PoolRite Xtreme Chlorinator Manuale utente
Manufactured by Aussie Chlorinators
For more details refer to the back of Power Pack
For user manual and warranty details refer
to www.poolrite.com or scan the QR code
SALT MODE
MENU
ENTER
Operating salt level for the XTreme Chlorinator
Mineral Salts 3500-4000ppm | Sodium salts 3500-7000ppm
ON
OFF
A. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and maintenance shall not be made by children without
supervision.
B. The appliance must be permanently connected to xed wiring according to the
national wiring rules. The appliance must be installed, maintained and serviced by a
qualied licensed electrician. Equipotential bonding must be carried out.
C. Means of disconnection from the supply mains having a contact separation in all
poles that provide full disconnection under over voltage category Ill conditions must
be incorporated in the xed wiring in accordance with the wiring rules.
D. The appliance should be supplied through a residual current device RCD having a
rated residual operating current not exceeding 30ma.
E. Parts containing live parts, except parts supplied with safety extra-low voltage not
exceeding 12V, must be inaccessible to a person, in the bath or spa.
F. Parts incorporating electrical components, except remote control devices, must be
located or xed so that they cannot fall into the bath or spa.
G. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied person in order to avoid a hazard.
Statement
2
2 STATEMENT
3 INDEX
4 INSTALLATION
5 PLUMBING
6 CONTROLS
7 MENU & SUB MENU
8 MODES
9 BACKWASH
10 SALT
11 WATER QUALITY
12 TROUBLESHOOTING
13 TROUBLESHOOTING
14 TROUBLESHOOTING
15 SPECIFICATION TABLE
16 PARTS
17 WARRANTY
18 NOTES
20 CONTACT DETAILS
Index
3
Plumbing should be performed by a qualied Plumber or a pool industry service technician
where possible. It can however be done by the home handyman taking due care and
attention.
Warning: Do Not apply Priming Fluid to the Clear Cell Housing
All pipe work should be primed with priming uid before glue is applied, any high
pressure PVC glue will work, make sure both surfaces are well coated before mating the
connections as you will only have a few seconds before the glue bond will take.
Piping from the Filter to the Cell should enter the pipe connection closest to the cell head
as per the image below as this is where the water sense probe has been installed during
manufacture. NOTE: When plumbed from the other direction and used with variable
speed pumps having very low ow rates the water probe may not get covered with water
causing the chlorinator to display Priming Cell.
Plumbing
Salt Cell
Chlorinator
Filter
Pump
Optional
Return To
Pool Using
Outlet 1or 2
2
1
4
A. Position the chlorinator power module at least 1m above ground and at least 2m from
the pool edge.
B. Mount the stainless steel bracket to a solid structure with the screws provided and t
the power module over the two raised pins on the bracket, secure with the 2 locking
clips provided.
C. Protect the chlorinator module and cell housing from direct sunlight and rain where
possible for extended life.
D. Connect the mains plug from the chlorinator power pack into a RCD Protected 240V
mains 10A outlet.
E. Connect the cell cable connector into the connector on the bottom of the power pack.
F. Connect the mains plug from the pump into the pump outlet on the bottom of the
chlorinator power pack.
Installation
5
Controls
Toggles the chlorinator OFF then back ON when connected to the mains
power
Press to enter or exit the main menu or to exit sub menus (PAGE 7)
Press to enter a selected menu or conrm a setting
Selects different modes of operation, (PAGE 8)
Press to select
»ON
»TIMER
»SUPERCHLORINATE
»BOOST
»SPA
»BACKWASH
Will turn the pump ON and measure your salt or mineral
(PAGE 10)
Increase button is used to navigate menus, modify settings or increase the
chlorine output
Decrease button is used to navigate menus, modify settings or decrease the
chlorine output
6
MENU
SUB MENU
Pressing the MENU button will take you into the main menu list, by using the up/down
arrows you can scroll through the list, then press the enter button to enter the function you
wish to modify, pressing the MENU button again will exit you from the sub menu
CLOCK Use the up/down buttons to enter the time of day (0-24hrs)
CHLORINE
OUTPUT
Use the up/down buttons to set the chlorine output, this can also be
performed from the working screen as the chlorinator is functioning
TIMER Use the up/down buttons to move the cursor above or below each
block where you would like the chlorinator & pump, or pump only to
operate, then by pressing the enter button you can toggle between
No operation
‘C’ Chlorinator & pump operation
‘P’ Pump only operation
PUMP
PROTECTION
Use the up/down buttons to set between 3-10 minutes or you can set
this function OFF. Pump protection is activated when there’s no water
owing across the cell/electrode
CELL
CLEANING
Use the up/down buttons to change the time between cell reversals, a
shorter time will remove more calcium for pools that have high levels,
set for a longer time for pools that don’t have calcium issue’s (long
reversal times will extend cell life, see page 12, CELL LIFE)
BRIGHTNESS If your screen is too bright for the area installed you can dim the
backlight with the up/down buttons
SYSTEM INFO TOTAL HRS Hours the power module has operated
CELL HRS Hours the cell has operated
POLARITY What direction the electrical current is owing
UNIT SIZE Unit size of your chlorinator
SW VERSION Software version
7
Pressing the MODE button will toggle you through the different operational modes the
chlorinator can be set too.
These MODES are:
ON
Sets the chlorinator and pump to operate 24/7
TIMER
Sets the chlorinator and pump or pump only to operate at the timer blocks that have been
set
SUPER CHLORINATE
Sets the chlorinator and pump to operate @100% for 24hrs only, then will automatically
revert back to TIMER mode
BOOST
Sets the chlorinator and pump to operate for 6hrs then will automatically revert back to
TIMER mode
SPA
Sets the chlorinator to operate @ 10% output and pump on NOTE: This mode will operate
24/7 until you manually set the chlorinator mode back to TIMER
BACKWASH
Backwash is explained on (PAGE 9)
Mode
8
The Backwash function has been added to simplify how the pump is operated as you
adjust the Filter Lever into its different positions during a backwash.
NOTE: NEVER OPERATE THE FILTER LEVER WHILE THE PUMP IS OPERATING
WARNING: THE PUMP WILL START AND STOP AUTOMATICALLY
Enter the BACKWASH function by pressing the MODE button until BACKWASH is displayed
The screen will now display ..... SET VALVE TO BACKWASH AND PRESS ENTER ..... rotate
the lter valve to backwash, pressing enter will start the pump and you will see the dirty
water exit the waste pipe and in the clear glass installed on your lter.
The screen will now display ..... PRESS ENTER TO FINISH BACKWASH ...... press enter
once the water in the waste pipe has become clear, this will stop the pump so you can
rotate the lter valve.
Chlorinator will now display ..... SET VALVE TO RINSE AND PRESS ENTER ..... rotate
the lter valve to RINSE, pressing enter will start the pump, once water is owing
allow the pump to operate for at least 30 seconds or as per the lter manufacturers
recommendations to clean the last contaminates from the lter.
Chlorinator will now display ..... PRESS ENTER TO FINISH RINSE CYCLE.. ... press enter, the
chlorinator will display ...... SET VALVE TO FILTER AND PRESS ENTER .... press enter, the
backwash is now complete and the chlorinator will automatically revert back to the TIMER
mode.
Backwash
9
Recommended Salt Concentration
For Sodium Chloride Salts 3500 - 7000 PPM
For Mineral/Magnesium Chloride Salts 3500 - 4000 PPM
Pressing the SALT button will start the salt measurement, the chlorinator will start the
pump as the measurement requires good water ow through the cell, this also allows the
water temperature to be taken as it forms part of the equation.
Water temperature at the cell should be allowed to stabilize for at least 5 minutes before a
measurement is taken
The measurement will take approx 30 seconds and display a result in PPM, the result will
continue to be updated every few seconds over 1 minute then revert back to the previous
mode automatically or by pressing SALT will cancel the salt test.
Salt levels under 2000ppm cannot be measured by the chlorinator and salt levels above
8000ppm will be more inaccurate.
PLEASE NOTE:
The salt measurement is meant to be a guide only as many
factors will vary the result, for more accurate measurements a
sample of pool water should be taken to your local pool shop or
be performed by your local pool service technician.
Salt
10
Indice
Altri manuali PoolRite Filtro per piscina
Manuali Filtro per piscina popolari di altre marche
Davey
Davey EcoPure DEP2140 Manuale utente
JUWEL Aquarium
JUWEL Aquarium EccoSkim Manuale utente
POLYGROUP LIMITED
POLYGROUP LIMITED SFS600 Filter System with F600C Pump Manuale utente
Pentair Pool Products
Pentair Pool Products Filter CFW Series Manuale utente
Oase
Oase Skimmer 250 Manuale utente
Oase
Oase CrystalSkim 350 Manuale utente