Planex FW-100TA Manuale utente
10/100Mbps PCI Fast Ether
net Adapter
FW-100TA
10/100Mbps PCI Fast Ether
net Adapter
FW-100TA
USER'S MANUAL
FW-100TA
Chapter 2
Installation
Appendices
About this Manual
Appendices
Appendix A
Specifications
Lists the technical specifications of the PCI Fast Ethernet Adapter.
Chapter 1
Introduction
Describes the PCI Fast Ethernet Adapter and its exterior features. Please be certain to read
this chapter before installing the PCI Fast Ethernet Adapter.
This user
'
s manual provides product overview and operation instructions of
the 10/100Mbps PCI Fast Ethernet Adapter FW-100TA. The manual covers
the following topics:
Version: 3.0 EC
Trademarks
Copyright @2002 PLANEX COMMUNICATIONS INC.
Contents subject to change without prior notice.
Pci is a registered trademark of PLANEX COMMUNICATIONS INC.
All other trademarks belong to their respective proprietors.
Copyrigh Statement
No part of this publication may be reproduced in any form or by any means
or used to make any derivative such as translation, transformation, or
adaptation without permission from PLANEX COMMUNICATIONS INC.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class B computing device pursuant to Part 15 of the FCC Rules, which are
designed to provide reasonable protection against electromagnetic
interference in a commercial environment. Changes or modifications to the
equipment not expressly approved by the party responsible for compliance
could void the user
'
s authority to operate the equipment.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may
cause radio interference in which case the user may be required to take
adequate measures.
FW-100TAFW-100TA
11
2
3
21
2
3
4
2
2
3
3
6
6
7
8
10
Chapter 1 Introduction
Product Overview ...........................................
Features ............................................................
Package List ....................................................
Parts Terminology............................................
Chapter 2 Installation
System Installation..........................................
Network Cable Connection............................
Connecting the power .....................................
Appendix A
Specifications....................................................
Appendix B
Contents of the Driver Diskette .........................
21
FW-100TA
Chapter 1
Introduction
The FW-100TA is a single-chip PCI Bus 100BASE-TX Fast Ethernet
Adapter designed for IBM PC compatibles with a PCI bus slot.The Fast
Ethernet adapter complies with IEEE 802.3 10Base-T/ 802.3u 100Base-TX
standards and PCI Rev. 2.1, 2.2 specifications.The adapter is equipped with
Auto-Negotiation function, and can automatically detect the appropriate
communication rate (10Mbps/100Mbps) and duplex mode (half/full-duplex)
whenever it is connected to a hub with Auto-Negotiation support.
The FW-100TA supports flow control in full duplex (IEEE802.3x), a feature
unavailable in traditional ordinary NICs.
When combined with a switching hub with IEEE802.3x Flow Control
support, the FW-100TA performs flow control in full duplex to prevent
packet losses.
As a PCI bus adapter, the FW-100TA is jumper less. All resources including
I/O base addresses and IRQ are automatically assigned at system startup.
●Single-chip PCI Bus 100BASE-TX Fast Ethernet Adapter
●Fully Comply with IEEE 802.3u and IEEE 802.3 standards
●Full-Duplex available in both modes for up to 200Mbps throughput
●Optimal line-speed set automatically via Auto-Negotiation function
●Shielded RJ-45 connector provides unified 100BASE-TX and 10BASE-T
network media interface.
11Product Overview
12FW-100TA Features
3
FW-100TA
4
FW-100TA
3. LED
The LED is located above the RJ-45 connector:
4. 100BASE-TX and 10BASE-T
If users have an existing 10BASE-T LAN, it is likely they will easily be
able to upgrade to 100BASE-TX. However, there are some important
differences between the two types of networks.
5. Cable Type
●100BASE-TX only supports Cat.5 TP cable.
●10BASE-T supports Cat.3, 4, or 5 TP cable.
Whenever installing new cable, use Cat.5 TP cable.
6. Repeater Hubs (only):
(1)100BASE-TX
Two types of 100BASE-TX Repeater Hubs exist: Class I and Class II
●Class I Hubs cannot be attached to any other Repeater Hub.
●Class II Hubs can be connected with one other Class II Repeater Hub.
(2)10BASE-T
10BASE-T Repeaters are not classified.
●Four Repeaters are allowed on a collision domain.
(3)100BASE-TX Link Distance Limits:
Strict limits are placed on the length of cable allowed between devices.
●Workstation to Hub = 100m max.
●Class-II Hub to Class-II Hub=5m max.(when workstations are 100m
from Hubs)
●Network Diameter = 205m max. (while using two Class II Hubs)
The product package contains the following items:
●FW-100TA Ethernet Adapter
●Driver diskette
●This User
'
s manual
If any item is found missing or damaged, please contact your local PCI
reseller for replacement.
1. Hardware overview
2. RJ-45 Port
This single port Fast Ethernet Adapter is capable of handling both
100BASE-TX and 10BASE-T network data. One RJ-45 female socket is
provided for twisted pair cable attachment. The socket has been shielded for
improved EMI protection.
13Packing List
14Parts Terminology
100M
LINK/ACT
Function
Blinking: TX/RX
Green
Green 100M Mode
Name Color
5
FW-100TA
6
The proper installation of these Fast Ethernet Adapters can be divided into
three phases:
●SYSTEM: Putting the Adapter into a computer.
●CABLE: Connecting the Adapter to the network.
●SOFTWARE: Installing and configuring the NOS driver.
●Disconnect the computer
'
s power supply.
●Open the computer.
●Remove the protective bracket from any available PCI-Bus
Expansion Slot.
●Save the screws!
●Remove the Adapter from the bag.
●With the Adapter
'
s bracket facing out, insert the Adapter into the
PCI- Bus slot.
●Press firmly, but do not bend the pins!
●Secure the Adapter bracket with the screws.
●Replace the computer
'
s cover.
●Plug one end of a TP cable into the Adapter
'
s RJ-45 socket.
●Plug the other end of the cable into any 100BASE-TX or 10BASE-T
Hub port.
See 100BASE-TX and 10BASE-T section for details on cable type and
length.
Chapter 2
Installation
21System Installation
22Network Cable Connection
87
FW-100TA
The Driver Diskette included with this Fast Ethernet Adapter contains
drivers for most major network operating systems (NOS). Two important
files are also included in the root directory. These files are README files.
●Step-by-Step instructions on installing drivers are located in
the README files.
●For exact information, look in the Driver diskette
'
s respective driver
directory.
Standards: IEEE 802.3u 100BASE-TX
IEEE 802.3 10BASE-T
Bus Type: PCI Bus specification revision 2.1, 2.2
Network Interface: One shielded RJ-45 phone-type jack
Network Modes Supported: 100BASE-TX (Category 5 TP cable required)
10BASE-T (Category 3, 4, and 5 TP required)
Full-Duplex available in both modes
LEDs: 100M (Green), LINK / ACT (Green)
(Action blinking only)
Dimensions: 120 x 42 mm (4.72 x 1.65 in.)
Operating Temp.: 0°~ 55°C (32°~ 131°F)
Storage Temp.: -20°~ +70°C (-4°~ 158°F)
Humidity: 10% ~ 90% non–condensing
23Diskette Software
Appendix A
Specifications
109
FX-05/08EA
The supplied driver diskette contains the following directories.To indtall
eachdriver, please see the respective explanation file included in the
diskette.
\LINUX LINUX Kernal 2.2/2.4 driver description file
\NETWARE
\ODI NetWare ODI client driver
\NW312 NetWare 3.12 server driver
\NW411 NetWare 411 server driver
\NW50 NetWare 50 server driver
\WIN95 Driver description file for Windows95
\WIN98/98SE Driver description file for Windows98/98SE
\WINME Driver description file for WindowsME
\WINNT WindowsNT 3.51/4.0 driver descrition file
\WIN2K Driver description file for Windows2K
\WINXP Driver description file for WindowsXP
\DOS IBM DOS LAN Services driver
This chapter describes how to install the FW-100TA into a computer and
how to connect a network cable to the Ethernet adapter.Since the adapter is
a PCI bus device, there is no need to manually configure the device.
The computer automatically assigns appropriate I/O base addresses and IRQ
at system startup.
Appendix B
Contents of the Driver Diskette
FW-100TA
第一章 簡介...................................................................
第二章 主要特性
主要硬體特性........................................................
RJ-45 .....................................................................
LED 燈....................................................................
100BASE-TX 及10BASE-T................................
線材種類.................................................................
中繼集線器 ............................................................
100BASE-TX.........................................................
10BASET...............................................................
100BASE-TX 連線距離制...................................
第三章 網路卡安裝
系統安裝...........................................................................
網路線材連接..................................................................
驅動程式安裝..................................................................
21
2
3
4
5
62
31
32
33
目 次
FW-100TA
商標說明
NetWare和Novell是Novell Corporation的註冊商標，Microsoft
Windows 95/98/Me和Microsoft Windows NT/2000是Microsoft
Corporation的商標或美國註冊商標，其他的牌子及其商品名
稱的註冊商標為廠商所有。
著作權
任何全部或部份的出版品，不能以文章格式。內容意思及任
何衍生作品，例如翻譯或改編性的文章，從1976年的美國著
作權法規定，不能敘述廠商內容的法律規範。
FCC安全指示
本產品已經過＜Class B 數位裝置＞測試及嚴格要求。此限制
按照FCC規則的15個部分。這些限制是為了在居住環境中安
裝任何設備，提供合理的保護，和對抗有害干擾而設計。
若未按照指示正確的安裝或使用，此設備可能會產生或散發
射頻能源，並可能對電訊交通造成有害的干擾。但是，並不
保證在特殊的安裝中，不會產生干擾。
2
4
5
5
5
5
6
6
6
6
8
8
9
Indice
Altri manuali Planex Adattatore
Planex
Planex BT-01UDE Manuale utente
Planex
Planex GW-US300Mini2 Manuale utente
Planex
Planex GW-NS54GM Manuale utente
Planex
Planex URS-02 Manuale utente
Planex
Planex GW-US54GXS Manuale utente
Planex
Planex GN-1200TW3 Manuale utente
Planex
Planex BT-MicroEDR1X Manuale utente
Planex
Planex GW-US54GZL Manuale utente
Planex
Planex GW-US54Mini Manuale utente
Planex
Planex UE-100TX Manuale utente
