POS-X XPC500 Manuale utente
TouchKit Manual for WinCE v2.0.9 0
TouchKit
TouchScreen Controller
User Manual
for Windows CE
Version: 2.0.9
TouchKit Manual for WinCE v2.0.9 1
CONTENT
CHAPTER 1. TOUCH PANEL CONTROLLER...........................................................2
1.1 CONTROLLER..................................................................................................................................... 2
1.2 SPECIFICATIONS AND FEATURES........................................................................................................ 2
CHAPTER 2. INSTALLING TOUCHKIT......................................................................4
2.1 FOR WINDOWS CE 2.12 /3.0 ............................................................................................................. 4
2.2 FOR WINDOWS CE.NETSTYLUS....................................................................................................... 5
2.3 FOR WINDOWS CE.NETAND CE 5.0............................................................................................... 14
CHAPTER 3. CONFIGURATION UTILITY AND RIGHT BUTTON EMULATOR.....17
3.1 FOR WINDOWS CE 2.12 /3.0 ........................................................................................................... 17
3.2 FOR WINDOWS CE.NET.................................................................................................................. 20
TouchKit Manual for WinCE v2.0.9 2
Chapter 1. Touch Panel Controller
This touch panel controller provides the optimal performance of analog resistive
touch panels for 5 wire model. It communicates with PC system directly through
RS232, PS/2 or USB connector. Users can see how superior the design is in
sensitivity, accuracy and friendly operation. The touch panel driver emulates mouse
left and right button function and supports operating systems including Microsoft
Windows 95 / 98 / ME / NT4 / 2000 / XP / XP Tablet PC Edition, Windows CE 2.12 /
3.0 / .NET, Linux, iMac and DOS.
1.1 Controller
Interface RS232 USB PS/2
5-wire Ready Ready Ready
Table 1. Controllers match with different interfaces
1.2 Specifications and Features
Specifications
Power requirements +5VDC ( Maximum 100mA, typical 70mA,
50mV peak to peak maximum ripple )
Operating temperature 0 to 50
Storage Temperature -40 to 80
Relative Humidity 95% at 60
Protocol RS232 Model: 9600 bauds, None parity, 8 data bits
and 1 stop bit
USB Model: USB 1.1 Low speed
PS/2 Model: PS/2 mouse
Resolution 2048 X 2048
Report rate RS232 Model: Max. 160 points/sec
USB Model: Max. 160 points/sec
PS/2 Model: Max. 140 points/sec
Response time Resistive: Max. 35 ms
Capacitive: Max. 20 ms
Pin out definition 5 wire model: UL, UR, COM, LR, LL
Panel resistance 5 wire resistive model: 50 ~ 200 ohm
( pin to pin on drive layer )
Regulatory Approvals FCC-B, CE
TouchKit Manual for WinCE v2.0.9 3
Table 2. Specifications for TouchKit controller
Features
Calibration Fast full 4 point positioning
Compensation Accuracy 25 points linearity compensation.
Draw Test Position and linearity verification
Language Support 10 languages for Windows
Advanced Feature 1. Support monitor / display rotation
2. Support multiple monitor / display
3. Support QVGA and Half-VGA function
4. Support edge compensation
5. Support constant touch
Controller Setting 1. Support multiple controllers
2. Dynamical add / remove controllers
3. Change Controller interface without reboot.
Mouse Emulator 1. Right / Left button emulation
2. Normal / Click on touch / Click on release mode
3. Auto right button
Sound Notification 1. Sound option (No Sound / Touch Down / Lift Up)
2. Frequency adjustment
3. Duration adjustment
Double Click 1. Configurable double click speed
2. Configurable double click area
OS support 1. Windows 95 / 98 / ME / NT4 / 2000 / XP /
Windows XP Tablet PC Edition
2. Windows CE 2.12 / 3.0 / .NET
3. Linux ( RedHat / Fedora / Mandrake /
Suse / YellowDog )
4. iMac. OS9.x / OSX
5. MS-DOS:
Support display resolution:
320x200, 640x200, 640x350, 640x480, 800x600,
1024x768 and 1280x1024
COM port support 1. Support COM 1 ~ COM 256 for Windows and
Linux
2. Support COM 1 ~ COM 8 for DOS
Table 3. Features for TouchKit software
TouchKit Manual for WinCE v2.0.9 4
Chapter 2. Installing TouchKit
TouchKit is software, which contains drivers, configuration and right button utilities of
the touch panel controllers for RS232 and USB on x86 CPU and Windows CE
operation system.
The two utilities are as follows:
•Configuration support
The calibration and draw test of touch panel are done by this support.
•Right button support
This utility is for emulating the right and left button of mouse through controlling
touch panel. Users can toggle between right or left mouse buttons by this utility.
2.1 For Windows CE 2.12 / 3.0
There are a total of five files in the TouchKit for Windows CE directory.
Follow these steps to install TouchKit for Windows CE.
TouchKit.dll - driver
Touch32ex.dll - specific dynamic linking library
TouchTray.exe - right mouse support
TouchKit.exe - Configuration Utility
TouchKit.reg - information that will be added to registry
1. Make sure that Windows CE has the serial ports drivers.
2. While building Windows CE, users have to assign TouchKit.dll, Touch32ex.dll,
TouchTry.exe and Touchkit.exe to the appropriate directory.
3. Add some registry value the content of TouchKit.reg.
4. Now, install Windows CE with these touch panel driver and utilities.
Note: TouchTray.exe is the file of the Right Mouse Utility. It has to be started during
computer booting. So, put this file to appropriate directory to satisfy this specific
request.
Users can boot this Windows CE version on specific device. The right mouse button
utility will be emulated while computer booting and the touch panel driver is also
ready.
TouchKit Manual for WinCE v2.0.9 5
2.2 For Windows CE.NET Stylus
There are two driver package versions and showed as below:
CE.NET bundle calibration utility
Stylus dedicated configuration utility.
USB interface driver installation with CE.NET bundle calibration utility. File
List:
USBPort.dll - USB touch screen driver
Touchp.dll - USB touch screen driver
Calibration.exe -a calibration program (Programmer could choose
the path while building the image of CE platform. This program is not
necessary for CE.NET)
Note: Select the UHCI or OHCI USB Host Controller driver for the platform,
which is supported by the target device, and check the USB mouse can go
to the same port.
Select the Touch Display [stylus] on the platform. Users can see:
“Catalog\Core OS\Display based devices\Shell and User Interface\Touch
Display[Stylus]”
Select the Mouse on the platform. Users can see:
“Catalog\Core OS\Display based devices\Shell and User Interface\Mouse”
TouchKit Manual for WinCE v2.0.9 6
1. Create a sub-folder “CEDB” under C:\
2. Copy files USBPort.dll and Touchp.dll to the directory.
3. Launch platform builder and open the platform workspace.
4. Edit the PROJECT.BIB in the Parameter View of Platform Builder.
5. Add these two lines in Modules:
usbport.dll C:\CEDB\usbport.dll NK SH
touchp.dll C:\CEDB\touchp.dll NK SH
TouchKit Manual for WinCE v2.0.9 7
6. Edit the PROJECT.REG in the Parameter View of Platform Builder.
7. Add these lines for registry:
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\TOUCH]
“DriverName”=”Touchp.dll”
“CalibrationData”=”102,102 1945, 102 1945,1945 102,1945”
“BCLEFT”=dword:64
“BCRIGHT”=dword:64
“BCTOP”=dword:64
“BCBOTTOM”=dword:64
Then copy the following sentences to the PROJECT.REG
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\14371_1\0_0_0\255
_255_255\USB_TOUCH_Driver]
“DLL”=”USBPort.dll”
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\14371_2\0_0_0\255
_255_255\USB_TOUCH_Driver]
“DLL”=”USBPort.dll”
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\4660_1\0_0_0\255_
255_255\USB_TOUCH_Driver]
“DLL”=”USBPort.dll”
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\3823_1\0_0_0\255_
255_255\USB_TOUCH_Driver]
“DLL”=”USBPort.dll”
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients3823_2\0_0_0\255_
255_255\USB_TOUCH_Driver]
“DLL”=”USBPort.dll”
TouchKit Manual for WinCE v2.0.9 8
8. After building the image of CE.NET and loading it to the hardware
platform. Users can use the stylus to do the calibration, which can be
found in the control panel.
TouchKit Manual for WinCE v2.0.9 9
9. To keep the calibration data after WINCE reboot, please write WINCE
REGISTRY to FLASH or other storage on target.
RS232 interface driver installation with CE.NET bundle calibration utility. File
List: Touchp.dll - RS232 touch screen driver
Calibration.exe -A calibration program (Programmer could choose
the path while building the image of CE platform. This program is not
necessary for CE.NET)
Note:
Altri manuali per XPC500
1
Questo manuale è adatto per i seguenti modelli
2
Indice
