Poly-Control Danalock V3 Manuale utente
Poly-Control
Danalock V3
SKU: POLELOCKV3
Quickstart
This is a secure Door Lock for Europe. To run this device please insert fresh 4 * CR123A batteries. Please make sure the internal battery is fully
charged. To add this device to your network execute the following action:
Push the switch once.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart
section. (For more information about frequency regulations please refer to the frequency coverage overview at Sigma Designs Website ).
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication)
and every mains powered node can act as a repeater for other nodes (meshed network) in case the
receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-
Wave device regardless of brand and origin as long as both are suited for the same frequency
range.
If a device supports secure communication it will communicate with other devices secure as long as
this device provides the same or a higher level of security. Otherwise it will automatically turn into a
lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The Danalock is a doorlock with a integrated motor, which you place on the inside of your front door. You can control it with a smartphone (via Z-Wave
Gateway or directly via Bluetooth). The Danalock fits to every door with a mechanical Euro profile cylinder.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
Easy installation - without drilling holes
For the installation of the lock your existing cylinder is replaced by a Danalock cylinder and the doorlock with the motor will be attached to it.
Battery empty or Smartphone lost?
After the installation you can unlock the door with a physical key any longer. On the outside of the door you can use the key and inside you can lock/unlock
it manually.
Auto-Lock
Let the door lock automatically when you leave your home. The auto-lock-function locks the door automatically after a predefined time.
Properties:
Z-Wave Plus & Bluetooth Version
EU frequency: 868,42 MHz (Z-Wave)
Package content: 1x Danalock V3 incl. Batteries (without lock cylinder)
Power supply: 4x CR123
Battery lifetime: 6-12 month
torque: 1,5 Nm
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You
can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is
recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is
inoperable.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
The Danalock can be set to factory settings by pushing the switch ten times.
Safety Warning for Batteries
The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different
brands.
Installation
1. Remove the old cylinder
First you have to remove your current cylinder. Unscrew the lock-screw in the mortise-plate on the side of the door.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
2. Pull out the old cylinder
Insert your key and turn it so the cam lines up with the body of the cylinder. Now pull out the cylinder.
3. Adjust the new cylinder
Measure the back part (on the outside of your door) of the old cylinder from the middle of the screwhole and away (see illustration). In the Danalock box
you’ll nd an adjustable lock cylinder.
If the old cylinder and the adjustable cylinder matches - go to no 5. If they don’t please proceed.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
4. Unscrew the small screws on both sides of the cylinder and pull it apart.
5. Insert the same size of spacer piece and brass tube to make the adjustable cylinder match the old cylinder. Please look at the following size guide to find
the right length for the spacer piece and the brass tube.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
Size guide - When you adjust the size of the Danalock cylinder to the old cylinder you‘ll have to exchange the brass tube in the center with another that fits
the spacer piece. Here are the different combinations.
6. Assemble the cylinder and screw the small screws back in on both sides of the cylinder.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
7. Insert the adjustable cylinder
Insert the new cylinder, and re-insert the lock-screw in the mortise-plate to fix the cylinder. (b) Do not tighten the screw to hard - make sure the cylinder is
working by locking and unlocking with your hand.
8. The right rosette spacer
To avoid pulling the cylinder out of place you need to find the right spacer or a spacer combination between the rosette and the back plate. Unscrew the
two breakable screws that holds the spacers together with the adjustable cylinder. Choose one or more spacers so they flush with the rosette surface. (See
next illustration).
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
IMPORTANT! Avoid pulling the cylinder out of place. It is important that the spacer flushes or sticks out from the hole in the rosette plate.
9. Break the screws to the right length
Depending on which spacer or spacer combination you chose, it is now important that the screws that fasten the cylinder to the back plate have the right
length. Use this chart to find the right length.Use a wirecutter, two pliers or bend the screws forth and back several times in a vice to break them.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD
Indice
