Polycom Realpresence group convene Manuale utente

ENGLISH

www.polycom.com

sociated with Polycom’s products are trademarks and/or service marks of Polycom,

Inc. and are registered and/or common law marks in the United States and various

other countries. No portion hereof may be reproduced or transmitted in any form or

by any means, for any purpose other than the recipient’s personal use, without the

express written permission of Polycom.

P/no. MFL69143011 (1503-REV00)

Set Up the Polycom® RealPresence® Group Convene™

Display AC/DC adapter 4 AC Power

adapters

Stand body

Stand base Screws (4 pcs)

(M4 X L10)

Cable cover Rear cover

HDMI cable DC-to-DC jumper

cable

2 Screws and

2 T-Nuts

Easy Setup Guide

*MFL69143011*

ENGLISH

ASSEMBLE THE STAND

Use the packing material from the

lower portion of the display as a

platform for assembly.

Do not stand the unit up until the

installation and cabling are complete.

INSTALL THE CAMERA

Unpack the RealPresence Group Series co-

dec and camera. Reserve the codec power

supply for future use.

Power supply

Only use the power supply

provided with the display

accessory.

Open the hinge on the camera and insert the hinge into the camera

bracket on the rear top of the display.

Gather the excess cable and secure with the cable ties.

ENGLISH

ASSEMBLE THE STAND

Use the packing material from the

lower portion of the display as a

platform for assembly.

Do not stand the unit up until the

installation and cabling are complete.

INSTALL THE CAMERA

Open the hinge on the camera and insert the hinge into the camera

bracket on the rear top of the display.

Gather the excess cable and secure with the cable ties.

Do not carry display by holding the base.

Do not carry the display upside down by just holding the

base. This may cause the display to fall off the stand and

could result in personal injury.

ENGLISH

CONNECT CABLES

Plug the DC-to-DC jumper between the

display and the codec.

Connect and route all cables through the

cable management channel.

Note: Generic cables

If you use generic cables

not certied by LG and

Polycom, the screen may

not display or there may

be image noise.

INSTALL THE CODEC

Install the RealPresence Group Series codec by inserting the T-nuts into

the keyholes on the back of the display.

Connect the DC power, LAN, HDMI, and camera cables to the codec. Refer

to the RealPresence Group Series 500 Setup Sheet for details.

Route the LAN and DC power supply cables between the codec and dis-

play and then through the cable channel at the rear of the stand.

PREPARE THE CODEC

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

ENGLISH

CONNECT CABLES

INSTALL THE CODEC

Install the RealPresence Group Series codec by inserting the T-nuts into

the keyholes on the back of the display.

Connect the DC power, LAN, HDMI, and camera cables to the codec. Refer

to the RealPresence Group Series 500 Setup Sheet for details.

Route the LAN and DC power supply cables between the codec and dis-

play and then through the cable channel at the rear of the stand.

PREPARE THE CODEC

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

ENGLISH

Stand Hinge

Cable cover

MANAGE THE CABLES

Arrange the cables so that they run below the stand hinge and then cover

them with the cable cover from the bottom up.

You can disassemble the cable cover by following the assembly instruc-

tions in reverse order.

INSTALL THE REAR COVER

Install the rear cover on the stand by tting the hooks on the cover into

the slots on the back of the display and sliding into place.

ENGLISH

MANAGE THE CABLES

Arrange the cables so that they run below the stand hinge and then cover

them with the cable cover from the bottom up.

You can disassemble the cable cover by following the assembly instruc-

tions in reverse order.

INSTALL THE REAR COVER

Install the rear cover on the stand by tting the hooks on the cover into

the slots on the back of the display and sliding into place.

ENGLISH

CONNECT THE HEADPHONES (OPTIONAL)

CONNECT POWER

DC Switch

(shipped

with codec)

Caution: Power on DC switch rst.

Power on the DC switch on the bottom of the product

before turning on the display.

Four AC power adapter cables are supplied with the display. Select the ap-

propriate AC power adapter cable for your geographic region. Connect the

cable to the power supply input. Connect the AC power cable, provided

with the RealPresence Group Series codec, to the AC power adapter cable.

ENGLISH

CONNECT THE HEADPHONES (OPTIONAL)

Bottom Center of

the Display

CONNECT POWER

Four AC power adapter cables are supplied with the display. Select the ap-

propriate AC power adapter cable for your geographic region. Connect the

cable to the power supply input. Connect the AC power cable, provided

with the RealPresence Group Series codec, to the AC power adapter cable.

ENGLISH

Power/Menu buttons

POWER ON THE SYSTEM

Power on the display. When the Automatic Standby message appears,

select Yes to disable Automatic Standby. Otherwise, the display will go

into Automatic Power Down after four hours and it will not wake up for

a video call without manually turning on the display. When the codec

nishes booting up, refer to the Polycom RealPresence Group Series

Administrator Guide for details on codec settings conguration and IP

connectivity.

ADJUST THE ANGLE

Automatic Standby

Automatic Standby is currently set at 4 hours.

Would you like to disable Automatic Standby?

Yes No

Press "OK" button to select.

OK EXIT

Altri manuali per realpresence group convene

Indice

Altri manuali Polycom Sistema di conferenza

Polycom

Polycom MGC-100 Manuale utente

Polycom

Polycom Studio Manuale utente

Polycom

Polycom Real-Time Media Conferencing Platform RMX... Manuale utente

Polycom

Polycom V500 Manuale utente

Polycom

Polycom 7000E Manuale utente

Polycom

Polycom Price Center 451 Manuale utente

Polycom

Polycom CX5500 Manuale utente

Polycom

Polycom VVX 500 Manuale utente

Polycom

Polycom EagleEye Director II Manuale

Polycom

Polycom RealPresence Group 300 Istruzioni per il montaggio

Polycom

Polycom 1725-22886-001/A Manuale utente

Polycom

Polycom SIP 2.2.2 Manuale utente

Polycom

Polycom QDX 6000 System Come usare

Polycom

Polycom HDX Desktop Systems Guida di riferimento rapido

Polycom

Polycom QSX Manuale di servizio

Polycom

Polycom MGC+100 ReadiConvene Guida all'installazione

Polycom

Polycom Vortex Series Supplemento

Polycom

Polycom 3150-16966-002 Manuale utente

Polycom

Polycom VSX Series Manuale utente

Polycom

Polycom VSX VSX 6000 Istruzioni utente

Polycom

Polycom RMX 2000 Scheda tecnica

Polycom

Polycom G7500 Manuale utente

Polycom

Polycom RealPresence Video Protect 500 Manuale

Polycom

Polycom VIEWSTATION EX Manuale utente

Manuali Sistema di conferenza popolari di altre marche

Kramer

Kramer VIA GO Manuale utente

AVT

AVT MAGIC AC1 Go Manuale utente

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuale utente

Sony

Sony PCS-I150 Manuale utente

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuale utente

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guida

Speakerbus

Speakerbus iD 712 Manuale utente

Trelleborg

Trelleborg SafePilot CAT PRO Manuale utente

Sennheiser

Sennheiser ADN Manuale utente

ADTRAN

ADTRAN NetVanta 7100 Manuale utente

AINA

AINA PTT Voice Responder Manuale utente

Yamaha

Yamaha ProjectPhone PJP-100H Manuale utente

vissonic

vissonic VLI Series Manuale utente

Panasonic

Panasonic KX-VC500 Manuale utente

Poly

Poly Trio 8300 Manuale utente

Crestron

Crestron Mercury CCS-UCA-SMK Disegno dimensionale

Inmarsat

Inmarsat mini M Manuale utente

Tenveo

Tenveo ALL-IN-ONE Manuale utente

Polycom realpresence group convene Manuale utente

Manuali Sistema di conferenza popolari di altre marche