Politec PARVIS WS SMA Manuale utente

Technical

manual

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

INDEX

MAIN COMPONENTS

Pag. 3

ASSEMBLING THE CABLEPIT

Pag. 4



CABLE PIT POSITIONING

Pag. 6

BASE INSTALLATION ON CABLE PIT

Pag. 8

INSTALLATION EXAMPLES

Pag. 9

CONFIGURATION OF THE OPTICALS

Pag. 10



OPTICAL TX

Pag. 10

OPTICAL RX

Pag. 11

SANDOR WS SMA TX MOTHER BOARD

Pag. 12

SANDOR WS SMA RX MOTHER BOARD

Pag. 13

SETTINGS & FUNCTIONS

Pag. 14

DIP SWITCHES

Pag. 14

COLUMN ALIGNMETN

Pag. 15

CALIBRATION WITH SMA SYSTEM

Pag. 16

CALIBRATION WITH PARALLEL BEAMS

Pag. 20

ALARM SENSITIVITY ADJUSTMENT

Pag. 21

TECHNICAL CHARACTERISTICS

Pag. 22

F.A.Q.

Pag. 23

Installation recommendation

Verify that the beam tower is fully watertight once the cover and end caps have been correctly filled at the

end of the installation.

Use the cable glands supplied on the tower for all cabling must pass through the lower end cap using the

cable glands supplied. The missed used of proper accessories decrease the IP grade protection of the

tower.

Avoid any type of obstruction between the transmitter and receiver.

Avoid installing the receivers beams in a position where direct sunlight, at the same angle as the receivers

beams, can enter directly into optics especially at sunset and sunrise

Do not install multiple beams where the transmitter beam can interfere with other receiver beams. It is

always better place either transmitter or receivers back to back.

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

1.MAIN COMPONENTS



N°

Description

Aluminium pole

Pipe IR

Plug

Lamp adapter

Base

Cablepit

Motherboard TX

Group optic TX/RX

Motherboard RX

Cover for the base

Battery 3.6 V 19 Ah

Wireless trasmitter position

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

2.ASSEMBLING THE CABLEPIT

1. Insert the highlighted edge into other section and fix with screws

1. Insert the third section in the same way and fix with screws.

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

3. Enlarge the two opposite walls of cable pit to allow the positioning of last section.

1. Insert and well fix the missing screws.

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

CABLE PIT POSITIONING

The placement of the cable pit for PARVIS columns, after assembling, have to be done in the following way:

cement all around the cable pit keeping the top edge of it at same level of ground.

For PARVIS columns is also possible to keep the top edge ten centimeters below the level of the ground so that

it is visible only the IR tube.

This type of placement is possible only when the cable pit is fixed into the ground and not in a concrete

pavement.

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

POSSIBLE CORRECTION OF THE INCORRECT POSITIONING

Placement should be perpendicular to the ground. If the base is not in perfectly at ground level, is possible to

adjust it through the insert regulation of cable pit.

On the side that must be corrected loosen the insert in order to get the right inclination.

WRONG POSITIONING

CORRECT POSITIONING BY

ADJUSTING INSERTS

EXAMPLE

OF SETTING

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

3.BASE INSTALLATION ON CABLE PIT

Ensure that all the cables to and from the PARVIS tower passes through the supplied cable glands inserted into

the base cap. Use the central cable gland for lightning cable.

Base cover with the cable glands and O-ring

Once the cabling is completed the base cap has to be fixed to the base with relative O-ring.

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

4.INSTALLATION EXAMPLES

Per un’installazione a controllo di perimetro posizionare le barriere come indicato:

Note: if you use the optical sync do not place multiple transmitters on the same line in the same

direction

4 BEAMS

Simple barrier

8 BEAMS

Single barrier

8 BEAMS

Crossed barrier

POLITEC s.r.l. | Manual PARVIS WS SMA –Ver. 2.2

5.CONFIGURATION OF THE OPTICALS

OPTICAL TX

NB: The address settings as per default .

TX1

TX2

TX3

TX4

TX5

TX6

TEST LED

TAMPER

TEST

BUTTON

Indice

Altri manuali Politec Sistema di sicurezza

Politec

Politec SANDOR QUAD ESA SMA Manuale

Politec

Politec PARVIS MES SMA Series Manuale utente

Politec

Politec MANA MW Manuale

Politec

Politec ALES WS Manuale

Politec

Politec PARVIS MES SMA Manuale

Politec

Politec PARVIS HYBRID SMA Manuale utente

Politec

Politec ALES 60 Manuale utente

Politec

Politec ALES Series Manuale utente

Politec

Politec NAT SENSOR Manuale utente

Politec

Politec SANDOR DUAL SMA Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente