Pit Boss Ultimate Griddle Series Manuale utente

300522

MODEL / MODÈLE / MODELO : PB2BGD2

PART / PIÈCE / PARTE : 10780, 10844

WARNING: PLEASE READ THE ENTIRE MANUAL BEFORE

INSTALLATION AND USE OF THIS GAS APPLIANCE.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD

RESULT IN PROPERTY DAMAGE, BODILY INJURY OR

EVEN DEATH. CONTACT LOCAL BUILDING OR FIRE

OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION

INSPECTION REQUIREMENTS IN YOUR AREA.

AVERTISSEMENT : VEUILLEZ LIRE L'INTÉGRALITÉ DU

MANUEL AVANT INSTALLATION ET UTILISATION DE CET

APPAREIL À GAZ. LE NON-RESPECT DE CES INSTRUCTIONS

PEUT ENTRAÎNER DES DOMMAGES MATÉRIELS, DES

DOMMAGES CORPORELS OU MÊME LA MORT. CONTACTEZ

LES AUTORITÉS LOCALES COMPÉTENTES CONCERNANT

LES RESTRICTIONS ET LES EXIGENCES D'INSPECTION EN

VIGUEUR DANS VOTRE RÉGION.

ADVERTENCIA: LEA TODO EL MANUAL ANTES DE

MONTAR Y USAR ESTA BARBACOA DE GAS. SI NO SE

SIGUEN ESTAS INSTRUCCIONES, PUEDEN PRODUCIRSE

DAÑOS MATERIALES, LESIONES CORPORALES O

INCLUSO LA MUERTE. PÓNGASE EN CONTACTO CON LOS

ADMINISTRADORES DEL EDIFICIO O CON LOS BOMBEROS

PARA CONSULTAR LAS RESTRICCIONES Y LOS REQUISITOS

DE INSPECCIÓN DE LAS INSTALACIONES DE SU ZONA.

 

 ' |   

2 

  

IMPORTANT, READ CAREFULLY, RETAIN

FOR FUTURE REFERENCE. MANUAL MUST

BE READ BEFORE OPERATING!

 

 2  

 

IMPORTANT, PRENEZ CONNAISSANCE DE

CE DOCUMENT ET CONSERVEZ-LE POUR

RÉFÉRENCE ULTÉRIEURE. VOUS DEVEZ LIRE

CE GUIDE AVANT D’UTILISER LE BARBECUE!

  2

  



IMPORTANTE, LEER DETENIDAMENTE,

CONSERVAR PARA REFERENCIA FUTURA.

LEA EL MANUAL ANTES DEL USO!

FOR OUTDOOR AND HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE. FUEL

AND ACCESSORIES NOT INCLUDED.

RÉSERVÉ À L’USAGE EXTÉRIEUR ET RÉSIDENTIEL UNIQUEMENT. NON DESTINÉ À

UN USAGE COMMERCIAL. COMBUSTIBLE ET ACCESSOIRES NON INCLUS.

SOLO PARA USO EN EXTERIORES Y EN EL HOGAR. NO ES PARA USO COMERCIAL.

NO INCLUYE COMBUSTIBLE NI ACCESORIOS

ENGLISH

may be copied, transmitted, transcribed, stored in a retrieval

system, in any form or by any means without expressed

written permission of,

Dansons

3411 North 5th Avenue, Suite 500, Phoenix, ,  85013

www.pitboss-grills.com

Customer Care

USA: (480) 923-9630

Canada (Toll-Free): 1-877-942-2246

  

Parts & Specs...................................................................... 3

Assembly Preparation......................................................4

Assembly Instructions

Connecting The Wheels To The Legs........................................4

Assembling The Cart Base.......................................................... 5

Mounting The Cart Panels..........................................................5

Securing The Cart Bars................................................................6

Mounting Gas Cylinder Supports .............................................6

Securing The Side Shelf Brackets..............................................6

Installing The Side Shelves......................................................... 7

Mounting The Extra Features.................................................... 7

Mounting The Lid Handle........................................................... 7

Securing The Lid Support ...........................................................8

Installing The Firebox To The Cart............................................8

Inserting The Hot Plate Screws.................................................8

Placing The Cooking Components............................................9

Installing The Ignition Battery..................................................9

ENGLISH

  

MODEL ASSEMBLED (WxDxH) WEIGHT COOKING AREA BTU/HR

 22 1,273   728   940 

/ 50.1   28.6   37.0  47.4 

/ 104.5  2,720 

/ 421.6  26,000

Part# Description

1 Firebox (x1)

2 Hot Plate (x1)

3 Hot Plate Leg Screws (x4)

4 Grease Cup (x1)

5 Lid Support (x1)

6 Lid Handle Bezel (x2)

7 Lid Handle (x1)

8 Cart Front Panel (x1)

9 Cart Back Panel (x1)

10 Cart Side Panel - Left (x1)

11 Cart Side Panel - Right (x1)

12 Side Shelf - Left (x1)

13 Side Shelf - Right (x1)

14 Gas Cylinder Wire Retainer (x1)

15 Gas Cylinder Support Bracket (x1)

16 Paper Towel Hook (x1)

17 Support Leg for Caster - Front (x1)

18 Support Leg for Caster - Back (x1)

19 Support Leg for Wheel - Front (x1)

20 Support Leg for Wheel - Back (x1)

21 Side Shelf Bracket - Left (x2)

22 Side Shelf Bracket - Right (x2)

23 Bottle Opener (x1)

24 Cart Bar A (x2)

25 Cart Bar B (x2)

26 Bottom Shelf (x1)

27 Locking Caster (x2)

28 Wheel (x2)

A Screw (x40)

B Screw (x4)

C Washer (x23)

D Locking Washer (x23)

E Screw (x4)

F Wheel Cotter Pin (x2)

G Wheel Washer (x2)

H Wheel Axle Pin (x2)

I Battery (x1)

NOTE: Due to ongoing product development, parts are subject to change without notice. Contact

Customer Care if parts are missing when assembling the unit.

  

  

  

16 12

ENGLISH

 

IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws

completely until all screws for that step have been installed. Hardware combination involving a locking washer and

washer should be installed with the locking washer closest to the head of the screw.

1.      

Parts Required:

1 x Support Leg for Caster / Front (#17)

1 x Support Leg for Caster / Back (#18)

1 x Support Leg for Wheel / Front (#19)

1 x Support Leg for Wheel / Back (#20)

2 x Locking Caster (#27)

2 x Wheel (#28)

2 x Wheel Cotter Pin (#F)

2 x Wheel Washer (#G)

2 x Wheel Axle Pin (#H)

Installation:

• Attach the Wheel to the Support Leg for Wheel by inserting the Wheel

Axle Pin through the Wheel, Support Leg hole, Wheel Washer, then

secure using the Wheel Cotter Pin. Repeat installation for the other

Support Leg with Wheel. Note illustration 1A.

• Install a Locking Caster Wheel to the bottom of a Support Leg by

hand-tightening into the hole. The Locking Caster Wheel is inserted

completely when it cannot rotate any further into the Support Leg.

Repeat installation for second Support Leg. Note illustration 1B.

 

Parts are located throughout the shipping carton, including underneath the griddle. Inspect the unit, parts, and hardware blister

pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the griddle

before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt

to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss® Grills Customer Care for parts.

www.pitboss-grills.com

IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.

Tools required for assembly: screwdriver and wrench.

Tools not included.

1

1







ENGLISH

2.    

Parts Required:

1 x Bottom Shelf (#26)

4 x Screw (#A)

4 x Washer (#C)

4 x Locking Washer (#D)

Installation:

• Place a piece of cardboard on the floor to prevent scratching the unit

and parts during assembly.

NOTE: Ensure the flat surface of the Bottom Shelf is facing up.

• Attach the Bottom Shelf to one Support Leg with Wheel by carefully

aligning it into the corner, then secure using one washer, locking washer,

and screw. Repeat installation for the other three Support Legs to the

remaining three corners of the Bottom Shelf. See illustration for proper

arrangement of the Support Legs.

IMPORTANT: There are three holes on the short side of the Bottom

Shelf. See proper positioning in illustration. If installed incorrectly,

the gas tank cannot be placed in future steps.

3.    

Parts Required:

1 x Cart Front Panel (#8)

1 x Cart Back Panel (#9)

1 x Cart Side Panel - Left (#10)

1 x Cart Side Panel - Right (#11)

16 x Screw (#A)

Installation:

• Install the Cart Front Panel between the front Support Legs of the Cart

Base. Secure using two screws into each Support Leg. Repeat same

installation for the Cart Back Panel. Note illustration 3A.

NOTE: Ensure the "PIT BOSS" of the Cart Front Panel is facing the

front of the unit. The flat surface of the Cart Back Panel should face

towards the back.

• Install the Cart Side Panel Left between the left Support Legs of the

Cart Base. Secure using two screws into each Support Leg. Repeat same

installation for the Cart Side Panel Right to the right Support Legs of the

Cart Base. Note illustration 3B.

IMPORTANT: The latches on the Cart Side Panels should face forward.

3

3

17 18









ENGLISH

4.    

Parts Required:

2 x Cart Bar A (#24)

2 x Cart Bar B (#25)

4 x Screw (#B)

4 x Washer (#C)

4 x Locking Washer (#D)

Installation:

• Secure Cart Bar A and Cart Bar B to each Support Leg, as shown, using

washer, locking washer, and screw.

5.    

Parts Required:

1 x Gas Cylinder Wire Retainer (#14)

1 x Gas Cylinder Support Bracket (#15)

3 x Screw (#A)

3 x Washer (#C)

3 x Locking Washer (#D)

Installation:

• Mount the Gas Cylinder Support Bracket to the Cart Bottom Shelf using

three washers, locking washers and screws. Note illustration 5A.

• Install the Gas Cylinder Wire Retainer between the Support Legs on the

right side of the unit. Insert the hooked end first, then secure by aligning

the other end into the keyhole. Note illustration 5B.

6.     

Parts Required:

2 x Side Shelf Bracket - Left (#21)

2 x Side Shelf Bracket - Right (#22)

12 x Screw (#A)

12 x Washer (#C)

12 x Locking Washer (#D)

Installation:

• Mount one Side Shelf Bracket to a Support Leg using three washers,

locking washers and screws. Install each screw halfway first, then

tighten completely when all three screws are mounted and aligned

properly. Repeat installation for the other three Side Shelf Brackets to

the remaining three Support Legs.

5

5













ENGLISH

7.    

Parts Required:

1 x Side Shelf - Left (#12)

1 x Side Shelf - Right (#13)

4 x Screw (#E)

Installation:

• Align and position one Side Shelf on the Side Shelf Brackets on one side

of the unit. From underneath, secure a screw into each corner, as shown

in illustration. Repeat same installation for the Side Shelf on the other

side of the unit.

NOTE: Once installed, both Side Shelves can be raised (for use) or

lowered (for storage) with ease.

IMPORTANT: Avoid using the Side Shelves to move or lift the unit.

The weight of the unit will cause the shelves to break, which is not

covered by warranty.

8.    

Parts Required:

1 x Paper Towel Hook (#16)

1 x Bottle Opener (#23)

2 x Screw (#A)

Installation:

• Mount the Bottom Opener to the Front-Left Support Leg using two

screws. Note illustration for correct orientation, with opening angled

downwards.

• Install the Paper Towel Hook on the two pre-mounted screws of the

same Support Leg. Press down to ensure the Paper Towel Hook stays

secure in place.

9.    

Parts Required:

1 x Firebox (#1)

2 x Lid Handle Bezel (#6)

1 x Lid Handle (#7)

Installation:

• Remove the pre-installed screws from the Lid Handle. From inside the

lid of the Firebox, insert one screw to protrude to the outside. Add a

Lid Handle Bezel on the screw, then hand-tighten the screw (from the

inside) into the Lid Handle. Repeat same installation for other end of Lid

Handle.





ENGLISH

10.    

Parts Required:

1 x Lid Support (#5)

3 x Screw (#A)

Installation:

• On the backside of the Firebox, fasten the Lid Support to the center of

the panel using three screws.

11.      

Installation:

• Place the Firebox next to the Cart, both facing the same direction. Using

two people, lift the Firebox using the inset grooves on each side. Slowly,

place the Firebox onto the cart frame, passing the regulator and hosing

through the Cart side Panel on the right of the unit. Note illustration 11A.

IMPORTANT: Take care to avoid pinching or damaging the regulator

or hosing during installation of the Firebox to the Cart. Poor

installation may cause the parts to not function properly.

• Once in position, turn the latches (one on each side) to lock the Firebox

into the Cart. Note illustration 11B.

12.     

Parts Required:

1 x Hot Plate (#2)

4 x Hot Plate Screws (#3)

Installation:

• Turn the Hot Plate upside-down. Insert a Hot Plate Screw into a corner

hole of the Hot Plate, turning by hand, until it cannot rotate any further

into the nut. Repeat same installation on the other three corner holes.

11

11



12 3

ENGLISH

13.    

Parts Required:

1 x Grease Cup (#4)

Installation:

• Open the Firebox lid. Carefully, place the Hot Plate into the Firebox. Once

the Hot Plate is installed, ensure it sits level in the Firebox. Adjust the

height of the Hot Plate Screws, if needed, so the Hot Plate is level.

NOTE: To maintain the searing and grilling performance of your Hot

Plate, regular care and maintenance is required.

• Place the Grease Cup into the Grease Cup housing on the front of the

Firebox, as shown in the illustration.

14.    

Parts Required:

1 x Battery (#I)

Installation:

• Turn the ignition button cap counter-clockwise to remove it. Insert the

Battery into the housing with the positive (+) terminal facing outward.

Screw the ignition button cap back into place to cover.

• The unit is now completely assembled.



FRANÇAIS

AVIS SUR LES DROITS D’AUTEUR

manuel ne peut être reproduite, transmises, transcrite ou

stockée dans un système de recherche de quelque façon que ce

soit sans l’autorisation préalable écrite de,

Dansons

3411 North 5th Avenue, Suite 500, Phoenix, ,  85013

www.pitboss-grills.com

Service à la clientèle

États-Unis: (480) 923-9630

Canada (Toll-Free): 1-877-942-2246

  

Pièces et spécifications .................................................. 11

Préparation de l’assemblage.........................................12

Instructions d’assemblage

Connexion des roues aux pieds................................................12

Montage de la base du chariot................................................13

Montage des panneaux du chariot.........................................13

Fixation des barres du chariot ................................................ 14

Montage des supports à bouteille de gaz ........................... 14

Fixation des supports de tablette latérale........................... 14

Installation des tablettes latérales.........................................15

Montage des éléments supplémentaires..............................15

Montage de la poignée du couvercle.....................................15

Fixation du support du couvercle........................................... 16

Installation du foyer dans le chariot ..................................... 16

Insertion des vis de la plaque chauffante............................ 16

Mise en place des éléments de cuisson .................................17

Installation de la batterie d'allumage....................................17

Altri manuali per Ultimate Griddle Series

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Pit Boss Piastra

Pit Boss

Pit Boss PB2BGD2, PB3BGD2, PB4BGD2, PB5BGD2 Manuale utente

Pit Boss

Pit Boss Ultimate Griddle PB3BGD2 Manuale utente

Pit Boss

Pit Boss PB336GS Manuale utente

Pit Boss

Pit Boss PB757GS Manuale utente

Pit Boss

Pit Boss Ultimate Griddle PB5BGD2 Manuale utente

Pit Boss

Pit Boss Ultimate Griddle Series Manuale utente

Pit Boss

Pit Boss PB4BGS1 Manuale utente

Pit Boss

Pit Boss PB5BGD Manuale utente

Pit Boss

Pit Boss PB757GS Manuale utente

Pit Boss

Pit Boss 757GS Series Istruzioni per l'installazione

Pit Boss

Pit Boss PB5BGD Manuale utente

Pit Boss

Pit Boss Ultimate Griddle PB2BGD2 Manuale utente

Pit Boss

Pit Boss Sportsman PB2BSPD Manuale utente

Pit Boss

Pit Boss 336GS Istruzioni per l'installazione

Pit Boss

Pit Boss PB2BGT1 Manuale

Pit Boss

Pit Boss 200GS Istruzioni per l'installazione

Pit Boss

Pit Boss PB2BGT1 Istruzioni per l'installazione

Pit Boss

Pit Boss Ultimate Griddle PB2BGD2 Manuale utente

Manuali Piastra popolari di altre marche

Proctor-Silex

Proctor-Silex 25340 Manuale utente

New House Kitchen

New House Kitchen NH33-C Manuale utente

Magikitch'n

Magikitch'n 24 Manuale utente

Black Stone

Black Stone 1650 Manuale utente

Anvil

Anvil FTA7116 Manuale utente

Presto

Presto 07030 Manuale utente

Dyna-Glo

Dyna-Glo DGL260SNP Manuale utente

Char-Broil

Char-Broil 19952085 Manuale utente

APW Wyott

APW Wyott HMG-2424 Manuale utente

Airxcel

Airxcel Suburban Elite SOP-1005A Manuale utente

Keating Of Chicago

Keating Of Chicago MIRACLEAN PRE-2000 Manuale utente

Nexgrill

Nexgrill 720-0786A Manuale utente

Outwell

Outwell FH-3047C Manuale utente

Rankam

Rankam Member's Mark GR2298901-MM-02 Guida di riferimento rapido

Black Stone

Black Stone 1972 Manuale utente

Star

Star Ultra Max 760TA Manuale utente

NuWave

NuWave Precision Cast Iron Griddle Manuale operativo

BERJAYA

BERJAYA EG 1750 Manuale utente