Pleiger 362MC Manuale utente

Pleiger Elektronik GmbH & Co. KG

D-58456 Witten - Im Hammertal 51

D-58423 Witten - P.O.Box 32 63

Telephon +49 (0) 23 24 * 3 98- 0

Telefax +49 (0) 23 24 3 98- 3 89

www.pleiger-elektronik.de

[email protected]

PLEIGER ELECTRONICS 362MC

Manual

Operation

Installation

Connection

Technical data

Hardware extensions

Functional extensions

Commissioning help

Edition: 6/2007

Subject to modifications

Pleiger Elektronik

GmbH & Co. KG

Page: 2 Manual for 362MC Edition: 6/2007 Subject to modifications

Contents Page

1Introduction ..................................................................................................... 4

2Display and operating elements ..................................................................... 5

2.1 Display .................................................................................................... 6

2.2 Operation ................................................................................................ 6

3Operating modes ............................................................................................ 7

3.1 Automatic mode ...................................................................................... 7

3.1.1 Setpoint entry ................................................................................ 7

3.2 Switching between Manual/Automatic ..................................................... 8

4Manual / Emergency manual mode ................................................................ 8

5Commissioning extension .............................................................................. 9

5.0 Password entry ....................................................................................... 9

5.1 Additional Menu selection with QuickSet ................................................. 11

5.2 Commissioning menu ............................................................................. 12

5.3 Setpoint menu ......................................................................................... 13

5.3.1 Explanatory note on setpoints ....................................................... 14

5.3.2 Explanatory note on the switching filter ......................................... 14

5.3.3 Explanatory note on the limit value alarm ...................................... 14

5.4 Controller profile menu ............................................................................ 15

5.4.1 Entering parameters for two controllers ........................................ 15

5.4.2 Entering parameters for one controller only .................................. 15

5.5 Controller parameters menu ................................................................... 16

5.5.1 Explanatory note on controller types ............................................. 17

5.5.2 Explanatory note on controller structure ....................................... 19

5.5.3 Explanatory note on controller output parameters ........................ 20

5.6 Input menu .............................................................................................. 21

5.6.1 Explanatory note on calibration ..................................................... 22

5.6.2 Explanatory note on scaling .......................................................... 22

5.7 Output menu ........................................................................................... 23

5.8 Display menu .......................................................................................... 24

5.8.1 Explanatory note on controller inputs/outputs ............................... 24

6Monitoring functions and error messages ...................................................... 25

6.1 System monitoring functions ................................................................... 25

6.1.1 Explanatory note on Param error .................................................. 25

6.1.2 Explanatory note on ROM error and RAM error ............................ 25

6.1.3 Explanatory note on the Reset function for the controller .............. 26

6.1.4 Explanatory note on Watchdog error ............................................. 26

6.2 Sensor monitoring functions ................................................................... 26

7Service interface ............................................................................................. 27

7.1 Service programme McDiag ................................................................... 27

8Installation ...................................................................................................... 28

9Connection ..................................................................................................... 29

9.1 Terminal assignments ............................................................................. 29

9.2 Connection of supply voltage .................................................................. 30

9.3 Connection of the switching outputs ....................................................... 30

9.3.1 Connection with AC switching output contacts ............................. 30

9.3.2 Connection with floating switching output contacts ...................... 30

9.4 Connection of the alarm output ............................................................... 31

9.5 Connection of the binary inputs ............................................................... 31

9.6 Connection of the remote resistance-type sensor .................................. 31

Pleiger Elektronik

GmbH & Co. KG

Edition: 6/2007 Subject to modifications Manual for 362MC Page: 3

Contents Page

9.7 Connection of a U/I measured-value transmitter ..................................... 31

9.8 Connection of the PT100 sensor............................................................. 32

9.9 Connection of a I -value transmitter at the 1st analogue input .................. 32

9.10 Connecting cable ................................................................................... 32

10 Technical data ................................................................................................ 33

Appendix A: Reference overview

Appendix A1: Overview of menu structure for standard functions ...................... 34

Appendix A2: Parameters from A to Z for standard functions ............................. 35

Appendix A3: Value assignments from A to Z for standard functions .................. 36

Appendix A4: Error displays and messages from A to Z ..................................... 37

Appendix A5: Symbols employed in this manual ................................................ 37

Appendix B: Hardware extensions for the 362MC

Appendix B1: Hardware extension - 2nd relay set ................................................ 38

Appendix B2: Hardware extension - Analogue outputs ........................................ 39

Appendix B3: Hardware extension - RS485/RS422 communication interface.... 40

Appendix C: Functional extensions for the 362MC

Appendix C1: Special function - Trend compensation ......................................... 41

Appendix C2: Functional extension - Disturbance compensation ....................... 43

Appendix C3: Functional extension - Setpoint programme ................................. 47

Appendix C4: Functional extension - Differential actual value ............................. 51

Appendix D: Commissioning help

Appendix D1: Steps for commissioning .............................................................. 52

Appendix D2: Profile memories and factory presets ........................................... 53

Appendix D3: Programme entries table for setpoint programmes ...................... 57

362MC Delivery configurations ...................................................................... 58

Pleiger Elektronik

GmbH & Co. KG

Page: 4 Manual for 362MC Edition: 6/2007 Subject to modifications

1 Introduction

The Pleiger multi-function controller 362MC combines a large number of controller functions in a single

compact housing designed for installation in a control panel. A powerful microcontroller, a large parameter

memory and a two-line alphanumeric display support simple and swift operation and commissioning of the

controller.

The 362MC incorporates the following controller functions in one unit:

•Two-point controller

•Three-point controller with separate parameter sets for both outputs

•Three-point step controller, with optional feedback of controller output

•Continuous controller

•Cascade step controller

Two independent control loops can be operated with one controller unit, provided that the controller is per-

missible for the application concerned.

The 362MC incorporates a large number of special features, such as:

•an actual-value display and manual controller output adjustment which function

independently of the microcontroller to enable manual emergency operation for

switching controllers, even in the event of processor failure;

•a large non-volatile parameter memory to enable storage of up to 50 different controller

configurations for frequently required applications;

•a two-line alphanumeric LCD display for process data and easily comprehensible operating

prompting;

•a serial service interface which is accessible via the front panel of the controller, to enable

connection of a terminal or a PC to the Pleiger service programme 362McDiag.

In addition to the user-friendly operating and display functions, the 362MC does, of course, also provide

additional control functions to enable the safe and reliable control of complex systems, such as

•differential trend compensation via the second measuring sensor, for enhanced control of

systems with large dead times;

•switch-over to a second setpoint via an external signal;

•inputs for an external setpoint and for logical adjustments and interlocks.

The 362 MC can be supplied in a configuration geared specifically to the application concerned, by means

of different voltage variants (230V-AC, 115V-AC), different measurement ranges (0-200°C, 0-500°C,

0-100%) and different component variants for the inputs (PT100, 4-20mA, 0-10V) and outputs (relays

with supply voltage or floating contacts).

Hardware extensions are also available, such as

•a 2nd relay group for switching outputs,

•a module with 2 analogue outputs - 0(4)-20mA or 0-10V,

•a module with RS 485/422 serial data interface

and functional extensions, such as

•additive disturbance compensation weighted via any characteristic with five interpolation

points for advance compensation of the controlled system,

•setpoint programmes for time-dependent setpoint adjustments and

•difference input for actual values, e.g. for differential pressure control of pumps.

In the appropriate configuration, the single 362MC unit is thus able to replace the Pleiger controllers and

supplementary modules 361-D, 362-D, 366-D and 366-V.

Pleiger Elektronik

GmbH & Co. KG

Edition: 6/2007 Subject to modifications Manual for 362MC Page: 5

2 Display and operating elements

The 362MC controller incorporates a 2½-digit LED actual-value display for the 1st controller which is

clearly legible at a distance. For special applications, the display is also available as a 3½-digit variant

(with decimal digit or for special measuring ranges). The 362MC additionally features an two lines LCD

process data and parameter display. During normal operation of the controller, this display is employed to

display various process variables. The display also provides easily comprehensible operator prompting for

all entry operations.

Eight buttons are integrated in the foil of the front panel to control the display, to enter data, to switch the

operating mode and to activate emergency manual mode. The buttons are arranged in three groups.

A practical, replaceable labelling field is provided under the foil for identification of the measuring point.

After removing the front frame and

lifting the lower part of the foil, the

fuse for switching outputs and the

connector for the service interface

are also accessible after installation

of the controller. The labelling field is

simple to replace.

Fuse F2 Connector for service interface Front frame

LED actual-value display

LED Auto Actual value X of 1st controller

ON = Automatic mode without decimal place

OFF= Manual / Emergency (1st analogue input direct;

manual mode PT100 input in °C,

4-20mA input in %)

LCD display lines 1 + 2

(Operating display and

Switching output buttons operator prompting)

+



= actuator OPEN



- = actuator CLOSED

(only by Emergency

manual mode)

Selection + entry buttons

Man and Auto buttons  

 

 = Select+ increase value

Man = Manual / Emergency 



= Select+decrease value

manual mode Prgm=Select+save

(only together with Exit) Exit =Cancel+abort

Auto = Automatic mode (Exit+Man=Manual /

Emergency manual mode)

Labelling field

for identification of

measuring points

Pleiger Elektronik

GmbH & Co. KG

Page: 6 Manual for 362MC Edition: 6/2007 Subject to modifications

Menu 1 Menu 2 Menu n

Parameter

Value

Param. 2

Value+1

Value-1

Save

value

Menu selection

Parameter selection

Parameter entry

Example of

operational display

Line 1

Line 2

2nd L1

2nd L2

On power up, the

362MC always

displays the type and version no.

2.1 Display

On power up, the controller always displays the type and version no. first of all, before

switching to menu 1, the operational display. Here the process data are shown in the

two-line LCD display. Display lines 1 and 2 are visible in normal operating

mode. By pressing the Prgm button, the display can be switched to a

second mode (2nd line 1 and 2nd line 2)

for as long as the button is held.

The user can assign the process data

in the operational display to the lines via

the commissioning menu Display (5.8).

2.2 Operation

Operation of the controller, configuration and setting of the controller

parameters are carried out with operator prompting in 3 selection levels.

Menu selection constitutes the highest selection level. In normal

operating mode the menu selection remains hidden and the process

data are shown on the LCD display. The desired menu is selected via the 



and buttons.

The menu name is now shown in the 1st line of the LCD display instead of the process data . Each menu

groups together entry items and parameters which are closely linked. The Prgm button can be used to

branch to the desired menu and the parameter selection function. The desired parameter is selected

here in the same manner, using the 



and buttons.

The 1st line of the display shows the name and the 2nd line the value of the selected parameter. If the

selected value now requires to be altered, the Prgm button must be pressed to branch to the parameter

entry function. Here the value can

be altered with the 



and buttons.

The value is entered and saved via

the Prgm button.

If the Exit button is pressed at any

point, the current selection will be

aborted. From the parameter entry

function the system will branch back

without altering the set value to

the parameter selection function,

from parameter selection the system

will always branch back to he menu

selection function, and from menu

selection menu 1 - the operational

display - will always be activated.

Should no button be pressed over a

period of 60 seconds during the

selection or entry process, the

operational display will be

re-activated automatically.

Menu name

Parameter name

Parameter value

Value entry

Example of display

at selection and entry

Pleiger Elektronik

GmbH & Co. KG

Edition: 6/2007 Subject to modifications Manual for 362MC Page: 7

3 Operating modes

The 362MC incorporates two operating modes - Automatic and Manual / Emergency manual mode. A

modified menu is provided for each operating mode. Both operating modes offer an extended version of

the menu for commissioning purposes. This extension to the menus for configuration and

parameterisation of the controller is protected by a password to prevent unauthorised use.

3.1 Automatic mode

The green Auto LED lights up; the controllers are operating in a closed-loop system. The setpoints can

be altered via the setpoint entry or the commissioning menus can be activated via the menu selection

function, provided that the valid password has been entered.

3.1.1 Setpoint entry

After selecting the Setpoint Entry

menu under the menu selection

option in Automatic mode, the

setpoints and the alarm limits of

both controllers can be altered.

The 1st character of the name

displayed under the entry option

denotes the number of the controller - 1 or 2.

The letter A or B appears as the final character,

to distinguish between the main setpoint (A)

and the second setpoint (B) that becomes active

in the case of external setpoint switching.

The value for the lower alarm limit

of each controller is indicated by -

and the value for the upper alarm

limit is indicated by +.

See also Explanatory note on limit alarm (5.3.3).

This presentation of the setpoint entry procedure is based on the assumption that both controllers have

been configured as fixed setpoint controllers with setpoint type „fixed value“. The 1st controller setpoint is

101.0°C for Setp A and Setp B, irrespective of the setpoint switching function. 82.0°C is defined under

Setp A for the 2nd controller.

When external setpoint switching applies, Setp B is set at 65.0°C. When a different setpoint type is

configured, the setpoint entry display has a different appearance.

In the case of the setpoint type external setpoint (extern), an external value connected

at the input becomes the setpoint. It is thus not possible to alter this value by entering a

different value.

When the controller is implemented with a setpoint programme, the user

can switch between the stored programme numbers 1 to 5 (in this example 2).

See also Functional extensions (Appendix C3).

Display example

with password

entry to the

commissioning

Operational display Setpoint menu Password menu

Menu selection in automatic mode

Entry selection Abort

Value+1

Value-1

Save

new value

Alter value

Pleiger Elektronik

GmbH & Co. KG

Page: 8 Manual for 362MC Edition: 6/2007 Subject to modifications

The buttons are provided only for the manual adjustment of switching

outputs on the 1st controller in Emergency manual mode, and have no other functions.

3.2 Switching between Manual/Automatic

Manual / Emergency Manual mode will only be activated if the user presses the Man and Exit button

simultaneously. This eliminates the possibility of Automatic mode being deactivated unintentionally or by

mistake. The green „AUTO“ LED turns off, and the text MANUAL is shown in the 1st line of the LCD display

in alternation with the process value. Manual operation of the outputs and emergency manual mode for the

switching output of the 1st controller are active.

Automatic mode is activated again by pressing the Auto button. The green LED marked „Auto“ lights up.

4 Manual / Emergency manual mode

When Manual / Emergency manual mode is active, buttons 



-and +



are used to adjust the

1st controller´s switching output. When the +



button is pressed, the output is switched to +, as a result

of which the connected actuator is operated in OPEN direction. When the 



-button is pressed, the

output is switched to -, as a result of which the actuator is operated in CLOSED direction.

This Emergency manual mode for the 1st controller operates irrespective of whether the micro-

controller is operational. The 2½-digit actual-value LED display of the 1st controller is also available for

Emergency manual mode independently of the microcontroller.

Manual mode is activated via the Manual menu to enable adjustment of a continuous controller output

of the 1st controller or to adjust a controller output of the 2nd controller. This menu can only be activated in

Manual mode, following the operational display.

Outputs are adjusted immediately. The percentage output value of a analogue output is altered from its

current value in accordance with the value entered by the user and is output directly. The switching output

on the 2nd controller is adjusted for as long as the button remains depressed.

Operational display Setpoint menu Password menu

Menu selection in Manual / Emergency manual mode

alternate

each second

Manual menu

Entry selection Abort

Value+1

to output

Linear output

adjust

1st controller

Switching or linear output

Value-1

to output

Emergency manual

adjust

with

2nd controller

Switching or linear output

Switching output

adjust

Pleiger Elektronik

GmbH & Co. KG

Edition: 6/2007 Subject to modifications Manual for 362MC Page: 9

5 Commissioning extension

The menu selection option of the 362MC can be extended for the purposes of commissioning the con-

troller. The extended functions for altering the configuration or parameterisation are available in both

Automatic and Manual / Emergency manual mode. The menu extension is accessible after entering the

password. This password lock serves to provide protection against unauthorised use.

5.0 Password entry

If no password has been entered (PW-lock=On), the password lock will be deactivated

to enable access to the extended commissioning menu by entering the currently valid password.

To this end, digits 1 to 4 have to be set to the stored

value for the password, in each case beginning from a

value of 0.

After input of the 4th digit, shown in the example here as password 1234, the value is compared against

the stored password. If the entered value corresponds to the stored password, the password lock will be

deactivated (PW-lock=Off); if the entered value does not correspond to the stored password, the pass-

word lock will remain active.

The password status is retained when the voltage supply for the controller is switched on and off.

On delivery, the password 0362 is stored for the 362MC.

Please alter this password to protect your specific settings.

Setpoint menu Password menu

Abort

Value+1

Value-1

Digit 1

Value entry

Value+1

Value-1

Digit 2

Value entry

Value+1

Value-1

Digit 3

Value entry

Value+1

Value-1

Digit 4

Value entry

compare

value

(example)

Pleiger Elektronik

GmbH & Co. KG

Page: 10 Manual for 362MC Edition: 6/2007 Subject to modifications

When the password entry function is selected while the password lock is deactivated (PW-lock=Off), the

password lock can be activated again or the stored password can be altered.

Activation of the password lock

When this function is selected, the current status:

password lock OFF or password lock ON, is shown in the

2nd line of the display. On activation of the password lock,

the system exits the commissioningmenu again.

Changing the password

A new password is selected and

entered as already described in

detail under ‘Password entry’.

Any number >=0000 and <=9999 is

permissible as the value for the

password.

Display menu

Abord

Activation of the password lock

Password

lock

OFF

Password

lock

Value+1

Value-1

Digit 1

Value entry

Digit 2 to 4

Value entry

save

new

password

Changing the

password

Password menu

Altri manuali per 362MC

Indice

Altri manuali pleiger Controllori

pleiger

pleiger 362MC Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente