PLUSOPTIX P12 Manuale utente
Seite 1/7
Wireless label printer
“plusoptiX P12“
With following Plusoptix instruments, labels can be printed with “plusoptiX P12“:
Mobile Pediatric Autorefractor plusoptiX A12C and A12R
Mobile Vision Screener plusoptiX S12C and S12R
Pediatric Autorefractor plusoptiX A16
Vision Screener plusoptiX S16
User manual
Version: 12.04.2017
Plusoptix GmbH
Neumeyerstrasse 48
90411 Nuremberg
Germany
www.plusoptix.com
Englisch
Seite 2/7
Please read this user manual before using the “plusoptiX P12” for the first time! It
explains how the device functions.
Table of contents
1. Description..................................................................................................................... 3
2. Checking scope of supply............................................................................................... 4
3. Inserting and charging rechargeable batteries................................................................ 4
4. Inserting paper............................................................................................................... 5
5. Switching printer on and off............................................................................................ 5
6. Printing........................................................................................................................... 6
7. Cleaning......................................................................................................................... 6
8. Technical details............................................................................................................. 7
List of figures
Figure 1: Top of “plusoptiX P12“............................................................................................ 3
Figure 2: Bottom of “plusoptiX P12“....................................................................................... 4
Figure 3: Open cover and insert paper.................................................................................. 5
Figure 4: Cleaning the “plusoptiX P12“ .................................................................................. 6
Seite 3/7
Description
The “plusoptiX P12“ is a wireless, battery-operated thermal printer with infrared interface. It is
not included in the scope of delivery and has to be ordered separately.
Attention:
The printer drivers are pre-installed on all “plusoptiX 12”devices from the
supplement “01D” in the serial number (Example: S/N 120xS-01D-xxxx xxxx).
Because of the technical design, devices with older serial numbers are not
compatible. There are no limitations in “plusoptiX 16”devices.
Following switching-on, the status lamp flashes green and the printer is ready
for operation. If it does not flash, the rechargeable batteries have to be
charged (see "Inserting and charging rechargeable batteries").
If the status lamp flashes red, the paper compartment is not properly closed or
a new roll of paper has to be inserted.
If the blue control lamp in the infrared receiver is illuminated, data is received
by the Plusoptix device.
If the red control lamp is illuminated, the rechargeable batteries are being
charged.
12V connection
On button
Paper
compartment
unlocking lever
Status lamp
Infrared reciever
Off button
Paper
compartment cover
Figure 1: Top of “plusoptiX P12“
Seite 4/7
1. Checking scope of supply
The scope of delivery includes the “plusoptiX P12“, four rechargeable Nickel-metal hydride
NiMH/AA HR6 batteries and a roll of self-adhesive labels.
For charging the batteries, use the medical power supply MES30B-3P1J. That is
the same power supply that is also used for charging the batteries of the
Plusoptix device.
2. Inserting and charging rechargeable batteries
Attention:
If you insert batteries other than those supplied, you should exclusively use
rechargeable Nickel Metal Hydride NiMH/AA HR6 batteries with a capacity of at
least 1900 mAh and a quick-charge rate of min. 1 A.
Figure 2: Bottom of “plusoptiX P12“
Inserting the batteries:
- Place the top side of the printer on a flat working surface
- Then remove the battery compartment cover with a 1-Cent coin and
- Insert the supplied batteries.
Note:
Ensure when inserting the rechargeable batteries, that the plus and minus battery
contacts are at the correct side. If you insert one or more batteries incorrectly by
mistake, the printer will not switch on.
Charging the rechargeable batteries:
Attention:
For charging the rechargeable batteries, exclusively use the power supply
MES30B-3P1J supplied with your Plusoptix device.
+
- + -
- + -
- + -
+
- + -
Battery compartment
Type plate
Seite 5/7
To charge the batteries use the medical power supply unit MES30B-3P1J. This is the same
power supply unit that is also used to charge the batteries of the Plusoptix device.
Once you have inserted the batteries, close the cover of the battery compartment and place
the printer in front of you. Now connect the medical power supply with the power cable to the
power socket and check if it is live (the green LED on the top of the medical power supply is
on). Following this, connect the medical power supply to the printer.
The inserted batteries are now automatically charged. During the charging process, the red
control lamp in the infrared receiver is on. The maximum battery charging time of the
supplied batteries is 4.5 hours.
3. Inserting paper
Open the paper compartment by slightly lifting the unlocking lever on the paper compartment
cover.
Figure 3: Open cover and insert paper
Unwind a little paper from the roll, so that approx. 1 inch protrudes from the paper
compartment. Ensure that the paper layers remain tightly wrapped about the roll core. Then
place the paper roll in the paper compartment as shown. After this, close the cover of the
paper compartment by pressing down on the cover. The cover engages audibly.
Note:
Use only original paper available from Plusoptix or a Plusoptix authorised dealer.
4. Switching printer on and off
To switch on, briefly press the On button. The printer starts immediately and is ready for
operation as soon as the status lamp flashes green.
When not used, the printer automatically switches off after approximately 10 minutes. To
switch it off manually, keep the Off button depressed for 3 seconds.
Seite 6/7
5. Printing
After each measurement with the Plusoptix device, any number of labels for documenting the
measurement results can be printed out. To do so, align the Plusoptix device with the
infrared receiver of the printer. The distance between Plusoptix device and the printer should
be approximately 1 m (3,28 ft). As soon as you touch the printer symbol on the screen of the
Plusoptix device, the data is transmitted and a label is printed out. To confirm the
transmission, a blue control lamp lights up in the infrared receiver. Keep the device directed
at the printer until the blue control lamp turns off.
Note:
If the infrared transmission is interrupted during a printing order the print-out of
the label is also interrupted. To obtain a complete print-out a new printing order
has to be sent.
6. Cleaning
If the print quality should deteriorate it is necessary to clean the printing head, paper sensor,
tear-off edge and drive roller. To do so:
- Open the cover of the paper compartment and remove the paper roll.
- If paper dust has accumulated in the paper compartment, clean it out with a vacuum
cleaner with fitted brush
- Clean the printing head and the drive roller with an ear bud lightly soaked in
isopropanol alcohol (IPA).
Printing head
Drive roller
Paper sensor
Tear-off edge
Figure 4: Cleaning the “plusoptiX P12“
Seite 7/7
7. Technical details
Attention:
For charging the rechargeable batteries, exclusively use the power supply
MES30B-3P1J supplied with your Plusoptix device.
Interface
IR-receiver
Storage
Temperature
0 to +50°C
Humidity
10 to 80% non-condensing
Operation
Temperature
+10 to +50°C
Humidity
20 to 80% non-condensing
Dimensions
Dimensions
159.6 x 89.6 x 45.6 mm
(6.28 x 3.53 x 1.8 in)
Weight
0.35 kg (12.35 oz)
Power supply
(MES30B-3P1J)
Input
110 to 240 VAC (50 to 60 Hz), 0.8 A
Output
12 VDC, 2.5A
Rechargeable batteries
(Panasonic BK –3MCCE 1,2V)
Type/Size
Nickel-metal hydride NiMH/AA HR6
Power/Quantity
1900 mAh/4 each
Altri manuali per P12
1
Indice
Altri manuali PLUSOPTIX Etichettatrice
