Pivot SHUTTLE Manuale utente

www.pivotcycles.com 1.877.857.4868

PIVOT SHUTTLE

Owner's Manual

Performance. Redened.

This manual is intended to provide you with the information

needed to get you on the trail.This guide will walk you through the

steps necessary to set up all the components and become familiar

with the Shimano STEPS E8000 System. This document contains

some helpful diagrams and reference material to make sure you

have everything necessary to maintain your Shuttle and enjoy it to

the fullest.

www.pivotcycles.com 1.877.857.4868

Table of Contents

Performance. Redened.

SECTION PAGE

1. Quick Start Guide 1

- Bike Set-up 1

- Charging the Battery 1

- Powering the System ON and OFF 1

- Assist Mode Operation 1

2. Basic Operation 2

- Assist and Shifter Switch Function 2

- Operating the Cycle Computer 2

- Screen Display 2

3. Bike Set-up 3

- Setting Proper Sag 3

- Setting Compression Damping on the Fox DPX2 3

- Setting Open Mode Adjust on the Fox DPX2 3

- Setting Rebound Damping on the Fox DPX2 4

- Setting Air Pressure on the Fox 36 Fork 4

- Setting Compression Damping on the Fox 36 Fork 5

- Setting Rebound Damping on the Fox 36 Fork 5

- Recommended Tire Pressure 5

- Adjusting Saddle Height 5

4. Shimano STEPS E8000 System 6

- Connecting to E-Tube Project 6

- Main Menu for E-Tube Project 6

- Customize Menu in E-Tube Project 7

- Update Firmware Menu in E-Tube Project 7

- Preset Menu in E-Tube Project 7

- Battery Charging Notes 8

- Charger LED Lamp 8

- Battery Power Panel LED Lamps 8

- Removing the Battery 9

- Installing the Battery 9

5. Troubleshooting 10

- Cycle Computer Warning Codes 10

- Cycle Computer Error Codes 10

- Battery LED Warning Codes 11

6. Schematics 12

- Shimano STEPS E8000 Schematic 12

- Small Parts Schematic 13

- Small Parts Table 14

- Wiring Diagram 15

7. Reference Material 16

- Shimano STEPS E8000 System 16

- Pivot Shuttle 16

www.pivotcycles.com 1.877.857.4868

QUICK START GUIDE

Bike Set-up

• Before riding, reference the chart below as a rough guide on how to set the bike's components.

This "Quick Start Guide" provides the essential information to set up your bike. For detailed information

about the Shimano STEPS E8000 System and bike set up, please refer to the full owner's manual.

Adjusting Saddle Height

• The seat post collar on the Shuttle can be loosened and tightened with a 4mm hex wrench.

• Before raising or lowering the seat height, using a 2mm hex wrench, loosen the head tube cable port

securing the dropper post housing. Be sure to re-tighten the cable clamp after adjusting the saddle height.

Charging the Battery

• The battery does not come charged and must be charged completely before the rst use.

• The charging port is located on the non-driveside of the downtube near the bottom of the battery.

• The battery has a sealing cover (g. 1) that needs to be removed for charging.

• The charging cable (g. 2) is plugged into the battery through the charging window in the frame. The

battery can also be charged o the bike. For battery removal instructions, see the full owner's manual.

• Make sure the the charger is securely attached. To verify that the bike is charging, the light on the charger

will illuminate and lights on the battery power panel will light up to indicate the charging level. For

additional information regarding the battery power indicator lights, see the full owner's manual.

Powering the System ON and OFF

• When powering the system ON or OFF, do not have your feet on the pedals; a system fault may result.

• The power button (g. 3) on the battery can be accessed through the window in the top of the downtube.

• Power cannot be turned on while the battery is charging.

• If the bike has not moved for 10 minutes, the power will shut o automatically.

123

COMPONENT QUICK START SETTING

Shock Air Pressure

(by Body Weight)

Body Weight in [kg] to [bar] 0.15 × Body Weight [kg] + 2.4 [bar]

Body Weight in [kg] to [psi] 2.2 × Body Weight [kg] + 35 [psi]

Body Weight in [lbs] to [bar] 0.07 × Body Weight [lbs] + 2.4 [bar]

Body Weight in [lbs] to [psi] Body Weight [lbs] + 35 [psi]

Fork Air Pressure 70 [psi] / 4.83 [bar]

Shock Compression Damping 7 clicks in (clockwise) from OPEN

Shock Rebound Damping 7 clicks in (clockwise) from OPEN

Fork Compression Damping 6 clicks in (clockwise) from OPEN

Fork Rebound Damping 8 clicks in (clockwise) from OPEN

Front Tire Pressure 18 [psi] / 1.24 [bar]

Rear Tire Pressure 22 [psi] / 1.52 [bar]

Assist Mode Operation

• On start-up, the assist mode will be o. There are three levels of assistance: Eco, Trail, and Boost.

• The switch on the left side of the handle bar controls the level of assistance provided by the system.

www.pivotcycles.com 1.877.857.4868

Assist and Shifter Switch Function

• The operation procedure detailed below refers to the cycle computer default setting.

• Refer to the Shimano STEPS E8000 System Schematic for the switches part names.

BUTTON CYCLE COMPUTER (A) FUNCTION

Z1 Switch display modes (Current Speed is default and will return after 60 seconds)

(Display Modes: Distance, Odometer, Range, Travel Time2, Avg. Speed2, Max. Speed2, Cadence2, Watts2, Calories2, Clock)

BUTTON ASSIST SWITCH (B) FUNCTION

X1 Increase the level of assistance (Eco, Trail, and Boost)

Y1 Decrease the level of assistance (Press and hold for WALK mode)

BUTTON SHIFTING SWITCH (C) FUNCTION

X2 Up-shift rear derailleur (Pedaling becomes harder)

Y2 Down-shift rear derailleur (Pedaling becomes easier)

1) When Range displayed, the battery level is not displayed

2) Optional Item

3) When WALK assist is functioning Range displays [RANGE ---]

Y1 X1 Y2X2

(B) (C)

(A)

(Z1)

Operating the Cycle Computer

• The table below references the schematic above.

BUTTON CYCLE COMPUTER (A) FUNCTION

Z1 Switch between screens and conrm settings. (Press and hold to access menu screen)

(Menu Screens: Clear, Clock, Bluetooth, ANT, Light, Brightness, Sound, Units, Language, RD Adjust, RD Protection, Exit)

BUTTON ASSIST SWITCH (B) FUNCTION

X1 / Y1 Move menu cursor, adjusting settings, etc.

LETTER DISPLAY ITEM

ABattery level indicator

BGear Position

CAssist Gauge

DAssist Mode Display

ECurrent Speed / Display Mode

1) Only displayed when using Di2

2) [ECO] mode automatically activates as remaining battery capacity declines

Screen Display

• The content below details the display layout for the cycle computer (A) in the Shimano STEPS E8000

System schematic.

(B)(A)

(C)(D)

(E)

BASIC OPERATION

www.pivotcycles.com 1.877.857.4868

BIKE SET-UP

Setting Proper Sag

• Pivot uses dierent sag indicators depending upon

the bike model.The Pivot Shuttle uses Sag Indicator B.

1. Always set sag with the blue compression damping

adjust lever turned to the open position. (g. 1)

2. Have the rider stand on the pedals, preferably with

their hydration pack on, and have them sit down

hard into the saddle to achieve accurate sag settings.

The rider does not need to bounce up and down nor

should they sit down gently. If they sit down hard

once, the suspension will cycle well into the stroke

and return to the natural sag setting with the rider

in the saddle.

3. With the rider in the saddle and not moving, slide

the O-ring up into position against the air can. (g. 2)

4. Once the O-ring is set in place, have the rider slowly

step o the bike so as not to move the O-ring.

5. Make adjustments to the sag by removing or adding

air so that steps 2-4 result in the O-ring lining up

with the red line on the sag indicator (g. 3). It will

be necessary to cycle the shock after adding or

subtracting air before re-checking sag as the large

Evol negative air chamber will need to equalize

pressure with the main chamber each time air is

added or removed.You can do this by pushing down

on the saddle several times to compress the shock

past the sag point.

Setting Compression Damping on the Fox DPX2

• The compression damping lever is a tuning tool to adjust compression support.

• All bikes can be run in the open position at all times and still perform well.

• Riders under 82 [kg] (180 [lbs]) will generally run the shock in the open position most of the

time.

• Riders over 82 [kg] (180 [lbs]) and aggressive riders may prefer the middle setting for more

mid-stroke support.

• The rmest setting is best suited for riding to the trail, long re road climbs, and smooth XC

courses.

1OPEN

MEDIUM

FIRM

Setting Open Mode Adjust on the Fox DPX2

• The Open Mode Adjust screw ne tunes the compression damping in the open position.

• The adjustment screw is a 3mm hex screw inside the top of the compression damping lever.

• This adjuster oers 10 additional ne tune adjustments for the open mode.

• Turning the screw clockwise will increase low speed compression damping; turning the

screw counter-clockwise will decrease low speed compression damping.

• Most riders will nd 7 clicks from full open is a good starting point.

www.pivotcycles.com 1.877.857.4868

Setting Rebound Damping on the Fox DPX2

• Rebound is set from the most open (fully counter-clockwise) position.

• The rebound setting is determined by the air pressure in the shock.

• Refer to the table below for the suggested rebound setting. The number in the chart

refers to how many clicks in (clockwise) from the open setting the rebound should be set.

AIR PRESSURE SUGGESTED REBOUND

SETTING

[bar] [psi]

< 8.3 <120 Open

8.3 - 9.7 120-140 1

9.7 - 11 140-160 2

11 - 12.4 160-180 3

12.4 - 13.8 180-200 4

13.8 - 15.2 200-220 6

15.2 - 16.5 220-240 7

16.5 - 17.9 240-260 9

17.9 - 19.3 260-280 11

19.3 - 20.7 280-300 12

BIKE SET-UP

Setting Air Pressure on the Fox 36 Fork

• Fox recommends setting sag between 15% and 20% of the total fork travel. The Shuttle comes with a

150mm fork, so the proper sag measurement is 22.5 - 30.0mm.

• The air pressure in the Fox 36 fork should not exceed 8.3 [bar] (120 [psi]).

• To achieve the proper sag, reference the chart below for an initail starting point.

RIDER WEIGHT FOX 36

AIR PRESSURE

[kg] [lbs]

55 - 59 120 - 130 3.0 [bar] / 43 [psi]

59 - 64 130 - 140 3.2 [bar] / 46 [psi]

64 - 68 140 - 150 3.5 [bar] / 51 [psi]

68 - 73 150 - 160 3.8 [bar] / 55 [psi]

73 - 77 160 - 170 4.1 [bar] / 59 [psi]

77 - 82 170 - 180 4.3 [bar] / 63 [psi]

82 - 86 180 - 190 4.6 [bar] / 67 [psi]

86 - 91 190 - 200 4.9 [bar] / 71 [psi]

91 - 95 200 - 210 5.2 [bar] / 75 [psi]

95 - 100 210 - 220 5.4 [bar] / 79 [psi]

100 - 105 220 - 230 5.7 [bar] / 83 [psi]

105 - 109 230 - 240 6.0 [bar] / 87 [psi]

109 - 114 240 - 250 6.3 [bar] / 91 [psi]

www.pivotcycles.com 1.877.857.4868

Recommended Tire Pressure

• Tire pressure is an important factor on having the bike ride properly. If the tire pressure is too high, the tire

will not conform to ground, reducing traction. If the tire pressure is too low, the tire could pinch at.

• It is important to have an accurate pressure gauge when setting tire pressure; preferably a digital gauge

with a 0.03 [bar] (0.5 [psi]) accuracy.

• The recommended tire pressure will vary slightly based on rider weight, riding style, and terrain.

• Some riders may nd it helpful to start a ride at a slightly higher pressure than recommended and let out

a little air throughout the course of the ride until you nd your ideal riding tire pressure.

RECOMMENDED TIRE PRESSURE

FRONT REAR

1.24 [bar] / 18 [psi] 1.52 [bar] / 22 [psi]

BIKE SET-UP

Adjusting Saddle Height

• The seat post collar on the Shuttle can be loosened and tightened with a 4mm hex wrench.

• Before raising or lowering the seat height, using a 2mm hex wrench, loosen the head tube cable port

securing the dropper post housing.

• The dropper post cable should be routed through the cable port on the driveside of the head tube. This

cable port cap is used to hold the dropper post cable and cycle computer wire in place.

• Be sure to re-tighten the cable clamp on the head tube cable port after adjusting the saddle height.

4mm

Hex Wrench 2mm

Hex Wrench

Setting Compression Damping on the Fox 36 Fork

• To set compression, start from the open (or fastest) position by turning the black compression dial on the

top of the right fork leg counterclockwise until it stops clicking.

• Turn black dial clockwise in 2-8 clicks in (depending on rider weight). Most riders should feel comfortable

with 6 clicks in as a starting point.

• Lighter riders will generally prefer less compression damping (fewer clicks from open).

Setting Rebound Damping on the Fox 36 Fork

• To set rebound, start from the open (or fastest) position by turning the red rebound dial on the bottom of

the right fork leg counterclockwise until it stops clicking.

• Turn red dial clockwise in 5-8 clicks in (depending on rider weight). Most riders should feel comfortable

with 8 clicks in as a starting point.

www.pivotcycles.com 1.877.857.4868

Connecting to E-Tube Project

• The display layout and switch operation can be customized through the Shimano E-Tube Project.

• The Shimano E-Tube project can be accessed via the Shimano E-Tube Project app available in the App

Store or through the software, which can be downloaded from Shimano's website.

• The E-Tube Project app is compatible with both Android and Apple devices. At the time of publication, the

E-Tube Project software is only available for Windows operating systems. Check Shimano's website for the

latest information regarding the E-Tube Project software.

• LinkstoShimano'swebsitetodownloadthesoftware arein the "Reference Material" Section of thismanual.

Connecting via the E-Tube Project app:

1. Before setting up a connection, turn on the Bluetooth connectivity of the smart phone or tablet.

2. Open the E-Tube Project app and set it to receive for Bluetooth signals.

3. Press X1 or Y1 button on the Assist Switch (B) to select [Start] on the cycle computer (A). Refer to the

diagram on Page 2.

4. To start the Bluetooth connection, press the Z1 button on the cycle computer (A). If you press the Z1

button again, during the connection process, the transmission will be interrupted and the screen will

return to the menu list.

5. When the connection is successful, the Shimano STEPS logo will be displayed. If the connection is not

successful a "Connect failure" message will appear.The rst time you connect the password is "000000".

6. When the connection is successful, the unit name will be displayed in the E-Tube Project app. Select

the unit name in the app to customize the unit.

7. To disconnect, cancel the Bluetooth connection from the smart phone or tablet. The cycle computer

(A) will exit the connection mode and return to the regular operation mode.

Connecting via a computer with the E-Tube Project software:

1. Connect a USB cable from the computer to the Communication Box (SM-PCE1). The Communication

Box is not included with Shuttle and must be purchased separately.

2. Connect the Communication Box to the open port in the cycle computer.

3. Open the E-Tube Project Software and select E8000 from the Shimano STEPS menu.

4. On the next screen select "Connection Check".

5. On the following screen conrm by selecting "Next".

6. The next screen will list the devices recognized by software.There should be 5 devices listed: The drive

unit, the cycle computer, the rear derailleur, the assist switch, and the shift switch.

7. Select "Complete" to nish the operation and complete the connection to the system.

SHIMANO STEPS E8000 SYSTEM

Main Menu for E-Tube Project

• The main menu to the E-Tube Project has three main components that are relevant for the consumer to

know how to navigate and operate: Customize, Update Firmware, & Preset.

• In the E-Tube Project software, after clicking "Complete" a list of buttons will appear corresponding to the

menu options.

• When using the E-Tube Project app, after making the connection, a group of icons will appear that

correspond to the menu items. The table below will show what the icons look like.

ICONS IN E-TUBE PROJECT APP

CUSTOMIZE UPDATE FIRMWARE PRESET

www.pivotcycles.com 1.877.857.4868

Update Firmware Menu in E-Tube Project

• There is a button in the main menu to update the rmware.

• By pressing the "Update Firmware" button, the software automatically searches for and downloads any

update for the system.

• Once the program has completed any updates, each component of the Shimano STEPS E8000 System will

be listed with the corresponding version of the latest rmware for that component.

SHIMANO STEPS E8000 SYSTEM

Preset Menu in E-Tube Project

• The E-Tube Project allows saving and loading custom settings les.

• Any customized setting can be saved as a preset settings le.

• Settings les can also be pulled from a bike and saved as a preset settings le. The saved settings can be

uploaded to other bikes to duplicate the settings on other bikes.

• To create a preset settings le on the app:

1. Make any changes to the settings of the bike in the Customize menu.

2. Upload the changes to the bike.

3. Open the Preset menu and click on, "Loading settings from the bike".

4. Click on the "Connected" button on the bottom of the screen.

5. The settings that were just uploaded will now appear listed on the screen. By scrolling to the bottom

of the screen, the le name can be edited.

6. Click on the download button on the bottom of the screen. A conrmation of the successful download

will appear.

7. Now, the saved a preset settings le will appear under the "Load a settings le" option within the

Preset menu.

Customize Menu in E-Tube Project

• The Customize menu is sub-divided into menus for individual units: Drive Unit, Display Unit, Switch Setting,

and Multi Shift Setting

• The tables below show the available options within the Customize menu.

DRIVE UNIT SETTING DESCRIPTION

Light Sets whether to use a light.

DISPLAY UNIT SETTING DESCRIPTION

Display Units Switches the measurement units between km and mile.

Display Switchover Sets whether to display traveling time, average speed, maximum speed, cadence, and current time.

Time Setting Sets the correct current time.

Beep Setting Switches the beep sound on or o.

Brightness Adjusts the backlight's brightness.

Dislay Language Sets the language used between English, French, German, Dutch, Spanish, and Italian.

SWITCH SETTING DESCRIPTION

Shifting Switch Sets the shift direction of buttons X2 and Y2 on the Shifting Switch (C)

MULTI SHIFT SETTING DESCRIPTION

Multi Shift Switches the multi shift function on or o.

Gear-shifting Interval Adjusts the shifting speed of multi shift mode. Does not aect shifting speed of individual shifts.

Gear Number Limit Sets how many gears the derailleur will shift through in multi shift mode.

www.pivotcycles.com 1.877.857.4868

Battery Charging Notes

• The battery does not come charged and must be charged completely before the rst use.

• Only charge the battery with a desginated charger, such as the one included with the bike.

• Battery can be used once the LEDs on the power panel light up.

• When removing the charger from the outlet or the port, pull on the plug, not the cord.

• When charging the battery, plug the cord into the wall outlet rst, and then into the battery.

• Be sure the the charger is on a at and stable surface, when charging.

• Do not leave the battery fully depleted for an extended period of time. This will cause the battery to

deteriorate and reduce the battery capacity.

Charger LED Lamp

• After charging has started, the LED lamp on the charger lights up.

Charger LED Lamp LED INDICATOR DESCRIPTION

Lit Up Battery Charging (or within 1 hour after the completion of charging)

Blinking Charging Error

Turned o Battery Disconnected (or 1 hour or more after the completion of charging)

Battery Power Panel LED Lamps

• You can check the charge level of the battery during charging and while riding.

BATTERY LEVEL WHILE CHARGING* BATTERY LEVEL WHILE RIDING*

0% - 20% 0%, Power OFF / Shutdown

21% - 40% 20% - 1%

41% - 60% 40% - 21%

61% - 80% 60% - 41%

81% - 99% 80% - 61%

100% 100% - 81%

: No Light : Lit Up : Blinking

SHIMANO STEPS E8000 SYSTEM

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Pivot Bicicletta

Pivot

Pivot SHUTTLE LT Guida rapida

Manuali Bicicletta popolari di altre marche

RAMBO

RAMBO R1000X2M-FF-BFD Manuale utente

Vermeiren

Vermeiren SAFARI Manuale utente

Velec

Velec A2/36V Manuale utente

Coswheel

Coswheel A-ONE Manuale utente

Betzold

Betzold 97869 Manuale utente

Cervélo

Cervélo S3 2019 Manuale utente

Tenways

Tenways AGO X Manuale utente

Festo

Festo EGSC-BS-KF Manuale elenco delle parti

Gio Electric

Gio Electric H1 Volt Manuale utente

GOGOBEST

GOGOBEST GM30 Manuale utente

DAHON

DAHON CIAO - 2009 Manuale utente

Aprimatic

Aprimatic ONDA 500 Guida rapida

MV Agusta

MV Agusta Lucky Explorer GRAVEL Manuale di istruzioni

Greyp

Greyp G6 Series Manuale utente

Babboe

Babboe Carve-E Manuale utente

Huka

Huka orthros Manuale utente

Xtracycle

Xtracycle Stoker 2021 Manuale utente

APRILIA

APRILIA DORSODURO 750 ABS 2015 Manuale utente