Philips DVR7100/75 Manuale utente
Service Manual
Service
Service
Service
Service
Service
DVR5100/75 & DVR7100/75
©Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by ZW-KC 0716 AV System Printed in The Netherlands Subject to modification
GB
3139 785 32780
HDD Recorder
Version 1.0
TABLE OF CONTENT
1 General
1.1 Scope
1.2 Operating Conditions
2 H/W Speci ication
3 Adjustment & Setting
3.1 Re-install the set to actory settings a ter repair
3.2 Re- ormat HDD
4 S/W Upgrade Procedure
5 Troubleshooting Flowchart
6 Block Diagram & Wiring diagram
7 Mechanical Exploded view & Packaging drawing
8 Service Parts list
9 Annex - Circuit Diagram attachments
2
3
1. General
1. 1 Scope
This is the product sheet for the High-Definition (HD) Free to Air (FTA) MPEG2
Digital Video ecorder Set top box (STB) model DV 5100/75 with 160GB HDD and
DV 7100/75 with 250GB HDD. This HD DV is fully MPEG2 / DVB-T compliant,
supporting channel frequencies range of 51 – 858MHz.
DV 5100/75 and DV 7100/75 is a custom made product for Philips Consumer
Electronics, and has HDMI feature connectors for Digital Audio/Video output along
with S-Video, YPbPr and Composite connectors.
1.2. Operating Conditions
Operating Temperature : +/- 0°C ~ +55°C
Before delivery of the product, the supplier shall submit the specification drawing, the
sample, the test report and the QC (quality control) process flow chart to Philips
Singapore.
4
2. Hardware Speci ication
System
Tuners: Two digital HD tuners (to receive digital
transmission, see Basic Connection page 12-15)
Transmission standards: DVB-T
Channel coverage: 51 - 858 MHz. The above channel coverage merely ensures the
channel reception within these ranges. It does not guarantee the ability to receive signals in
all circumstances.
Aerial out: 75-ohm asymmetrical aerial socket
Video ormat: MP@ML, MP@HL
Audio ormat: Dolby Digital, MPEG (I and II)
Outputs
AUDIO OUT: CA jacks (2 each)/2 Vrms/10 kilo ohms
VIDEO OUT: CA jack/1.0 Vp-p/75 ohms
S VIDEO OUT: 4-pin mini DIN/Y:1.0 Vp-p,C: 0.3 Vp-p (PAL)/75 ohms
DIGITAL AUDIO OUT (OPTICAL): Opticaloutput jack/–18 dBm (wave length: 660
nm)
DIGITAL AUDIO OUT (COAXIAL): CAjack/0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT
(Y, PB/CB, PR/CR):
CA jack/Y: 1.0 Vp-p, PB/CB: 0.7 Vp-p,
P /C : 0.7 Vp-p/75 ohms
HDMI OUT:Type A (19-pin)
5
General
Power requirements: 220-240 V AC, 50 Hz
Power consumption:
DV 7100 : 30 W
DV 5100 : 29 W
Dimensions (approx.): 430 _ 80 _ 290 mm
(width/height/depth) incl. projecting parts
Hard disk drive capacity:
DV 7100 : 250GB
DV 5100 : 160GB
Mass (approx.): 4.0 kg
Operating temperature: 5ºC to 40ºC
Storage temperature: -40ºC to +65ºC
3. Adjustments & Settings :
3.1 Re-install the Set to Factory Settings a ter Repair:
Goto Main Menu -> General -> Reset settings:
This feature enables you to return the setup settings to their defaults without affecting
the recorded titles in the HDD.
Select { Yes }, and press OK.
The setup settings return to their defaults, and the recorder automatically turns off.
3.2 Re- ormat HDD:
Goto Main Menu -> HDD Setting -> Erase HDD:
Erases all the recorded titles in the HDD at once. Note that protected titles are also
erased.
Press OK to confirm and press BACK to exit.
6
7
4. S/W UPGRADE PROCEDURE
4.1 Use a crossover RS232 cable to connect ZINWELL Set-top Box and PC COM
port.
4.2 On PC side:
Launch Hyperterminal in MS Windows, and set the parameters as follow “115200-N-
8-N”. (It is in “Programs”-> “Accessories-> “Communication” -> “Hyperterminal” )
Enter the properties setting page:
8
Set the COM port
Press Configure Button to Configure
9
Setting the configure as following picture:
All settings are done. Press Call button to connect the Set-top box.
10
4.3 On Set-top box side:
Use OSD to upgrade s/w. Then you see “C C C C ...” shown on PC Hyperterminal
screen.
4.5 On PC side:
Enter Hyper terminal menu, “ Transfer” -> “Send file” -> “B OWSE”, and select new
software file (set protocol in 1K Xmodem)-> press “Send”
Ps. Set-top-box will wait PC to transmit the s/w. If you doesn’t send file to box, it will
timeout then exit the upgrade status. You should redo these actions again.
“Transfer” -> “Send file” -> “B OWSE”, and select new software file (set protocol in
1K Xmodem)-> press “Send”
6. When s/w update completed, the box will shut down automatically.
7. Restart box, it will boot up with new so tware.
Altri manuali per DVR7100/75
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Philips Registratore vocale
Philips
Philips LFH0898/00 Manuale utente
Philips
Philips VTR8060 Manuale utente
Philips
Philips LFH 9370/00 Manuale utente
Philips
Philips DPM8000 Guida
Philips
Philips DVDR5570H Manuale utente
Philips
Philips SPEECHMIKE AIR LFH3005 Manuale utente
Philips
Philips LFH0620 Manuale utente
Philips
Philips DPM 9450 Manuale utente
Philips
Philips VTR5500 Manuale utente
Philips
Philips Voice Tracer LFH0888 Manuale utente
Philips
Philips LFH0655/00 Manuale utente
Philips
Philips VOICE TRACER DVT1150 Manuale utente
Philips
Philips Pocket Memo LFH9380/27 Manuale utente
Philips
Philips Pocket Memo Digital Recorder Manuale utente
Philips
Philips VoiceTracer VTR8600 Manuale utente
Philips
Philips VideoTracer DVT3120 Manuale utente
Philips
Philips LFH9398/00 Manuale utente
Philips
Philips GoSure ADR800sp Manuale utente
Philips
Philips LFH9375/00 Manuale utente
Philips
Philips LFH9380 Manuale utente
