POSEIDON 1133 Guida all'installazione

CYKLON

1.0:E48

REPAIR INSTRUCTIONS SECOND STAGE DEMAND VALVE

EXPLODED VIEW

SECOND STAGE 1133 Low pressure hose

Low pressure valve

Mouth-piece

Mouth-piece tube

Diaphram house

CYKLON

1.0:E49

SECOND STAGE

1133, 3224, 3354, 3536

Removal:

1. Disconnect the low pressure

hose from the second stage

with a 17 mm. open wrench.

Remove the oring (2) with an

o-rings remover.

2. Remove the diaphragm housing

(27) from the mouth piece tube.

3. To release the exhalation cover,

remove the locking ring with a

small screwdriver.

4. Remove the exhalation

diaphragm (21).

CYKLON

1.0:E50

1. Remove the locking ring (25)

with an awl. Support the

diaphragm house, see diagram.

Make sure that the sealing

surface for the exhalation

diaphragm is not damaged.

2. Remove the cover (24) and the

inhalation diaphragm (23).

Removal: Push out the purge

button

IMPORTANT! The purge button

(26) should not be removed if it

is undamaged

3. Remove the connecting ring (4)

and the low pressure valve (15).

CYKLON

1.0:E51

1. Cut off the locking strap (17)

with cutting pliers.

2. Remove the mouth-piece (16)

and the o-ring (12).

1. Remove the lever pin (11).

2. Remove the operating device

(14).

3. Remove the o-ring (12).

4. Unserew the valve seat (5) with

an 8.5 mm screwdriver. NOTE!

the valve seat has a very fragile

tightening edge; put the seat

with the edge upwards.

5. Remove the valve piston (8) and

the spring (9). In order to

protect the piston bond, the old

rubber plate should be kept

until the new shall be fixed.

6. Remove the o-ring (6) with an

oring remover. Make sure the

sealing surfaces ar not

damaged.

IMPORTANT! The ejector sleeve

should not be removed if it is

functional and undamaged.

Check to see that the sleeve can

be rotated to any position, but

that it does not rotate freely.

CYKLON

1.0:E52

When servicing the regulator the

following parts should be replaced:

See chapter Servicekit.

1. All o-rings, including the one in

the low-pressure hose.

2. Rubber plate (7).

CLEANING:

If corrosion or salt deposits occurs, place all metal

parts – concentrated Hempocid* or 15% Hydrochloric

acid for about 10 minutes.Then, rince the parts

thoroughly and blow dry with air. The synthetic parts

in the second stage must not be treated with solvent.

They shall be cleaned in freshwater only.

*Hempocid = Acid Liquid Detergent Containing

phosphoric acid (5 - 10%) and bactericid for

desinfectant cleaning.

BEFORE INSTALLING CHECK THE

FOLLOWING:

1. Diaphragms (21) (23). Check the sealing surface of

the diaphragm to see if it is even and uncracked.

2. The mouth-piece (16).

Make sure that there are no cracks.

3. The purge button (26).

Make sure there are no cracks.

4. Valve piston (8). Ensure that the ball joint is

working correctly by manipulating and rotating

the joint.

5. Operating device (14). Make sure that the joint

articulates smoothly. Important:The operating

device must be replaced, if the lever tab is bent.

The tab should not be straightened, as this would

weaken it and make subsequent failure possible.

6. Valve seat (5). Check to make sure the sealing

surfaces are undamaged.

7. Low pressure hose (3). Check to make sure that the

sealing surface is undamaged, and that the rubber

does not show any flaws.

8. Diaphragm housing (22). Make sure that the

sealing surfaces are free from defeas and that the

track for the inhalation diaphragm is absolutely

clean and free from lubricant.

CYKLON

1.0:E53

Assembly:

Install the ejector sleeve (13) on the

valve housing (10). Press the sleeve into

the low pressure valve so the slits of

the sleeve are exceedingly small.

Lubricate:

Grease:

Oil:

1. Install the o-ring (6) on the valve seat

(5). Make sure that the sealing

surface is not damaged.

2. Lubricate the ball joint. Tilt the

position head according to the

figure to ensure that it rotates and

articulates smoothly.

3. Remove the rubber plate (7) with an

awl and make sure the sealings

surface on the valve is clean. Install

the new rubber plate.

4. Put the spring (9) on the valve

piston (8). Lubricate the spring

5. Install the valve piston/spring in the

valve housing with the flat part of

the valve piston upwards.

Sealing surfaces

CYKLON

1.0:E54

1. Place the valve housing on a

drift seated on a block.

Press the valve housing down,

compressing the spring. Keep

the flat part of the valve piston

parallel with the horizontal slot

in the end of the valve housing.

Move the valve piston up and

down a few times to check for

freedom of movement.

2. Press the valve housing down

and slide an o-ring remover

through the hole in the valve

piston. See diagram.

3. Lubricate the o-ring and the

thread of the valve seat. Screw

in the valve seat with an 8.5 mm

screw driver until the o-ring

remover comes loose.

4. Install the operating device (14).

Insert the lever pin (11) through

the slot, engaging the hole in

the operating device. Rotate the

lever pin 90 degrees to lock it in

place.

CYKLON

1.0:E55

1. Install the o-ring (12).

Lubricate. See diagram.

2. Install the mouth piece (16) and

the plastic band (17). Tighten

and cut off plasticband with

plastic band pliers.

3. Install the o-ring .(12)

4. Lubricate the threads on the

mouth piece

5. Install the low pressure valve

(15) in the mouth piece tube.

Set the indent notch at the top

of the valve housing against the

key at the top of the mouth

piece tube. Screw on the

connecting ring (4).

6. Screw the valve seat down until

the highest part of the

operating device is even with

the level og the opening of the

mouth piece tube. Hold the

second stage valve vertically.

See fig.

CYKLON

1.0:E56

1. Install the purge button (26) in

the cover (24).Screw the button

in the cover-cavity

2. Install the inhalation diaphragm

(23) on the diaphragm housing

(22).

3. Seat the lip on the diaphragm

into the recess on the inner rim

of the diaphragm housing. Use

an o-ring remover or other

blunt pointed instrument.

4. Set the inhalation cover (24) on

the diaphragm housing over the

diaphragm.

5. Place the diaphragm housing

complete with diaphragm and

cover into the frame of the

assembly tool.

6. Insert the locking ring (25) into

the upper groove of the press of

the assembly tool. See diagram

7. Place the press on top on the

diaphragm housing.

8. Tum the knob until you hear or

feel a slight click. Continue

turning until you encounter

resistance, then back off the

knob to release the housing.

9. Check the locking ring

placement to make sure that it

has completely entered the

groove.

CYKLON

1.0:E57

1. Install the exhalation diaphragm

(21) on the diaphragm housing.

Control that the diaphragm is

packing on the diaphragm

housing.

2. Install exhalation diaphragm

cover (20) and locking ring (19).

3. Install the diaphragm housing

on the mouthpiece tube. Be

sure to slip the operating device

into the diaphragm guide

sleeve.

4. Checking the second stage for

leaks: Place the mouth piece

against your lips the low

pressure hose correction with

your thumb and inhale lightly.

This will create a partial vacuum

inside the second stage. If the

pressure does not equalize in 5

seconds the second stage leaks.

See chapter Fault-tracing

scheme.

5. Install the o-ring (2) on the LP

hose and lubricate

6. Screw on the LP-hose. Do not

tighten the connecting ring

until after the function test.

Indice

Altri manuali POSEIDON Strumento subacqueo

POSEIDON

POSEIDON Rebreather Wing Manuale utente

POSEIDON

POSEIDON Rebreather BCD Manuale utente

POSEIDON

POSEIDON 2710 Guida all'installazione

POSEIDON

POSEIDON Xstream Series Manuale utente

POSEIDON

POSEIDON 2801 Guida all'installazione

POSEIDON

POSEIDON M28 Manuale utente

POSEIDON

POSEIDON PEEDB9393 Manuale utente

POSEIDON

POSEIDON Xstream Series Manuale utente

POSEIDON

POSEIDON MKVI Manuale utente

POSEIDON

POSEIDON MKVI Manuale utente

POSEIDON

POSEIDON 0336 - 164 Manuale utente

POSEIDON

POSEIDON Jetstream Guida all'installazione

POSEIDON

POSEIDON PLATFORM Manuale utente

POSEIDON

POSEIDON Pegasus Deluxe Manuale

POSEIDON

POSEIDON 3720 Guida all'installazione

POSEIDON

POSEIDON Cyklon 5000 Manuale utente

POSEIDON

POSEIDON XSTREAM Manuale utente

POSEIDON

POSEIDON M28 Manuale utente

POSEIDON

POSEIDON DRYSUITS Manuale utente

POSEIDON

POSEIDON SE7EN Manuale utente

POSEIDON

POSEIDON SE7EN Manuale utente

POSEIDON

POSEIDON PVH2365 Manuale utente

POSEIDON

POSEIDON 3755 Guida all'installazione

POSEIDON

POSEIDON EBS MkII Manuale utente

Manuali Strumento subacqueo popolari di altre marche

Sherwood

Sherwood Amphos Manuale utente

Zeagle

Zeagle N2ition Manuale utente

Tusa

Tusa Q 1203 CE Guida

Sherwood Scuba

Sherwood Scuba Insight Istruzioni per il montaggio

SUBMERSIBLE SYSTEMS

SUBMERSIBLE SYSTEMS Spare Air 600 Manuale utente

OCEANS

OCEANS S1 Supersonic Manuale utente

heinrichs weikamp

heinrichs weikamp OSTC 2 Manuale utente

Omer

Omer SP2 Manuale utente

Scott

Scott PRO-PAK Manuale utente

Apeks

Apeks BLACK SAPPHIRE Manuale utente

Waterproof

Waterproof DRYSUIT Manuale utente

Dräger

Dräger PAS AirPack 1 Manuale utente

Dive Lab

Dive Lab KIRBY MORGAN KMB 18 Manuale utente

Ratio Computers

Ratio Computers iDive Manuale utente

Oceanic

Oceanic PROPLUS X Manuale utente

CFA

CFA MSA G1 Manuale utente

Genesis

Genesis Centauri Manuale utente

TREND

TREND GAUGE/60 Manuale utente