Pirate C Series Manuale utente

User’s Manual

Read Manual

Failure to read, understand &

follow all safety and operation

procedures in this manual can

cause serious injury or death.

Manuals that are lost,

incomplete, or damaged must

be replaced immediately.

Manual P/N: PB-MAC002

Abrasive blasting can create dust that may contain

toxic materials from abrasive material and the

surface being blasted. NEVER use abrasives

containing high amounts of crystalline silica

including silica sand/beach sand for abrasive

blasting. Airborne crystalline silica causes silicosis,

a fatal respiratory disease. Abrasive blasting can

create high levels of noise that may cause hearing

damage. Always use proper safety equipment

including respiratory protection, hearing protection,

and comply with local, regional and national safety

codes. Ensure all operators of the equipment are

properly trained and everyone in the area including

bystanders are protected from the hazards of

abrasive blasting. The manufacturer, wholesaler

and distributor assume no responsibility arising

from the failure to comply with this warning.

C-Series Jr - 0.5 / 1.0 Cu Ft Abrasive Blasters

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

Thank you for your purchase of a Pirate Brand® CPR Series Blaster. It is important to note that

all Pirate Brand® blasting equipment is designed to be safe when used properly, however, misuse of any

abrasive blasting equipment is dangerous and can result in the severe injury or death of the operator and

others in the vicinity of the blasting equipment. In order to protect yourself and those around you, read

and follow all sections of this manual & warning labels located on the blasting equipment.

Denition Of Terms Used In This Manual

Abrasive: A granular material used for blasting the surface of an object. Also referred to as “Media.”

Blow-down: The automatic or manual release of air from a pressurized vessel. Also referred to as “Depressurize.”

Control Handle: A required device that allows the blaster to be remotely started and stopped.

Depressurize: The automatic or manual release of air from a pressurized vessel. Also known as “Blow-down”.

Pressure Hold System: Any blasting system in which the Pressure Vessel remains pressurized when the control

handle is released. Also known as a Manual Blow-down System.

Pressure Release System: Any blasting system in which the Pressure Vessel is automatically depressurized when

the control handle is released. Also known as an Automatic Blow-down System.

Pressure Vessel: The enclosed area of the blaster in which abrasive is contained and lled with pressurized air when

blasting.

Pressurize: To ll the pressure vessel with compressed air.

Properly Trained: A person who can be considered “properly trained” must have successfully completed a

sandblasting training course that focuses on the safe operation of stationary or portable abrasive blasters in the 0.5 -

6.0 cu. ft. capacity range. They must also have read and understood this manual in its entirety.

Silica: A hazardous substance which is contained in many naturally occurring abrasives. Dust produced by blasting

with abrasives containing silica can cause respiratory disease. Do not use abrasive containing silica under any

circumstance, even when respiratory protective equipment is being used.

Safety Symbols

The safety symbols shown below exist for the safety and protection of the operator and those in the

vicinity of the Abrasive Blaster. The descriptions below explain how they are used in relation to the

blasting equipment.

WARNING: This symbol calls attention to a

potentially hazardous situation that could result

in serious injury or death if the instructions

associated with the symbol are not followed. The

warning triangle will be displayed throughout the

manual to denote instructions to which special

attention should be paid.

DANGER: This symbol calls attention to a

potentially hazardous situation that WILL result

in serious injury or death if the instructions

associated with the symbol are not followed. The

warning triangle will be displayed throughout the

manual to denote instructions to which special

attention should be paid.

OR OR

Using This Manual

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

• All persons who will be operating or will be in the vicinity of the Abrasive Blaster during its

operation must receive proper training on how to safely operate the equipment and be informed

of the potential hazards involved. In addition to proper training, all persons who will be operating

or will be in the vicinity of the Abrasive Blaster during its operation must read, understand and

follow all procedures described in the user’s manual. For replacement manuals, please contact

your distributor or visit www.pirate-brand.com.

• Respiratory protection is mandatory for all persons operating or located in the vicinity of the

Abrasive Blaster. Follow all OSHA and NIOSH requirements for breathing equipment and

supplied air standards.

• Pressurized Vessels contain large amounts of stored energy and can cause severe injury or

death if safety procedures are not followed. Never perform maintenance or attempt to open

a Pressure Vessel for any reason while it is Pressurized. Always Depressurize and properly

disconnect equipment from its air source before performing any maintenance. Do not modify,

grind or weld on the pressure vessel for any reason. Doing so will void the ASME certification.

Do not use damaged pressure vessels.

• The use of proper remote control systems (commonly referred to as Deadman controls) are

required when using abrasive blasters. Never operate the Abrasive Blaster without remote

controls.

• All persons who will be operating or will be in the vicinity of the Abrasive Blaster during its

operation must protect themselves with the proper safety equipment and use of common sense.

Safety equipment including but not limited to Hearing, Eye, Body and Lung protection are

required. Abrasive blasters and the objects being blasted can be heavy and can lead to severe

injury or death if they fall over. Always follow all safety requirements of OSHA and NIOSH.

• Use only Genuine Pirate Brand® replacement parts when performing maintenance on the

Abrasive Blaster. Do not modify the equipment for any reason. Use of modified or non-Pirate

Brand® parts can cause an unsafe situation and will void your warranty.

• Never use malfunctioning or damaged equipment. Before each use, inspect the Abrasive

Blaster for proper function.

• Supply only cool, dry, compressed air that is free of debris to the Abrasive Blaster. Moisture

or debris that reaches the remote control system can cause an unsafe situation. Do not supply

compressed air to the blaster that exceeds 150 psi.

• Do not use abrasive blasters in areas that could be considered a hazardous location as

described in the National Electric Code NFPA 70, Article 500. Never use the Abrasive Blaster in

wet environments. Always connect electrically controlled abrasive blasters to a Ground Fault

Circuit Interrupter (GFCI).

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

Using This Manual

Denition Of Terms

Safety Symbols

WARNINGS

Safety Label Information

How CPR Systems Work

OPERATING PROCEDURES

Set-Up 8

Before You Blast 9

Blasting 10

MAINTENANCE PROCEDURES

TROUBLESHOOTING

Warranty

Pressure Vessel Parts Lists

Pipe String Parts Lists

Pneumatic Controls 18

Electric Controls 20

Valve Parts Lists

Control Handle Parts Lists

Blasting Set-Up

Available Accessories

Blasting Chart

. . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . .

. . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . .

Distributed By: Contact Info:

For manual updates visit the

Pirate Brand® website at:

www.pirate-brand.com

Table Of Contents

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

1 - Explosion Hazard (X2)

2 - Severing Hazard (X2)

3 - Read Manual

4 - Crush Hazard

5 - Exhaust Hazard

6 - Breathing Hazard

7 - Hearing Hazard

8 - Eye Hazard

9 - Pressurized Hose

10 - Spray Hazard

11 - WARNING Label

12 - Pirate Brand® Leg Label

13 - CPR Series Label

14 - Inlet Label

15 - Outlet Label

16 - 12VDC Label

17 - Pirate Brand® Label

Instructions For Installing Replacement Label Pack

1. Completely remove old label and clean area thoroughly before applying new label.

2. Apply replacement labels in locations as described above or as close as possible if area is obstructed

3. 12 VDC Label (#16) is only to be used on electric remote controlled systems. DO NOT apply label to systems with pneumatic remote

controls.

Labels must be replaced when they are no longer readable!

Replacement Label Pack P/N: PB-LPC002

Warning Label Locations

CPR SERIES

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

WARNING: This section of the manual is designed to give you a general understanding of how the

Abrasive Blaster functions. All sections of this manual must be read and understood before

operating the equipment.

Flow of Compressed Air

Flow of Abrasive

Flow of Exhaust Air

During Blow-down

ADDING ABRASIVE

Abrasive is added through the hole in the top of the Abrasive Blaster where the Pop-up and its seat are

located. When abrasive is added, it ows down through the hole, around the Pop-up, and down to the

bottom of the pressure vessel where it will exit through the Metering Valve when blasting is started.

PRESSURIZATION

When a compressed air source (such as an air-compressor) is connected to the inlet of the Abrasive

Blaster and the Inlet Shut-O󰀨 Valve is opened, compressed air ows to the Inlet Valve where it is stopped.

When the control handle is activated, the Inlet Valve opens and air ows into the Pressure Vessel causing

the Pop-up (located internally) to seal against its seat. Simultaneously, the Diaphragm Valve closes

sealing the Pressure Vessel allowing it to hold pressure. Air will also continue past the Choke Valve,

through the Pusher Line, and nally to the “tee” under the Metering Valve where it is mixed with abrasive.

The mixture of compressed air and abrasive will now exit the Abrasive Blaster through a blast hose and

nozzle connected to the coupling under the Metering Valve and blasting begins. It is important to note

that, some abrasive will collect at the base of the Metering Valve causing the blast hose to pulsate and

spray abrasive erratically for a short time while pressure builds up in the pressure vessel. This is normal

and will not damage the Abrasive Blaster.

DEPRESSURIZATION (BLOW-DOWN)

When the control handle is released in a pressure release (CPR) system, the Inlet Valve automatically

closes stopping the ow of compressed air into the Pressure Vessel. Simultaneously, the Diaphragm

Valve opens allowing the compressed air in the pressure vessel to exit the Abrasive Blaster through the

Diaphragm Valve. When all the pressure in the Pressure Vessel is released, blasting stops.

How CPR Systems Work

(Pressure Release)

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

Some items moved or rotated for clarity.

Exhausted

Air

Compressed

Air Inlet

Air / Abrasive Mix

To Blasting Nozzle

Loaded Abrasive

Inlet

Valve Inlet

Shut-Off

Valve

Choke

Valve

Metering

Valve

Pressure

Vessel

Diaphragm

Valve

Pop-up

Pusher

Line

How CPR Systems Work

(Pressure Release)

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

WARNING: The Procedures provided in the Operating Procedures section of the manual are designed to

provide basic information on how to safely operate the features of Pirate Brand® CPR Series Abrasive

Blasters. Only personnel thoroughly trained in abrasive blasting should operate the Abrasive Blaster.

INSPECT PRESSURE VESSEL

When you receive your Abrasive Blaster, remove the

Handway Assembly and check for foreign items that may

have fallen into the Abrasive Blaster through the Pop-up

opening. Remove any foreign materials and reinstall the

Handway Assembly.

DANGER: Never perform any maintenance or

attempt to open the Abrasive Blaster in any way

while it is pressurized. The violent release of

compressed air and propelled objects will cause

serious injury or death.

RE-TIGHTEN HANDWAY ASSEMBLY

After the Abrasive Blaster has been pressurized for the rst

time, tighten the nut on the Handway Assembly. Tightening

the nut on the Handway Assembly should also be done any

time after the handway has been removed for maintenance

before and after the next pressurization.

DANGER: Never perform any maintenance or

attempt to open the Abrasive Blaster in any way

while it is pressurized. The violent release of

compressed air and propelled objects will cause

serious injury or death.

PURGE AIR SUPPLY HOSE

Before connecting the Air Supply Hose to the Abrasive

Blaster, purge the hose of any moisture or foreign debris.

Standing water or moisture in the air line will cause

degraded performance of the Abrasive Blaster. Air supplied

to the Abrasive Blaster must be clean, dry and cool.

ATTACH REMOTE CONTROL HANDLE

Attach the Remote Control Handle to the Blast Hose near

the Nozzle with hose clamps or heavy wire ties. Form a loop

of Twinline/Control Cord that comes 6” away from the Blast

Hose, runs 6” parallel to the Blast Hose, and comes 6” back

to the Blast Hose. Using duct tape, attach the Twinline/

Control Cord to the Blast Hose where the loop ends by

wrapping the tape around the Twinline/Control Cord twice

and then around the Blast Hose. This creates a strain-relief

attachment and is only necessary on the rst connection

near the Control Handle. Starting from the Nozzle end of

the Blast Hose, attach the Twinline/Control Cord to the blast

hose by wrapping duct tape around both every 3 feet.

6”

See page 15 for

larger diagram

of blaster

components

Inlet

Valve

Inlet

Shut-Off

Valve

Choke

Valve

Metering

Valve

Pressure

Vessel

Diaphragm

Valve

Pop-up

Pusher

Line

Inlet Valve

Petcock

Nozzle

Blast

Hose

Control

Handle

Compressed

Air Supply

Hose

Operating Procedures

Setting-Up The Blaster

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

PRE-BLAST CHECK

Before each use of the Abrasive Blaster, it must be checked

to ensure it is in a safe condition to be used. Closely

examine all components of the Abrasive Blaster for signs

of excessive wear, worn out seals and hoses, or damaged

components. If any component of the Abrasive Blaster is

found to be damaged or worn, it must be replaced before

blasting.

WARNING: Never use an Abrasive Blaster if any

components are damaged or worn. Damaged or

worn parts must be replaced before use.

ADDING ABRASIVE

Before lling the Abrasive Blaster, make sure the Inlet Shut-

O󰀨 Valve is closed, the Inlet Valve Petcock is open, and

the pressure vessel is in a depressurized state. Abrasive

is added by pouring it into the top of the Abrasive Blaster

where it can ow around the Pop-up and into the pressure

vessel. Do not overll the Abrasive Blaster. Do not allow

foreign materials to enter the Abrasive Blaster. It is

recommended that a screen be used to prevent foreign

objects from entering the Abrasive Blaster.

DANGER: Never reach into the Pop-up opening

while lling the Abrasive Blaster. It can close

without warning causing severe injury or death.

WARNING: Pirate Brand® Abrasive Blasters may

not be used with abrasives containing silica.

Never use abrasives containing silica.

WARNING: Never ll the abrasive blaster with

the Inlet Shut-O󰀨 Valve in the open position.

Always close the Inlet Shut-O󰀨 Valve before

lling.

WARNING: Electrically conductive abrasives

may not be used with abrasive blasters using

Electric Remote Control Systems without

changing to sealed strain relief connectors.

WARNING: Never attempt to move or transport

the Abrasive Blaster when it contains Abrasive.

REMOTE CONTROL SYSTEM

Abrasive Blasters must use a Remote Control System

(commonly known as a deadman) to start and stop

abrasive blasting. Remote Control Systems can be electric

or pneumatic.

Electric: Connect the Remote Control Handle to the

Abrasive Blaster’s female twist-lock connector. Connect a

12 VDC power source (12V Battery or Optional 120 VAC to

12 VDC converter) to the Abrasive Blaster’s male twist-lock

connector.

Pneumatic: Connect the Remote Control twinline hose to

the Abrasive Blaster using the supplied threaded ttings.

It is not recommended that Pneumatic Remote Control

Systems are used when the Blast Hose length will be

longer than 100 feet.

WARNING: Never operate the Abrasive Blaster

without a Remote Control System.

DANGER: Always use caution around electric

sources to avoid electric shock. Do not operate

electrical remote controlled Abrasive Blasters in

wet or other hazardous environments

CONNECTING HOSES

Before connecting hoses to the Abrasive Blaster, make

sure the Inlet Shut-O󰀨 Valve is closed and the compressed

air supply is shut o󰀨. Connect the hose coming from the

compressed air supply to the inlet on the Abrasive Blaster

and secure with safety clips. Connect the blast hose to the

coupling by the Metering Valve at the base of the Abrasive

Blaster and secure with safety clips .

WARNING: Always use safety devices like clips

and whip-checks (safety cables) at hose

connections.

Operating Procedures

Before You Blast

C-Series Jr - 0.5 / 1.0 Cu Ft User’s Manual

PRESSURIZING THE ABRASIVE BLASTER

Before pressurizing the Abrasive Blaster make sure the

following conditions occur:

• All “BEFORE YOU BLAST” procedures have

been followed.

• The Inlet Shut-O󰀨 Valve is closed.

• The Inlet Valve Petcock is closed.

• The Remote Control Handle is released.

• All hose connections are secure and have a safety clip

installed.

• The Abrasive Blaster is set up in a safe and level location

where all people in the vicinity are aware of its presence.

• All necessary safety equipment is present and being

worn by all people in the vicinity of the Abrasive Blaster.

• Only personnel who have been thoroughly trained and

have read and understand the manual are in the vicinity

of the Abrasive Blaster

When these conditions are met, turn on the compressed air

source and open the Inlet Shut-O󰀨 Valve on the Abrasive

Blaster. The Abrasive Blaster is now ready to begin blasting.

DANGER: Never perform any maintenance or

attempt to open the Abrasive Blaster in any way

while it is pressurized. The violent release of

compressed air and propelled objects will cause

serious injury or death.

DANGER: Never supply compressed air

exceeding 150 PSI (10.3 BAR) to the Abrasive

Blaster.

WARNING: The Blast Hose may kick back when

Remote Control Handle is activated. Be

prepared and brace yourself for kick back.

Blast Hoses will normally kick back erratically for

a short time when the Abrasive Blaster is started.

WARNING: All those who will be in the area

while blasting is to occur must be properly

trained, read the manual, and wearing safety

equipment to protect from the hazards described

by the WARNING and DANGER labels located

on the Abrasive Blaster. If any labels are worn

or missing they must be replaced.

WARNING: 100 PSI Minimum. Failure to provide

a constant air supply of at least 100 PSI can

cause excessive wear to multiple components

and the control system to operate improperly.

USING THE ABRASIVE BLASTER

After pressurizing the Abrasive Blaster, it is ready to begin

blasting. Fold down safety ap lever lock and squeeze the

Remote Control Handle to start the ow of abrasive and

compressed air. Adjustments to the air/abrasive mixture

can be made by swinging the handle on the Metering

Valve. There will be a delay between a change made at

the Metering Valve and what comes out of the Nozzle

depending on the length of Blast Hose being used.

To stop the ow of compressed air and abrasive,

release the Remote Control Handle and blasting will stop

after a short time. How long it takes for blasting to stop

will depend on the length of Blast Hose being used. The

pressure vessel will automatically exhaust through the

Diaphragm Valve causing a rush of compressed air that

can propel any loose objects, debris or spilled abrasive at

nearby personnel. For this reason, personnel must not be

located near the Abrasive Blaster when blasting is taking

place.

DANGER: Airborne particles produced by

abrasive blasting can cause respiratory disease.

All persons operating or located near the blasting

site must wear approved NIOSH / OSHA

approved breathing equipment. Never use

abrasive containing silica.

DANGER: Never stand near an Abrasive Blaster

when it is in operation. The release of the

Remote Control handle will cause a sudden

release of compressed air from the Diaphragm

Valve without warning. Only Adjust the

Metering Valve after the Abrasive Blaster has

completely depressurized.

WARNING: Only personnel thoroughly trained in

abrasive blasting should operate the Abrasive

Blaster. This manual only provides basic

information on how to safely operate the features

of Pirate Brand® CPR Series Abrasive

Blasters.

WARNING: Never point the blast Nozzle at

yourself, other people, or the Abrasive Blaster.

WARNING: Never use the abrasive blaster

without a nozzle securely installed in the blast

hose nozzle holder

WARNING: The Choke Valve must be completely

open when blasting or damage to equipment will

occur.

Operating Procedures

Blasting

Altri manuali per C Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Pirate Utensili elettrici

Pirate

Pirate C Series Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale