Polypipe SmartStat Manuale utente
SmartStat
1
Model: SmartStat
Smart Series
2
Table of Contents
1
2
3-4
5-6
7
8
8-9
9
9
Product Image
Table of Contents
What is a Programmable
Room Thermostat?
Installation Procedure
Mode Select
Pairing the SmartHub
Pairing the SmartStat
What is a Mesh Network?
Approach Sensor
34-35
36
37
38
38
39
LCD Display
Setting the Switching Times
Timer Override
Optional Features
Optional Features Table
Time Clock Mode Wiring Diagram
Mode 2 - Time Clock
LCD Display
Temperature Display
Setting the Clock
Setting the Comfort Levels
Setting the Temperature
Temperature Hold
Locking/Unlocking the neoStat
3410
Mode 1 - Thermostat
11-12
13
14
15-16
17
18
19
Frost Protection
Power ON/OFF
Holiday Programming
Optional Features
Re-calibrating the Thermostat
Error Codes
Floor Temp Sensor Probe Type
Diagrams
Factory Reset
20
21
22
23-26
27
27
28
29-32
33
SmartStat
3
What is a Programmable Room Thermostat?
A programmable room thermostat is both a programmer and a room thermostat.
A programmer allows you to set “On”and “O” periods to suit your own lifestyle.
A room thermostat works by sensing the air temperature, switching on the heating
when the air temperature falls below the thermostat setting, and switching it o once
this set temperature has been reached.
So a programmable room thermostat lets you choose what times you want the heating
to be on, and what temperature it should reach while it is on. It will allow you to select
dierent temperatures in your home at dierent times of the day (and days of the week)
to meet your particular needs and preferences.
Setting a programmable room thermostat to a higher temperature will not make the
room heat up any faster. How quickly the room heats up depends on the design and
size of the heating system.
Similarly reducing the temperature setting does not aect how quickly the room cools
down. Setting a programmable room thermostat to a lower temperature will result in
the room being controlled at a lower temperature, and saves energy.
Smart Series
4
The way to set and use your programmable room thermostat is to nd the lowest
temperature settings that you are comfortable with at the dierent times you have
chosen, and then leave it alone to do its job.
The best way to do this is to set the room thermostat to a low temperature
– say 18°C , and then turn it up by 1°C each day until you are comfortable with the
temperature. You won’t have to adjust the thermostat further. Any adjustment above
this setting will waste energy and cost you more money.
You are able to temporarily adjust the heating program by overriding or using the
temperature hold feature. These features are explained further on pages 17 and 18
of this manual.
Programmable room thermostats need a free ow of air to sense the temperature,
so they must not be covered by curtains or blocked by furniture. Nearby electric
res, televisions, wall or table lamps may also prevent the thermostat from working
properly.
SmartStat
5
Installation Procedure
The SmartStat is designed to be ush mounted and requires a back box of 35mm
(minimum depth) to be sunk into the wall prior to installation.
Step 1
Using a small screwdriver, slightly loosen the screw from the bottom face of
the thermostat. Then carefully separate the front half from the back plate.
Step 2
Place the thermostat front somewhere safe.
Terminate the thermostat as shown in the diagrams on pages 28-31 of this booklet.
Note: For time clock wiring connections, terminate as shown on page 38.
Step 3
Screw the thermostat back plate securely into the back box.
Step 4
Clip the front of the thermostat onto the back plate, securing it in place with the
retaining screw.
Do
Mount the thermostat at eye level.
Read the instructions fully so you get the best from our product.
Don’t
Do not install near to a direct heat source as this will aect functionality.
Do not push hard on the LCD screen as this may cause irreparable damage.
Smart Series
6
1 2
3 4
SmartStat
7
SmartStat can either be used as a thermostat or a time clock.
Thermostat mode is the default setting.
To change between thermostat or time clock modes, follow these steps.
• Use the Left / Right keys to scroll to ...........................................................................
• Press and hold the Tick button for 3 seconds ...............................................................
• SETUP will be highlighted, now press and hold the tick key for 10 seconds.....
• Use the Left / Right keys to scroll between modes .....................................................
Mode 1 = Thermostat
Mode 2 = Time Clock
• Press the Tick key to conrm selection............................................................................
The SmartStat will revert to the main display screen for the selected mode.
For time clock mode instructions, rst pair the time clock with the SmartHub as
explained on page 8, then turn to page 33.
Mode Select
Smart Series
8
The next step is to join the SmartStat to the Hub, we recommend joining the
thermostat located nearest to the SmartHub rst.
To add a SmartStat, follow these steps;
• In the app, select ADD ZONE, enter a preset or custom title, thenpress NEXT.
• You now have two minutes to join the thermostat to the Hub.
• On the SmartStat, use the Left / Right keys to select , press and hold Tick............
• SETUP will be highlighted, now press the tick key once .....................................................
• Feature 01 is displayed on screen.
Pairing the SmartStat
Pairing the SmartHub
To pair the SmartHub with the Polypipe Smart App, follow these steps.
• Connect the Hub to your router with the Ethernet cable provided.
• Connect the power supply to the neoHub.
• The router will automatically assign an IP address to the Hub, the Link LED
will light up RED once the SmartHub has connected to your network.
• Once connected to the cloudserver, the Link LED will turn GREEN.
• Connect your smartphone or tablet device to the same WiFi network as your router.
• Download the FREE Polypipe SmartApp from the Apple App Store or Google Play Store
and register an account.
• Once you have registered your account, press Sign In, then press Add Location.
• Pressthe connect button on the SmartHub to add the location to your account.
• When successfully connected, enter a title for the location (e.g. Home).
SmartStat
9
What is a Mesh Network
Approach Sensor
SmartStat works using a mesh network, meaning SmartStats have the ability
to send & receive signals via other thermostats on the network. This signal is relayed
from one thermostat to another until it reaches its destination. This communication
method extends the communication range whilst oering increased network stability
when compared with standard RF thermostats.
The Mesh symbol is shown when the device is communicating with the Hub, if the
mesh symbol disappears this indicates connection to the SmartHub has been lost.
The SmartStat uses proximity to detect when you are about to use the touch
keys. As you approach the thermostat, the touch keys and backlight will light up.
This can be useful if you need to adjust the set temp or timer in a dark room.
• Press the Tick key once again to pair the thermostat to the Hub....................
• The MESH symbol appears ashing on the display.
• When the SmartStat successfully connects to the Hub the
MESH symbol will be permanently displayed.
• Press ADD ANOTHER for addtional zones or press FINISH to complete setup.
Please note, you only have to pair the hub to your account once.
To pair any additional Smart Stat, select ZONES, edit, then ADD ZONE.
Smart Series
Indice
Altri manuali Polypipe Termostato
