Philips FC8932 Manuale utente
FC8932, FC8832,
FC8830
FC8932, FC8832,
FC8830
1
Wheels stuck
ݓઁሂ
To p cover or dust container not placed properly
רۆࠋࠦӧ٦ݾ
Bumper stuck
ߓԎሑᇆሂ
Robot lifted up from floor
՚ֽϴุఓᇊୃስײᆋ༏ӧచ
Colour of floor too dark
ֽϴဂ೨ขτ
Battery not inserted properly / Charging error (switch is off)
ԁሑݾԍմ༆IJܵၜܵтij
5
6
4
3
2
1
7
8
9
10
16
14
13
15
12
11
17
19
18
20
22
21
2625
24
27
23
English 6
简体中文 27
Introduction
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips oers, register your product at
www.philips.com/welcome.
General description
1 Handle of dust container lid
2 Dust container lid
3 Filter
4 Dust container
5 Top cover
6 Error code table
7 Fan
8 Bumper
9 Docking station sensor
10 Display
11 Power switch (to switch the robot on or o)
12 Front wheel
13 Side brush shafts
14 Drop-o sensors
15 Wheels
16 TriActive XL nozzle
17 Side brushes
18 Fixation blocks for dry wipes
19 Dry wipe holder
20 Dry wipes
21 Battery holder
22 Remote control
23 AA batteries for invisible wall
24 Invisible wall
25 Docking station
26 Adapter
27 Small plug
Remote control and display
Display
1 Spiral mode indicator
2 Wall-following mode indicator
3 Zigzag pattern mode indicator
4 Random mode indicator
5 Cleaning time
6 Docking icon
7 WiFi icon
8 Dustbin full indicator
9 Sound sensor
10 Mode selection button
11 Start/stop button
12 WiFi button
1
1110 129
2
3
4
5 6 7 8
6English
Remote control (FC8932)
1 Navigation buttons and start/stop
2 Cleaning time buttons
3 Cleaning mode buttons
4 Fan speed buttons
5 Docking button
How your robot works
What your robot cleans
This robot is equipped with features that make it a suitable cleaner to help
you clean the oors in your home.
The robot is especially suitable for cleaning hard oors, such as wooden,
tiled or linoleum oors. It may experience problems cleaning soft oors,
such as carpet or rugs. If you use the robot on a carpet or rug, please stay
close by the rst time to see if the robot can deal with this type of oor.
The robot also needs supervision when you use it on very dark or shiny
hard oors.
How your robot cleans
Cleaning system
The robot has a 3-stage cleaning system to clean your oors eciently.
-The two side brushes help the robot clean in corners and along walls.
They also help to remove dirt from the oor and move it towards the
suction opening.
-The suction power of the robot picks up loose dirt and transports it
through the suction opening into the dust container.
-The robot comes with a dry wipe holder that allows you to clean your
hard oor even more thoroughly with dry wipes.
2
1
3
45
7
English
Cleaning patterns
In its auto cleaning mode, the robot uses an automatic sequence of cleaning
patterns to clean each area of the room optimally. The cleaning patterns it
uses are:
1 Z-pattern or zigzag pattern
2 Random pattern
3 Wall-following pattern
4 Spiral pattern
In its auto cleaning mode, the robot uses these patterns in a xed
sequence:z-pattern, random pattern, wall-following pattern, and spiral
pattern.
When the robot has completed this sequence of patterns, it starts moving
in Z-pattern again. The robot continues to use this sequence of patterns to
clean the room until the rechargeable battery runs low, or until it is switched
o manually.
If the robot detects a particularly dirty area during its cleaning run, it
switches to spiral mode and switches to turbo fan speed (FC8820 only) to
ensure thorough dirt removal.
Note: You can also select each mode individually by pressing the
appropriate button on the remote control (FC8932 only). The manually
selected modes are only active for a couple of minutes. After that, the robot
switches back to auto-cleaning mode.
For more details, see chapter 'Using your robot', section 'Cleaning modes'.
8English
How your robot avoids height dierences
The robot has three drop-o sensors in its bottom. It uses these drop-o
sensors to detect and avoid height dierences such as staircases.
Note: It is normal for the robot to move slightly over the edge of a height
dierence, as its front drop-o sensor is located behind the bumper.
Caution: In some cases, the drop-o sensors may not detect a staircase
or other height dierence in time. Therefore monitor the robot carefully
the rst few times you use it, and when you operate it near a staircase
or another height dierence. It is important that you clean the drop-
o sensors regularly to ensure the robot continues to detect height
dierences properly (see chapter ' Cleaning and maintenance' for
instructions).
Before rst use
Mounting the side brushes
1 Unpack the side brushes and place the robot upside down on a table or
on the oor.
2 Push the side brushes onto the shafts on the bottom of the robot.
Note: Make sure you attach the side brushes properly. Press them onto
the shaft until you hear them lock into position with a click.
Removing the tag from the remote control
The remote control works on a CR2025 coin-shaped battery. This battery is
protected with a protection tag that has to be removed before use.
1 Pull the battery protection tag out of the battery compartment of the
remote control. Now the remote control is ready for use.
9
English
Preparing for use
Installing the docking station
1 Insert the small plug of the adapter into the socket on the docking station
(1) and insert the adapter into the wall socket (2).
-The display of the docking station comes on.
2 Place the docking station on a horizontal, level oor against the wall.
Note: Make sure that there are no obstacles or height dierences 80 cm
in front, 30 cm to the right and 100 cm to the left of the docking station.
Tip: To ensure the docking station stays rmly in the selected spot,
fasten it to the wall with screws or with two strips of double-sided tape.
Charging
When charging for the rst time and when the rechargeable battery of the
robot is empty, the charging time is four hours.
Your robot can be charged in two ways:
-On the docking station, either manually or automatically during use;
-By connecting the robot directly to the mains.
Charging on the docking station
1 Place the robot on the plugged-in docking station.
2 Press the power switch to switch on the robot.
1
2
100 厘米 30 厘米
80 厘米
10 English
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Philips Aspirapolvere
Philips
Philips FC8820 Manuale utente
Philips
Philips FC9185/01 Manuale utente
Philips
Philips FC9179 Manuale utente
Philips
Philips XB2023/01 Manuale utente
Philips
Philips FC8767/02 Manuale utente
Philips
Philips Vision Manuale utente
Philips
Philips AquaTrio FC7070 Manuale utente
Philips
Philips 8000 Series Manuale utente
Philips
Philips Marathon FC9219 - FC9200 Manuale utente
Philips
Philips FC8323/09 Manuale utente
Philips
Philips BP300 Manuale utente
Philips
Philips FC9236 Manuale utente
Philips
Philips EasyStar FC8802 Manuale utente
Philips
Philips FC8820 Manuale utente
Philips
Philips FC6094 Manuale utente
Philips
Philips FC8796 Manuale utente
Philips
Philips FC9306/02 Manuale utente
Philips
Philips FC6067/01 Manuale utente
Philips
Philips FC8760 Manuale utente
Philips
Philips FC8140 Manuale utente
