUE

BLUE BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2

LAMP 3

LAMP 4( )

EMERGENCY

BLACK

WHITE

YELLOW

LINE

RED

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

BLUE

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2

LAMP 3

LAMP 4

BLACK

WHITE

YELLOW

BROWN

LINE RED

RED

BLUE/WHT

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2 (EMERGENCY)

BLACK

WHITE

LINE BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST RED

BLUE

FIG B ONE (1) LAMP RAPID START BALLAST

FIG A ONE (1) LAMP INSTANT START BALLAST

FIG I ONE (1) 17-215 W LAMP WITHOUT AC BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

CAP

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP

BLACK

WHITE

RED

LINE BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

BLUE

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

BLACK

WHITE

LINE

RED

BLUE

BALLAST

LAMP

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

Indice

Altri manuali Philips Attrezzatura di illuminazione

Philips

Philips RC095V Manuale utente

Philips

Philips Selecon Accent LED Beamshaper Manuale utente

Philips

Philips 56432-31-16 Manuale utente

Philips

Philips ColorBlast 6 Guida all'installazione

Philips

Philips Ecomoods 57940/31/96 Manuale utente

Philips

Philips eW Cove QLX Powercore Manuale utente

Philips

Philips 59273-17-16 Manuale utente

Philips

Philips hue Manuale utente

Philips

Philips BN012C Guida utente

Philips

Philips Lightstrip Plus 71901/U8 Series Manuale utente

Philips

Philips GreenPower LED Manuale utente

Philips

Philips Softone 871150066257610 Manuale utente

Philips

Philips Disney Softpal Mickey Manuale utente

Philips

Philips LCN9620 Manuale utente

Philips

Philips ColorGraze Powercore Manuale utente

Philips

Philips B50ST Manuale utente

Philips

Philips Hadco BUL16 MICRO BULLYTE Manuale utente

Philips

Philips hue Manuale utente

Philips

Philips hue 40801 Series Manuale utente

Philips

Philips Vaya Flood HP 150W Manuale utente

Philips

Philips 56422-31-16 Manuale utente

Philips

Philips RS772B Manuale utente

Philips

Philips RD6 Manuale utente

Philips

Philips Light System Manager Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente

Philips bodine LP400 Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche