PICOTE Smart Spider DN150/6" Manuale di istruzioni
I
N
S
T
R
U
C
T
I
O
N
S
Operating & Safety Manual
Smart Cutter DN150-DN225 / 6”-9” & DN250-DN300/ 10”-12”
for 18mm/¾” Shaft
These instrucons are for your personal safety. Always ensure that you
have read and understood these instrucons before using any tools of
the Smart Cuer range. Please also read and understand the Maxi Miller
Power Plus manual before using the Smart Cuer Tool.
We now have resellers in the U.S., Europe & Australasia.
Locate your reseller at picotesolutions.com
2
TOPIC PAGE/S
SAFETY INFORMATION & SYMBOLS 3
AVAILABLE SIZES & POWER SOURCES 6
BILL OF MATERIALS 7
ASSEMBLY 12
USING THE SMART CUTTER 20
MAINTENANCE & SPARE PARTS 22
PRACTICAL TIPS & SAFETY ADVICE 24
WARRANTY POLICY & PROCEDURE 25
To watch practical demonstration videos, or to download an electronic copy of these in-
structions, please visit www.picotesolutions.com. Please note that videos are not intend-
ed as a replacement or alternative to this operating and safety manual, but only as an
additional learning tool.
TABLE OF CONTENTS
3
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
SAFETY INFORMATION
This section contains important safety information. Failure to
comply could result in serious injury or death.
Safety Symbols
Personal Protective Equipment (PPE)
Always use Personal Protective Equipment when using the Smart Cutter and Miller sys-
tems, including suitable overalls / protective clothing & footwear and the following:
Always wear suitable eye protection when using the Smart Cutter to prevent
sewage, chemicals or dust from irritating your eyes.
Always wear suitable ear protection when using the Smart Cutter and Miller
systems to prevent any hearing loss.
Always wear suitable cut-resistant gloves when using the Smart Cutter to pre-
vent any hand injuries. Any open injuries or skin irritations should be covered
at all times to avoid contact with sewage, chemicals or dust.
Always wear a suitable ventilation mask when using the Smart Cutter or Miller sys-
tems to prevent any resin dust being inhaled or consumed, which can cause occu-
pational asthma or dermatitis as well as eye irritation.
Danger risk of serious injury from rotating parts
Danger risk of serious injury, follow instructions
Danger risk of serious injury or death by electrocution, follow instructions
Danger risk of serious injury from hot parts
Safety symbols are used throughout this manual to draw attention to potential hazards.
Danger do not touch. Risk of injury, follow instructions
Danger risk of serious injury or death by electrocution, follow instructions
4
Dust produced can be dangerous to your health, inflammable or explosive.
Make sure the drain pipe has been opened and ventilated to stop any gases
forming in the lateral drain where the work takes place.
Before assembly, use, replacement of parts or maintenance, unplug the Picote
milling machine or your hand drill from its power socket.
High voltage. Failure to comply may lead to serious injury in-
cluding electric shock or injury from rotating parts!
Always remember
Safety Symbols cont.
Safety symbols are used throughout this manual to draw attention to potential hazards.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
ELECTRICAL SET UP REQUIREMENTS FOR MAXI MILLER POWER PLUS
Electrical shock can cause serious or fatal injury. Only qualified personnel
should install, maintain or troubleshoot this equipment.
Picote recommends that a properly trained electrician be available to wire a
power distribution box to whatever power source is available. In the case
where a generator is required, a minimum power requirement of 25,000
KW/KVA 3 Phase 480 volt is necessary.
The Power Plus is a dual voltage 3 phase power configuration. It uses a 10 gauge 4
wire cord.
Be sure the system is properly grounded/earthed before applying power. Do not apply power be-
fore you ensure that grounds are connected. Electrical shock can cause serious or fatal injury.
Follow the National Electrical Code (NEC) and local codes for the safe installation of the equip-
ment.
Do not operate the Power Plus Miller until you are sure that you are completely familiar with the
safe operation of the machine, all accessories and safety equipment. Improper use can lead to
severe injury. The user manual defines proper use of this equipment.
Contact Picote if you do not understand any procedure or operation concerning this
equipment or the user manual.
READ THE MAXI MILLER POWER+ MANUAL BEFORE USE
5
AVAILABLE SIZES & POWER SOURCES
The Smart Cutter is a fine tuning tool. It can be used to fine tune remaining edges after a
connection has been reinstated using the Twister tools. The Smart Cutter can also be
used to remove any remaining lining or inconsistencies, after the collapsed lining has
been removed using a Smart Crusher, Sweeper or Chains. The side grinding panels adapt
to the pipe size when the tool rotates. A Drill Head can be used if needed.
Selecting the correct Smart Cutter for the job
Choose your Smart Cutter according to the size of the original host pipe.
SMART CUTTER Shaft size
mm/inches
BEND 90° BEND 45°
Smart Cutter DN100 / 4” 18 / ¾”YES YES
Smart Cutter DN150 / 6” 18 / ¾”YES YES
Smart Cutter DN200-DN300 /
8”-12”
18 / ¾”YES YES
CHOOSING YOUR POWER SOURCE
The Smart Cutter for the 18mm/¾” diameter shaft has been designed for and can ONLY
be operated with the Picote Maxi Miller Power+ machine.
The machine should only be connected only to a 380-480 Volt (3-phase) power supp-
ly. The power source has to be grounded (earthed).
CHOOSING YOUR DRILL HEAD
The Smart Cutter can be used with or without the Drill or Crusher Heads by adding a Hub
Disc. The Drill Head and the Crusher are used when removing a deformed or collapsed
lining.
If access is restricted due to the failed or collapsed lining, the Smart Cutter might not fit
in with the Drill Head attached. In this case, the Drill Head may be replaced with a Hub
Disc. Without the Drill Head all the force is applied to the side grinding panels. The side
grinding panels will remove the remaining lining from pipe walls as required
6
BILL OF MATERIALS: Smart Cutter DN100/4”
The Hub Disc can be changed with the Crusher or Drill Head.
7
BILL OF MATERIALS: Smart Cutter DN150/6”
The Hub Disc can be changed with the Crusher or Drill Head.
8
BILL OF MATERIALS: Smart Cutter DN200-DN225/8”-9”
The Hub Disc can be changed with the Crusher or Drill Head.
Side grinding panels can be changed to 150x250 for DN250-DN300 pipes.
9
BILL OF MATERIALS - DN150/6” Smart Crusher Head
10
BILL OF MATERIALS - DN200/8” Drill Head
Altri manuali per Smart Spider DN150/6"
2
Questo manuale è adatto per i seguenti modelli
3
Indice
