Pilot Communications EV Lite Manuale utente

Pilot EV Lite

Quick Installation

Guide

17/01/2020 / DC1 / Version2

Tools required

# Name Remark

1Philips screwdriver Electric with bit preferred

2Hex (M4) screwdriver Electric with bit preferred

3Level –

4Stainless steel anchors Size M10

5Stainless steel bolts M10 to t the anchors

6Drill –

732A Type C Circuit Breaker –

85 core 6mm2 cable Length as required

9Pencil –

2 +44 (0) 1606 59 66 22

17/01/2020 / DC1 / Version2

Prerequisites

• This type of installation requires an electrical background.

• When unpacking the contents of the kit, it is crucial to perform a

visual check to confirm that none of the parts are damaged or

broken.

• Prior to installation, make sure to disconnect the main circuit

breaker (CB).

• Locate the serial number (S/N) on the attached test report and

confirm that the same serial number is configured in the

Chargepoint management system with the Certified Pilot EV

team.

Figure 1 S/N Sticker sample

This type of installation requires an electrical background.

When unpacking the contents of the kit, it is crucial to perform a visual check to

conrm that none of the parts are damaged or broken.

Prior to installation, make sure to disconnect the main circuit breaker (CB).

Locate the serial number (S/N) on the attached test report and conrm that the same

serial number is congured in the Chargepoint management system with the

Certied Pilot EV team.

Prerequisites

www.thepilotgroup.co.uk

17/01/2020 / DC1 / Version2

Make sure to always follow your local electrical regulations.

The Pilot EV Lite installation should only be carried out by a certied installer.

The below instructions are a guideline and provided for reference only. You are solely

responsible for following all applicable electrical safety procedures, codes, methods,

and materials provided as per the instructions below.

Prior to installation, make sure to disconnect the main circuit breaker (CB).

Carry out a visual inspection to verify that none of the parts are damaged.

Prerequisites

There is risk of re or electric shock. Do not alter, relocate, drill or remove any

component without consulting with the Pilot EV certied team.

Pilot EV is and will not be liable for any modications or results of such modications

done to the product during or after installation.

Installation must be carried out in dry conditions only.

Ensure that all power is turned o using a voltmeter or an equivalent device before

performing any installation.

ATTENTION

WARNING

CAUTION

4 +44 (0) 1606 59 66 22

17/01/2020 / DC1 / Version2

Place the wall mount on the

designated wall.

It is recommended to use a level

to ensure that the template is

aligned straight.

Mark the holes with pencil.

Mark the mount location1

1Mark the mount location

2DDrill holes

Place the wall mount on the

designated wall.

It is recommended to use a

level to ensure that the

template is aligned straight.

Mark the holes with pencil.

Using a drill make the holes

prior to installation.

Confirm that the hole

and anchor size are identical.

Using a drill make the holes prior

to installation.

Conrm that the hole

and anchor size are identical.

Drill holes

1Mark the mount location

2DDrill holes

Place the wall mount on the

designated wall.

It is recommended to use a

level to ensure that the

template is aligned straight.

Mark the holes with pencil.

Using a drill make the holes

prior to installation.

Confirm that the hole

and anchor size are identical.

www.thepilotgroup.co.uk

17/01/2020 / DC1 / Version2

Insert appropriate screw anchors

into the hole, ensuring that they t

the bolt size and wall type.

Install screw anchors3

Attach the bracket by application

of bolts.

Install the bracket4

6 +44 (0) 1606 59 66 22

17/01/2020 / DC1 / Version2

Using the Hex screwdriver, unfasten six screws (three from each side)

to dismantle the front panel.

Dismantle the front panel5

www.thepilotgroup.co.uk

17/01/2020 / DC1 / Version2

Dismantle the cable cover

Insert the cable

Using the Philips screwdriver,

unfasten the two screws to

dismantle the cable cover.

Insert the cable through the left

hole and use the keystone cable

clamp to secure it.

8 +44 (0) 1606 59 66 22

17/01/2020 / DC1 / Version2

Connect the cables according to the diagram:

L = Brown

N = Blue

PE Earth \ PE \ Ground = Yellow Green

Make sure to perform the appropriate PE connection test based on

the current edition of the IET Wiring regulations.

Connect the cable8

www.thepilotgroup.co.uk

17/01/2020 / DC1 / Version2

Using the Hex screwdriver, fasten the six screws (three from each side)

to assemble the front panel.

Assemble the front panel9

10  +44 (0) 1606 59 66 22

Indice

Altri manuali Pilot Communications Accessori per automobili

Pilot Communications

Pilot Communications EV Plus+ Manuale utente

Manuali Accessori per automobili popolari di altre marche

James Baroud

James Baroud Odyssey Manuale utente

Motorola

Motorola i50sx Manuale utente

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuale utente

Feniex

Feniex T3 Manuale utente

Renault

Renault 77 11 423 180 Manuale utente

Kia

Kia E8300-4D000 Manuale utente

Brink

Brink 756843 Manuale utente

Whispbar

Whispbar K085W Manuale utente

v.link

v.link CI-VL2-PC-HSD Manuale utente

Viking

Viking Stack-Rack Guida rapida alla configurazione

Aries

Aries 203015 Manuale utente

Choetech

Choetech AT0005 Manuale utente

ZZ2

ZZ2 ZZAIR-PRO Manuale utente

Holman

Holman 4A80L Manuale utente

Thule

Thule 2075 Manuale utente

Motorola

Motorola T325 Manuale utente

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guida all'installazione

DV8

DV8 FBJL-02 Manuale utente